• International Journal of Aeronautical and Space Sciences
• /
• v.16 no.3
• /
• pp.425-436
• /
• 2015

This paper presents the procedures used for estimating the stability and control derivatives of a general aviation canard aircraft from flight data. The maximum likelihood estimation method which accounts for both process and measurement noise was used for the flight data analysis of a four seat canard aircraft, the Firefly. Without relying on the parameter estimation method, several aerodynamic derivatives were obtained by analyzing the steady state flight data. A wind tunnel test, a flight test of a 1/4 scaled remotely controlled model aircraft, and the prediction of aerodynamic coefficients using the USAF Stability and Control Digital Data Compendium (DATCOM), Advanced Aircraft Analysis (AAA), and Computer Fluid Dynamics (CFD) were performed during the development phase of the Firefly and the results were compared with flight determined derivatives of a full scaled flight prototype. A correlation between the results from each method could be used for the design of the canard aircraft as well as for building the aerodynamic database.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.55 no.4
• /
• pp.402-410
• /
• 2019

This paper deals with the disturbance observer (DOB) based sliding mode control (SMC) for a DC motor to control motor rotating speed precisely and to ensure strong robustness against disturbance including load torque and parameter variation. The reason of steady state error in speed on conventional SMC without DOB is analyzed in detail. Especially, the suggested DOB is designed to prevent measuring noise and harmonics caused by derivative operation on rotating speed. The control performance of the DOB based SMC is evaluated by the various simulations. The simulation results showed that the DOB based SMC had more robust performance than the SMC system without DOB. Especially, precise speed control was possible even though motor parameter variation and load torque was added to the system.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.840-845
• /
• 2004

In many applications, piezoelectric motor has been used in the areas where excellent controllability, fine position resolution are required or magnetic field noise should be eliminated. However the piezoelectric motor has two major demerits. One is difficulty in maintaining vibration amplitude constantly with temperature rise and wear, and the other is heat generation induced by dielectric and mechanical loss. In this thesis, piezoelectric motor to overcome these problems is proposed. And proposed piezoelectric motor is operated using momentum exchange between bimorph and rotor. To maximize steady state velocity and static torque of proposed motor, the guideline is established using two bimorph models. Then the guideline is partially proved by comparison between simulation and experiment. There was no heat generation in the few hours of experiments.

• Journal of Power Electronics
• /
• v.14 no.4
• /
• pp.796-805
• /
• 2014

A digital controller with a low-power approach for point-of-load synchronous buck converters is discussed and compared with its analog counterpart to confirm its feasibility for system integration. The tri-mode digital controller IC in $0.35{\mu}m$ CMOS process is presented to demonstrate solutions that include a PID, quarter PID, and robust RST compensators. These compensators address the steady-state, stand-by, and transient modes according to the system operating point. An idle-tone free condition for ${\Sigma}-{\Delta}$ DPWM reduces the inherent tone noise under DC-excitation. Compared with that of the traditional approach, this condition generates a quasi-pure modulation signal. Experimental results verify the closed-loop performances and confirm the power-saving mechanism of the proposed controller.

• Journal of KSNVE
• /
• v.10 no.1
• /
• pp.97-106
• /
• 2000

The dynamic behavior of crankshaft-bearing system in scroll compressor has been investigated using the combined methodologies of finite elements and transfer matrices. The finite element formulation is proposed including the field element for a shaft section and the point element at balancer weight locations, bearing locations, etc., whereas the conventional method is used with the elements. The Houbolt method is used to consider the time march for the integration of the system equations. The linear stiffness and damping coefficients are calculated for a finite cylindrical fluid-film bearing by solving the Reynolds equation, using finite difference method. The orbital response of crankshaft supported on the linear bearing model is obtained, considering balancer weights of motor rotor. And, the steady state displacement of crankshaft are compared with a variation in balancer weight. The loci of crankshaft at bearing locations are composed of the synchronous whirl component and the non-synchronous whirl component.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.11
• /
• pp.138-145
• /
• 2009

A suspended membrane micro fluidic heat flux sensor that is able to measure the heat flow rate was designed and fabricated by a complementary-metal-oxide-semiconductor-compatible process. The combination of a thirty-junction gold and nickel thermoelectric sensor with an ultralow noise preamplifier, low pass filter, and lock-in amp has enabled the resolution of 50 nW power and provides the sensitivity of $11.4\;mV/{\mu}W$. The heater modulation method was used to eliminate low frequency noises from sensor output. It is measured with various heat flux fluid of DI-water to test as micro fluidic application. In order to estimate the heat generation of samples from the output measurement of a micro fluidic heat-flux sensor, a methodology for modeling and simulating electro-thermal behavior in the micro fluidic heat-flux sensor with integrated electronic circuit is presented and validated. The electro-thermal model was constructed by using system dynamics, particularly the bond graph. The electro-thermal system model in which the thermal and the electrical domain are coupled expresses the heat generation of samples converts thermal input to electrical output. The proposed electro-thermal system model shows good agreement with measured output voltage response in transient state and steady-state.

• Journal of Institute of Control, Robotics and Systems
• /
• v.4 no.1
• /
• pp.45-55
• /
• 1998

In this paper, a robust path tracker and depth controller of Autonomous Underwater Vehicle based on sliding mode control is presented. We have also designed augmented equivalent control inputs by analyzing the sliding mode with the reaching mode. This can enhance the reaching rate, and improve chattering problems, that is, noise caused by the control plane actuator of the vehicle, which is one of the problems that occur when sliding mode control is used. Also to resolve the steady state error generated in the path tracker under current effect, a modified sliding plane is constructed. Also a redesigned sliding plane and control input using transformation matrix is proposed to do easy design of MIMO depth controller. For state variables that cannot be measured directly, reduced order sliding mode control is used to design an observer. The performance of designed path tracker and depth controller is investigated by computer simulation. The results show that the proposed control system has robust performance to parameter variation, modelling error and disturbance.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.11a
• /
• pp.230-236
• /
• 2001

We developed a built-in sensor bearing to measure the rotor motion of a rolling piston type compressor for the air conditioner. Because of needs for the high efficiency and long life span of compressor, and the usage of alternative refrigerants, the operating condition of the compressor becomes more severe. The accurate measurement of the rotor motion of the compressor can contribute greatly to the design and analysis of the hydrodynamic bearing. However, it is difficult to measure accurately the shaft behavior of small compressor because of the small space for the sensor mount, high temperature and pressure of compressor, oil mixed with refrigerant, and electromagnetic noise of the motor. To overcome these difficulties, we develop the cylindrical capacitive sensor that is built in the hydrodynamic bearing and calibrate the built-in sensor bearing indirectly through measuring the oil relative permittivity. We measured the rotor motion as well as suction and discharge pressures in various conditions. The several experimental results show that the developed built-in sensor bearing can measure the rotor motion not only in steady state but also in transient state.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.2
• /
• pp.361-366
• /
• 2017

The abnormal state of the main equipment across the industry is accompanied by abnormal rise of temperature, change in the vibration and noise. In this study, we developed a smart sensing module equipped with BLE, and developed a smart sensing device that can detect abnormal vibration due to its own flaws of the equipment by interfacing with an MEMS-based acceleration sensor. The smart sensing device developed in this study can be easily installed in a small space and can monitor the vibration status of the equipment in real time, and can easily inform the user of the steady state and the problem occurrence status with array LED display.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.2
• /
• pp.247-252
• /
• 2015

Adaptive algorithms based on the criterion of zero-error probability (ZEP) have robustness to impulsive noise and their decision feedback (DF) versions are known to compensate effectively for severe multipath channel distortions. However the ZEP-DF algorithm computes several summation operations at each iteration time for each filter section and this plays an obstacle role in practical implementation. In this paper, the ZEP-DF with recursive gradient estimation (RGE) method is proposed and shown to reduce the computational burden of O(N) to a constant which is independent of the sample size N. Also the weight update of the initial state and the steady state is a continuous process without bringing about any propagation of gradient estimation error in DF structure.