• 한국진공학회지
• /
• 제15권4호
• /
• pp.410-420
• /
• 2006

Epitaxial 성장에서 screening 및 steering 효과 등과 같은 증착과정 중 나타나는 dynamic effects를 kinetic Monte Carlo 시뮬레이션으로 고찰하였다. 증착원자와 토대 원자와의 상호 작용을 엄밀하게 고려하기 위해 이 시뮬레이션 프로그램에 molecular dynamics 시뮬레이션을 결합시켰다. 기울어진 각도로 증착 시킬 경우 표면의 형상은 1) 증착 각도가 기울어짐에 따라 거칠기가 증가한다는 것, 2) 비대칭적인 언덕의 형성된다는 것, 그리고 3) 언덕의 면방향에 따라 비대칭적인 기울기를 갖는다는 세가지 특징을 보았다. 증착 각도나 온도 의존성에 대한 시뮬레이션 결과는 기존의 실험 결과와 잘 일치하는 것을 확인하였다. 기울어진 각도로 증착했을 때 나타나는 이러한 결과는 steering과 screening 효과에 따른 초기 증착 밀도의 불균일에 기인함을 알 수 있었고, 여기서 steering 효과가 screening 효과 보다 주요한 역할을 하는 것을 보았다. 시뮬레이션 계산에서 확인된 새로운 결과는 기울기 선택 (slope selection)이 이루어졌어도 언덕의 각 면이 단일한 기울기로 형성되어 있지 않고 여러 종류의 facet가 섞인 형태이며, 따라서 기울기 선택이 바로 facet 선택을 의미하지는 않는다는 것이다.

• 한국자동차공학회논문집
• /
• 제10권1호
• /
• pp.209-215
• /
• 2002

A study of the guideway vehicle was made for a comparison of ride stabilities between its two primary steering types; one is the front wheel steering and the other the front-rear wheel. A numerical model as a closed loop system was built for an investigation of various factors to have an influence on the vehicular critical speed which is closely associated with ridabilities. It was shown that dynamics stabilities of the front steering type was much better over a large value of steering gain and the longer distance between front axle and guide link for both types provided better stabilities as well. A large steering gain ratio of the front to the rear significantly plays an important role in an improvement of stability in the front-rear steering. To observe a qualitative trend on stability behaviors, the root locus was obtained by considering a time lag which may be frequently caused by the complicated steering mechanism. In performing so, the appropriate selection of steering gain had a greater effect on the front-rear steering vehicle far more ride comfort. In addition, the dynamics model proposed here can be utilized for a more accurate evaluation on the vehicle design in lateral or yawing absorber and moreover expanded for the analysis of independent four-wheel steering vehicle.

• 한국자동차공학회논문집
• /
• 제4권4호
• /
• pp.38-45
• /
• 1996

Power steering systems play an important role for the vehicle handling characteristics and driver's steering center feeling during straightforward driving situation. In this paper, the rotary valve, the main component of power steering systems, is modeled and analyzed, and is combined with a 3-DOF(degree of freedom) lateral dynamics model of passenger cars to examine the effects of design parameters on the vehicle steering characteristics. The results can be applied to the development of advanced power steering systems for passenger cars such as electronically-con-trolled power steering system.

• Journal of Mechanical Science and Technology
• /
• 제19권spc1호
• /
• pp.444-451
• /
• 2005

The analysis of human arm motion during steering maneuver is carried out for investigation of man-machine interface of driver and steering system Each arm is modeled as interconnection of upper arm, lower arm, and hand by rotational joints that can properly represents permissible joint motion, and both arms are connected to a steering wheel through spring and damper at the contact points. The joint motion law during steering motion is determined through the measurement of each arm movement, and subsequent inverse kinematic analysis. Combining the joint motion law and inverse dynamic analysis, joint stiffness of arm is estimated. Arm dynamic analysis model for steering maneuver is setup, and is validated through the comparison with experimentally measured data, which shows relatively good agreement. To demonstrate the usefulness of the arm model, it is applied to study the effect of steering column angle on the steering motion.

• Journal of Biosystems Engineering
• /
• 제29권5호
• /
• pp.419-424
• /
• 2004

In this study, a series of soil bin experiment was carried out to investigate experimentally the effect of the tire inflation pressure and axle load of tire on the steering torque for the off-road condition. The experiment was performed at the three levels of off-road conditions(ground I, ground II and ground III) and on-road condition(ground IV), four levels of tire inflation pressure(120 kPa, 170 kPa, 220 kPa and 270 kPa), and four levels of axle load(1470N, 1960N, 2450N and 2940N). The results of this study are summarized as follows: 1. Steering torque at the off-road conditions were higher than that on the on-road conditions for all levels of tire inflation pressure and axle load. 2. As the axle load increased, steering torque also increased f3r all experimental ground conditions. 3. For the axle load of 1470N the biggest steering torque was measured on the ground condition I, but as the axle load increased to the value of 2940N the biggest steering torque was measured on the ground condition III. From the above results, it was found that for the low axle load, steering torque gets higher on the soft ground condition, but for the high axle load, steering torque gets higher on hard ground condition for whole range of experimental conditions. 4. As the tire inflation pressure decreased, steering torque increased on the on-road condition, but no specific trend was not found at the off-road conditions.

• 한국자동차공학회논문집
• /
• 제6권2호
• /
• pp.43-53
• /
• 1998

This paper addresses an optimization for reducing a steering error of a rack-and-pinion steering linkage with a MacPherson strut independent front suspension system. The length, orientations and inner joint positions of a tie-rod are selected as design variables and Ackerman geonetry, understeer effect, minimum turn radius, wheel alignment and packaging are considered as design constraints. Nonlinear kinematic analysis of the steering system is performed for calculating the values of cost and constraints, and Augmented Lagrange Multiplier(ALM) method is used for solving the constrained optinization problem. The optimization results show that the steering error are considerably reduced while satisfying all the constraints.

• 한국생산제조학회지
• /
• 제5권3호
• /
• pp.40-49
• /
• 1996

The problem related to the rotational vibration at steering wheel end of passenger cars during high speed driving is investigated. to analyze vibration of steering wheel, a steering system of passenger car is modelled in twelve degrees of freedom including backlash effect of rack and pinion gear system. The one degree of freedom system with backlash in investigated by the analytical method. Consequently the skeleton curve and the frequency response curves are computed. The steering system is analyzed by the numerical simulation using the 4th order Runge-Kutta method, the obtained results are compared with the experimental data. Also the effects of the change of rack gear tooth stiffness and backlash on the acceleration level of steering wheel are investigated. As a result, it can be found that the acceleration level of steering wheel becames lower as the rack gear tooth stiffness becames higher, and that acceleration level becames high as the magnitude of backlash between rack and pinion gear increase.

• 한국자동차공학회논문집
• /
• 제24권1호
• /
• pp.90-98
• /
• 2016

Currently government certified test method for an automobile remanufactured products is insufficient. Thus many automotive parts in the remanufacturing market are lacking proper evaluation criteria and production of defective products are causing customer dissatisfaction. In this paper a power steering oil pump, which requires stringent manufacturing standards, is studied by the failure mode and effect analysis approach. The research suggested that the test criteria such as discharge flow characteristic test, tightness test, pulley run-out test, pressure switch operation test, low temperature test and rotation pressure durability test should be performed to evaluate the reliability of remanufactured power steering oil pumps. As a result of tests, the performance of remanufactured power steering oil pump satisfied the evaluation criteria of pressure switch operation test and low temperature test. However, the remanufactured power steering oil pump failed to satisfy the evaluation criteria on discharge performance test, tightness test and pulley run-out test. These performance evaluation tests proved the necessity of standard process for the remanufactured power steering oil pump.

• International Journal of Automotive Technology
• /
• 제7권3호
• /
• pp.321-327
• /
• 2006

The previous paper described the logic tuning, the vehicle manufacture and the evaluation in the HILS system for the purpose of the development of a Steer-By-Wire(SBW) system. This paper describes the content of applying to a new HILS system, the vehicle manufacture and the result of the evaluation performed in Independent-type SBW(I-SBW) system. Here, the SBW indicates the method of steering both tires by using one motor as the steering gear actuator, similar to the conventional steering system. On the other hand, the I-SBW means the method of steering both front tires independently by using dual motors as the steering gear actuator. As a result, the layout and the kinematical mechanism of the I-SBW system are quite different from those of the typical steering mechanism. Nevertheless, there is no change in the steering column motor system. In the report, we first describe the structure and control logic of the I-SBW system, and then the control effect on this system as applied for both the HILS system and a vehicle. Furthermore, our HILS system involves the actuator mechanism which realizes the reaction force of the road surface with a minimized frictional force in operation. Therefore, it is possible for us to tune the control logic via the HILS system and confirm the effect of the tuned control logic by applying it to a vehicle with the I-SBW system.

• Journal of Biosystems Engineering
• /
• 제30권6호통권113호
• /
• pp.327-332
• /
• 2005

In this study, the electronic power steering control system was developed and it was carried out to investigate experimentally the effect of the steering force for the on-road and off-road. The electronic power steering control system was engineered new trend system of power steering control system for tractor. It was composed of the electronic controller, detector, motor and mechanism mounted on tractor chassis. It was tested at the field in condition of tractor traveling speed 0 km/h, 3 km/h, 8 km/h, 11 km/h, 15 km/h, 18 km/h, 22 km/h, 25 km/h for measuring a maximum steering force. As a speed of tractor increased, a steering force decreased regardless of on-road or off-road. In addition, it is sufficiently a possibility of application of the steering system of tractor.