• Proceedings of the KIEE Conference
• /
• 2000.11b
• /
• pp.384-386
• /
• 2000

This paper describes a new approach to estimating permanent magnet synchronous motor(PMSM) speed and position from measured terminal voltages and currents for speed-sensorless vector control. The proposed system is based on observing the instantaneous reactive power of the motor. The described technique is very simple and robust to variations of motor parameters. The new approach is not dependent upon the value of the stator resistance. Also, MRAS schemes are chosen for determining the adaptive law for the speed and the position estimator. The effectiveness is verified by the experimental results.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.422-425
• /
• 2001

권선형 유도전동기는 기동시에 충분히 큰 저항을 외부에서 삽입하여 기동전류를 작게하는 동시에 기동 토크를 크게 할 수 있다. 또한, 유도전동기의 각 기동 방식중에서 가장 우수한 시동특성을 가지고 있으며 크레인, 시멘트공장 등 중부하 시동이 요구되는 경우 널리 사용되고 있다. 권선형 유도전동기 드라이브 시스템의 전류, 토크, 위치 및 속도 등의 제어를 위하여 일반적으로 산업현장에서는 Pl 제어기가 많이 적용되고 있다. 그러나 이러한 시스템은 센서 부착시 여러가지 환경적 제약으로 인한 전체시스템의 성능 저하를 가져올 수 있어 이를 개선하기 위한 센서리스 벡터제어가 활발히 연구되고 있다. 본 논문은 권선형 유도 전동기의 센서리스 벡터제어를 위해 MRAS 기법을 적용하였고, 기존의 MRAS 기법 적용시 발생하는 파라미터 변동에 따른 속도추정오차를 개선하기 위해 센서리스 벡터제어의 속도제어에 크게 영향을 미치는 고정자 저항을 온라인으로 튜닝함으로서 파라미터 변화에 강인한 센서리스 속도제어를 구현하였다. 제안된 기법의 타당성 및 유효성을 디지털 컴퓨터에 의한 시뮬레이션에 의해 확인하였다.

• Journal of Power Electronics
• /
• v.10 no.4
• /
• pp.396-404
• /
• 2010

This paper presents simple schemes used to estimate the initial rotor position and the d- and q-axis inductances for effective Maximum Torque per Ampere (MTPA) operation in a wind-power system using an IPMSM (Interior Permanent Magnet Synchronous Machine). An IPMSM essentially requires an exact coordinate transformation and accurate inductance values to use a reluctance torque caused by the saliency characteristic. In the proposed high-frequency voltage testing method, there is no voltage drop caused by the resistance and the electromotive force. The initial rotor position and the inductance can be measured through an analysis of the stator current without turning the rotor. The experimental results are presented in order to illustrate the feasibility of the proposed method.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1047-1048
• /
• 2007

In this paper, the harmonic loss of the inverter driven induction motor was analyzed. It was analyzed through the theoretical consideration on the variations of equivalent circuit constants, and harmonic losses, including the effects of resistance increase and inductance decrease of stator, not through the general method that considering just the effects of the harmonic losses of only the rotor. It was verified by comparing the harmonic analysis results with the test results for HHI's inverter driven motor.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.52 no.4
• /
• pp.154-154
• /
• 2003

The switched reluctance motor(SRM) has a considerable potential for industrial applications because of its high reliability as a result of the absence of rotor windings. In some applications with SRM, a parallel switching strategy is often used for cost saving, increasing of current capacity and system reliability. This paper proposes a new parallel switching strategy of SRM using parallel winding. While conventional parallel switching devices are connected in a phase winding, power devices are connected in the parallel windings wound in each pole of stator in the proposed method. Paralleling strategy for current sharing in the proposed method can be easily determined without considerations of any nonlinear characteristics of power devices such as conduction resistance, threshold voltage and gain factor. The proposed paralleling strategy is verified by the mathematical analysis and experimental results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.763-766
• /
• 2000

In this paper, stator form-winding sample coils based on silicone resin and polyimide were made for fault prediction and reliability estimation on the 200 Class insulation system of traction motors. The complex accelerative degradation was performed by periods during 10 cycles, which was composed of thermal stress, fast rising surge voltage, vibration, water immersion and overvoltage applying. After aging of 10 cycles, condition diagnosis test such as insulation resistance & polarization index, capacitance & dielectric loss and partial discharge properties were investigated in the temperature range of 20∼160$^{\circ}C$. Relationship among condition diagnosis test was analyzed to find an dominative degradation factor and an insulation state at end-life point.

• Proceedings of the KIEE Conference
• /
• 1995.07a
• /
• pp.353-356
• /
• 1995

This paper proposes a simple identification method of the rotor time constant to solve the degradation of motor performance due to the difference between the rotor time constant of a controller and actual one in slip frequency type vector control scheme. The proposed method is based on rotor induced voltage equations and it is confirmed that immunity of the stator resistance thermal variation. The simulation results show that the proposed method suitably identifies the rotor time constant in steady state as well as in transient state.

• Journal of Electrical Engineering and information Science
• /
• v.1 no.2
• /
• pp.58-66
• /
• 1996

An adaptive input-output linearization technique of an interior permanent magnet synchronous motor with a specified output dynamic performance is proposed. The adaptive parameter estimation is achieved by a model reference adaptive technique where the stator resistance and the magnitude of flux linkage can be estimated with the current dynamic model and state observer. Using these estimated parameters, the linearizing control inputs are calculated. With these control inputs, the input-output linearization is performed and the load torque is estimated. The adaptation laws are derived by the Popov's hyperstability theory and the positivity concept. The robustness and the output dynamic performance of the proposed control scheme are verified through the computer simulations.

• Journal of IKEEE
• /
• v.24 no.4
• /
• pp.954-960
• /
• 2020

This paper proposes a speed variable proportional resonant current control method for a single-phase permanent magnet synchronous motor(PMSM). Due to the electromagnetic characteristics of a single-phase PMSM, negative and zero torques are generated in the part corresponding to the phase difference between the stator current and the back electromotive force. In addition, overcurrent limitation is required because of the low stator resistance and inductance in sensorless operation. When using the vector control for current control of single-phase PMSM under these conditions, processes of coordinate transformation, inverse coordinate transformation, and generation of virtual dq-axis components are required. However, the proposed variable speed proportional resonant current control method does not need the coordinate transformation used for AC motors. In this paper, we have confirmed stable maneuverability by using variable proportional resonant current control algorithm, and proposed sensorless control based on a mathematical model of a single-phase PMSM without a position sensor when reaching a constant speed. The usefulness of the current control method was verified through several experiments.

• KEPCO Journal on Electric Power and Energy
• /
• v.6 no.4
• /
• pp.467-472
• /
• 2020

The superconducting synchronous generator is one of the breakthrough elements for direct-drive wind turbines because it is light and small. Normally the superconducting one has copper armature windings in the stator and superconducting field windings on the rotor. The high resistance of the armature can make large copper losses, comparing with the conventional generators with a gear box. One of the solutions for the large copper losses could be a fully superconducting generator. But the high magnetic fields from the superconducting field windings on the rotor also make high perpendicular magnetic fields on the superconducting tapes in the armature windings. We have proposed a fully superconducting synchronous generator with dual field windings. It could immensely decrease the circumferential component of the magnetic field from the field windings at the armature windings. In this paper, we conceptually designed 3 types of superconducting synchronous generators. The first one is the fully superconducting one with conventional structure, which has superconducting armature windings in the stator and superconducting field windings on the rotor. The second one is the one with dual superconducting field windings and superconducting armature windings between them. The last one is the same as the third one except the structure of the armature. If the concentrated armature windings are superconducting ones with cryostats, then they cannot be installed within the span of 2 poles. So, we adopted 3 phases windings within 4 poles system. It makes more AC losses but can be manufactured really.