• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 제7회 압연 심포지엄
• /
• pp.73-76
• /
• 2009

Increase in tensile strength of steel is important for fuel efficiency and $CO_2$ reduction. But the higher the strip strength, the more defect could be generated in hot strip mill. This study focuses on line-type edge scab. One of the causes for the defect is initial edge cracks commonly observed on a slab but their correlation has not been verified yet. Thus, the objective of this report is to verify if the edge crack is exactly the seed for edge scab. For this, we conducted pilot hot rolling test with cracked slab and compared the development of cracks and edge scabs on hot-rolled strip.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권2호
• /
• pp.192-199
• /
• 2002

In continuous galvanizing process, the mass of zinc deposited and its distribution are controlled by the air pressure, effective distance from the air knife nozzle to the steel strip surface and line speed. Coating defects are resulted from the unbalance of these control factors and the inaccuracy of coating equipments. This paper investigates the main cause of coating deviation and a new air knife system for control of coating thickness was developed. We investigate dynamic pressure variation by air knife types. It is found that the coating deviation is caused by the unbalance of dynamic pressure, the irregularity of strip position, and the strip vibration. Formulating a useful coating model by using present working condition, an optimal working condition is suggested. The productivity and coating quality are improved by applying the result of this research at the shop floor.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.211-214
• /
• 2008

The Mechanical properties of steel in hot strip mill were associated with the various rolling conditions such as alloy composition, plastic deformation, cooling history and so on. After coiling process of strip which is the end of hot rolling process, the coil can be the final product or can be applied by another process, that is, cold rolling or skin pass rolling with the additional changes of mechanical properties. Skin pass rolling process with the small reduction affects the mechanical properties of the strip. Because many kinds of hot strips are delivered to the customers after the skin pass process, it is important for us to know the skin pass effects for the mechanical properties of the hot rolling strip. In this study, the variations of mechanical properties of the strip after the skin pass rolling will be discussed. Then, the mathematical model will be proposed for the prediction of mechanical properties of the final products with the comparison between measured and calculated values.

• 소성∙가공
• /
• 제5권3호
• /
• pp.232-238
• /
• 1996

A dynamic mill set-up technique was developed to achieva a more precise roll gap set-up of the finishing mill stands for steel strip rolling. In the conventional mill set-up model the set-up values such as roll gap and roll speed are determined before the sheet bar reached the entry side of the finishing mill train and maintained constant until the strip top end passes through the last stand. In the way however a dynamic set-up logic that gives a way to adjust the roll gap value of the final mill stand for the strip ingoing from the ahead of the front stand was developed and attached to the existing set-up model. The roll gap modification is based on the analysis of the observation in the third stand of the finishing mill train. The dynamic set-up model was proved very effective for the more precise mill set-up and for operational stability in the hot strip finishing mill train.

• 대한기계학회논문집
• /
• 제14권6호
• /
• pp.1689-1699
• /
• 1990

본 연구에서는 Z-Mill의 압연판 형상 예측을 위한 이론 및 컴퓨터 시뮬레이션 에 관한 사항과 설비조건, 압연조건, 소재조건이 판형상에 미치는 영향에 대해 논하고 자 한다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 제5회 압연심포지엄 신 시장 개척을 위한 압연기술
• /
• pp.197-203
• /
• 2004

A full finite element (FE)-based approach is presented for the precision analysis of the strip profile in flat rolling. Basic FE models for the analysis of the mechanical behavior of the strip and of the rolls are described in detail. Also described is an iterative strategy for a rigorous treatment of the mechanical contact occurring at the roll-strip interface and at the roll-roll interface. Then, presented is an integrated FE process model for the coupled analysis of the mechanical behavior of the strip, work roll, and backup roll in four-high mill. A series of process simulation are conducted and the results are compared with the measurements made in hot and cold rolling experiments.

• 한국정밀공학회지
• /
• 제7권1호
• /
• pp.37-52
• /
• 1990

In this study, the characteristics of cooling and rolling during strip casting process is obtained in comparison with the experimental and analytical results. The prupose of this study is to effectively analyze the thermal and mechanical deformation of roller applying the results of the heat transfer and the pressure distribution to boundary conditions. And then the relation between strip thickness and roll deformation is shown. The second purpose is to obtain the proper condition of the continuous casting for stainless steel. The summary and conclusions can be made on the basis of the results obtained by the theories and experiments. a) The strip casting condition for the fine surface quality of tin-alloy as-cast material was obtained in accordance with the velocity of roll rotation and initial roll gap. b) The experimental condition that the dimension of the cast strip thickness coincide with that of the initial roll gap was according to the experimental result of continuous casting by twin-roll type. c) The thermoelastic finite element model to calculate the roll deformation is represented. Thermoelastic model prediction for the roll deformation are in good agreement with the experimental results considering the thermal expansion of the roll. d) The higher cooling rates were obtained by a twin-roller quenching technique. Also quenched microstructure of the rapidly solidified shell was verified. e) The magnitude of roll deformation due to the thermal expansion and roll separating force is quantit- atively represented in the analysis of continuous casting for stainless steel.

• 한국강구조학회 논문집
• /
• 제25권5호
• /
• pp.497-507
• /
• 2013

횡하중을 받는 고층건물에서의 인장역이 형성될 때 강판전단벽의 앵글 변화한다. 본 연구에서는 강판전단벽을 갖는 3층, 9층, 14층 및 20층의 4개 구조물에 대한 유한요소해석 연구를 하였다. 유한요소해석 결과와 각 모델들의 이론식으로 계산된 결과를 비교하여 전단변형 모드와 휨변형 모드로 분류하였다. 전단변형 모드의 모델에서는 주응력 벡터가 일정한 경사각을 이루며 인장역을 발생시킨 반면 휨변형 모델에서는 인장역의 변화는 기존의 이론식과 차이를 보였다.

• 대한기계학회논문집
• /
• 제17권5호
• /
• pp.1193-1201
• /
• 1993

본 연구에서는 통계학적 이론 및 희귀분석에 근거한 보정함수를 모델 수정에 도입하여 조업조건별로 예측오차 요인들을 제거함으로써 예측 모델의 정도를 향상시키 고자 하였다. 이를 위해 일반강에 비해 압연하중 모델의 예측정도가 상대적으로 낮은 극저탄소강을 대상으로 하여 압연조업에 따른 압연하중 예측모델의 오차요인을 조업인 자별로 분석하였고 적용시켜 모델의 적중도를 향상시켰다.

• 제어로봇시스템학회논문지
• /
• 제15권10호
• /
• pp.1062-1070
• /
• 2009

The strip shape for the stainless steel process has made an issue of the strip quality, and hence the shape control method is developed at the Sendzimir rolling mill (ZRM). ZRM is a stainless cold rolling mill and has actuators for the shape control. They are first intermediate rolls and top crown rolls, which are controlled horizontally and vertically, respectively. The shape control of the stainless steel rolling process has difficulty in obtaining the symmetrical shape. The objective of the shape control is to minimize the shape deviation and to maintain stable state, which keeps symmetrical shape pattern in the lateral direction. The method of the shape recognition employs a least squares method and neural network. The shape deviation is the difference between the target shape and actual shape and is controlled by the fuzzy shape control. The fuzzy shape control using operator's informative knowledge is proposed in this paper. The experiments are carried out online for various stainless materials and sizes. The productivity of the rolling process has increased from 9.0 to 9.4 tons per hour.