• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.731-734
• /
• 2009

KIER has been developed a compact and highly efficient fuel processor which is one of the key component of the residential PEM fuel cells system. The fuel processor uses methane steam reforming to convert natural gas to a mixture of water, hydrogen, carbon dioxide, carbon monoxide and unreacted methane. Then carbon monoxide is converted to carbon dioxide in water-gas-shift reactor and preferential oxidation reactor. A start-up time of the fuel processor is about 1h and CO concentration among the final product is maintained less than 5 vol. ppm. To achieve high thermal efficiency of 80% on a LHV basis, an optimal thermal network was designed. Internal heat exchange of the fuel processor is so efficient that the temperature of the reformed gas and the flue gas at the exit of the fuel processor remains less than $100^{\circ}C$. A compact design considering a mixing and distribution of the feed was applied to reduce the reactor volume. The current volume of the fuel processor is 17L with insulation.

• Transactions of the Korean hydrogen and new energy society
• /
• v.22 no.6
• /
• pp.772-779
• /
• 2011

New type of syngas generator based on the partial oxidation of biogas in volumetric permeable matrix reformers was suggested as an effective, adaptable and relatively simple way of syngas and hydrogen production for various low-scale applications. The use of biogas as an energy source reduces the chance of possible emission of two greenhouse gases, $CH_4$ and $CO_2$, into the atmosphere at the same time. Its nature of being a reproducible energy source makes its use even more attractive. Parametric screening studies were achieved as air ratio, biogas component ratio, input gas temperature, Steam/Carbon ratio. As the air ratio was low, the production of the hydrogen and carbon monoxide increased in the condition that 3D matrix reformer maintains the stable driving. As it was the simulation biogas in which the carbon dioxide content is high, the flammable range became narrow. And the flammable range was extended if the injected gas was preheated. The stable driving was possible in the low air ratio. The amount of hydrogen production was increased as S/C ratio increased.

• Journal of the Korean institute of surface engineering
• /
• v.35 no.5
• /
• pp.312-318
• /
• 2002

A study on the change of mechanical properties and oxidation behavior of Zircaloy-4 fuel cladding after exposing at 90$0^{\circ}C$ and $1000^{\circ}C$ for various periods of exposure time under the steam atmosphere was carried out. The growth of the $ZrO_2$ layer combined with an oxygen-rich-phase layer into the Zircaloy tube material can be described by an expression, E = 1.1√Dt + $2 $\times$ 10^{-4}$ . The tensile strength of Zircaloy tubes increased for a short period of exposure time and decreased rapidly with further exposure while the hoop strength was not decreased greatly. In the meantime, the axial and circumferential elongations of oxidized Zircaloy tubes were decreased drastically with increasing exposure time as a result of embrittlement phenomena.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.8
• /
• pp.1178-1184
• /
• 2008

In this study, techniques of ion implantation were used in order to improve the characteristics of metal materials such as the oxidation and wear resistant. In particular it is necessary to develope their oxidation and wear resistant that could be used in severe environmental conditions. There are mainly two elementary technologies including ion implantation and/or thin film coating. Ion implantation method was performed for surface modification. As a result, it was found that some ion implantations methods such as Nb, high-temperature Nb ion implantation and Nb+C combined implantation are somewhat effective for improving the oxidation resistance of TiAl alloy. Furthermore, the fluorine PBII treatment is more effective for improving the oxidation resistance of the TiAl alloy with three-dimensional shapes. The implantation of boron ion into thin film of TiN was also effective for improving the properties of materials like high temperature wear resistance. TiCrN film was applied to the actual seal ring for steam turbines, and it was observed that its sliding property showed a successfully good performance.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.735-738
• /
• 2000

This paper shows experimentally that oxide layer on the p-type Si-substrate can grow at low temperature(500$^{\circ}C$∼600$^{\circ}C$) using high pressure water vapor system. As the result of experiment, oxide layer growth rate is about 0.19${\AA}$/min at 500$^{\circ}C$, 0.43${\AA}$/min at 550$^{\circ}C$, 1.2${\AA}$/min at 600$^{\circ}C$ respectively. So, we know oxide layer growth follows reaction-controlled mechanism in given temperature range. Consequently, granting that oxide layer growth rate increases linearly to temperature over 600$^{\circ}C$, we can expect oxide growth rate is 5.2${\AA}$/min at 1000$^{\circ}C$. High pressure oxidation of silicon is particularly attractive for the thick oxidation of power MOSFET, because thermal oxide layers can grow at relatively low temperature in run times comparable to typical high-temperature, 1 atm conditions. For higher-temperature, high-pressure oxidation, the oxidation time is reduced significantly

• Applied Chemistry for Engineering
• /
• v.9 no.7
• /
• pp.956-960
• /
• 1998

Cu-Zn and Cu-Zn-Ti catalysts for the steam reforming of methanol were prepared. This reaction was carried out at atmospheric pressure, $250^{\circ}C$, steam/methanol molar ratio 1.5, and contact time 0.1 g-cat.hr/mL-feed. In case of the catalyst with 3 mol% of $TiO_2$, the activity was superior to that of catalysts without $TiO_2$. The reaction products were mainly hydrogen and carbon dioxide. It was found that catalytic activity was not related to specific surface area but affected by metallic copper area which was measured by $N_2O$ decomposition and increased with the addition of $TiO_2$ content. XPS and XRD showed that the oxidation state of zinc was not changed during reaction, but oxidation states of copper existed in Cu(0) or Cu(I).

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.1
• /
• pp.9-16
• /
• 2015

This study was carried out to investigate the effect of delignification on properties of lignocellulose nanofibers (LCNFs) prepared by wet disk-milling (WDM) after steam and ozone oxidation pre-treatments and their nanopaper sheets. Delignification treatment was effective to obtain fine morphology with uniform fiber diameter less than 35 nm without aggregation, and increased the specific surface area (SSA) and filtration time of LCNFs. In particular, SSA and filtration time of the LCNFs prepared by WDM after ozone pretreatment increased 1.5 and 5.4 times after further delignification. Delignification also increased whiteness and decreased the redness of nanopaper sheets. The highest color difference (41.9) before and after the delignification was obtained in LCNFs prepared by WDM after the steam pretreatment. Tensile properties of nanopaper sheets were also increased by further delignification. The highest tensile strength was found to be 142 MPa.

• Korean Journal of Food Science and Technology
• /
• v.41 no.5
• /
• pp.587-591
• /
• 2009

Volatiles in Artemisia princeps Pampan. cv. sajabal (sajabalssuk) and A. princeps Pampan. (ssuk) treated with different processing were analyzed using headspace-solid phase microextraction (HS-SPME)/gas chromatography- a mass selective detector (GC-MS). Sajabalssuk and ssuk were treated with steam distillation (SD) and freeze-dried/steam distillation (FD/SD) while controls were raw sajabalssuk and raw ssuk. Sajabalssuk had significantly more total volatiles than ssuk in control and FD/SD treated samples (p<0.05). Major volatiles in raw sajabalssuk were 2-hexenal, 1,8-cineol, trans-caryophyllene, and hexanal while those in raw ssuk were 1-hexanol, ${\beta}$-myrcene, limonene, and 2-hexenal, which implies that substantial lipid oxidation occurred in raw samples. Sajabalssuk with SD and FD/SD treatment had higher peak areas of 1,8-cineole, 4-terpineol, 1-octen-3-ol, and ${\alpha}$-terpineol while ssuk with SD and FD/SD treatment possessed 1,8-cineol, camphor, borneol, artemisia ketone, ${\alpha}$-thujone, and 1-octen-3-ol, which showed that steam distillation produced more volatiles from terpenoids than raw samples. Based on the results of HS-SPME/GC-MS, relative amounts of volatiles from lipid oxidation including 2-hexenal, hexanal, and 1-hexanol were reduced in sajabalssuk and ssuk with freeze-drying and/or steam distillation treatment.

• Korean Journal of Materials Research
• /
• v.29 no.1
• /
• pp.7-10
• /
• 2019

Cr-Al alloys are attracting attention as oxidation resistant coating materials for high temperature metallic materials due to their excellent high temperature stability. However, the mechanical properties and oxidation resistance of Cr-Al alloys can be further enhanced, and such attempts are made in this study. To improve the properties of Cr-Al alloys, Si is added up to 5 wt%. Casting specimens with different amounts of Si content are prepared by a vacuum arc remelting method and isothermally heated under steam conditions at $1,100^{\circ}C$ for 1 hour. The as-cast microstructure of low Si alloys is mainly composed of only a Cr phase, while $Al_8Cr_5$ and $Cr_3Si$ phases are also observed in the 5 % Si alloy. In the high Si alloy, only Cr and $Cr_3Si$ phases remain after the isothermal heating at $1,100^{\circ}C$. It is found that Si additions slightly decrease the oxidation resistance of the Cr-Al alloy. However, the microhardness of the Cr-Al alloy is observed to increase with an increasing Si content.

• Korean Journal of Food Science and Technology
• /
• v.43 no.6
• /
• pp.711-718
• /
• 2011

Effects of heating conditions and seed roasting on the lipid oxidation and antioxidants of perilla seeds were studied. Perilla seeds, that were unroasted or roasted at $180^{\circ}C$ for 20 min, were ground and heated over steam at $100^{\circ}C/1$ atm or at $135^{\circ}C/2$ atm. Lipid oxidation was evaluated by peroxide value, conjugated dienoic acids contents, and fatty acid composition. Tocopherols and polyphenols were also determined. Lipid oxidation of perilla seeds was higher during heating at $135^{\circ}C/2$ atm than at $100^{\circ}C/1$ atm, and the oxidation rate was lower in unroasted seeds than in roasted seeds. Degradation of tocopherols and polyphenols in perilla seeds during heating was faster under high pressure and temperature, and was decreased by seed roasting. Contribution of polyphenols to the oxidative stability of perilla seeds during heating was higher than that of tocopherols, suggesting polyphenols and seed roasting as important factors in lipid oxidation of perilla seeds.