• Proceedings of the KIEE Conference
• /
• 1995.07a
• /
• pp.206-208
• /
• 1995

Recently according to the increasing critical loads such as communication and life support systems stable power supplying becomes more and more important. Therefore it is indespensable to stabilize power source using these instruments - AVR(Automatic Voltage Regulator) or UPS(Uninterrutible Power Supply). This paper deals with ON-LNE UPS which is composed of PWM converter for AC-DC conversion. Using a PWM converter have advantages of low current harmonics and high power factor. In this paper ON-LNE UPS using PWM converter is proposed and its characteristics are investigated.

• Bulletin of the Korean Chemical Society
• /
• v.10 no.3
• /
• pp.258-261
• /
• 1989

The electrochemical behaviors of 4-(2)-thiazolylazo)-resorcinol (TAR) in acetonitrile solution was studied by DC polarography, cyclic voltammetry, controlled-potential coulometry and UV-Vis spectroscopy. The electrochemical reduction of TAR occurs in four-one electron reduction steps in acetonitrile solution. The products of the first and the third electron transfer are speculated to be a relatively stable anion radical. The second electron transfer to the dianion is followed by a chemical reaction producing a protonated species. The product of the fourth electron transfer also produces the corresponding amine compounds with a following reaction. Also every reduction wave was diffusion controlled. The first reduction wave is considerably reversible and the other waves are less reversible.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.1
• /
• pp.80-83
• /
• 2022

This paper proposes an initial rotor polarity detection algorithm of a single-phase permanent magnet synchronous motor (SP-PMSM) related to stable open-loop starting for sensorless operation. Generally, the SP-PMSM needs an asymmetric air-gap structure to can avoid the initial starting failure at zero torque point. Therefore, the rotor polarity information can be obtained by using the DC offset current direction of a stator current through a high frequency voltage injection into an SP-PMSM with an asymmetric air gap. In this paper, the proposed rotor initial polarity detection algorithm is verified through several experimental results.

• Korean Journal of Veterinary Research
• /
• v.36 no.3
• /
• pp.541-550
• /
• 1996

Tetracycline antibiotics have been widely used not only therapeutics but feed additives. There are many methods for the isolation and determination of tetracycline antibiotics in animal muscle tissue. But those methods take much time and labor, so it is difficult to analyse many samples simultaneously. A rapid isolation method and liquid chromatographic determination of tetracycline antibiotics in animal muscle tissue (bovine, porcine, chicken) is presented. Blank control and tetracyclines fortified samples (0.5g) were blended with $C_{18}$ containing 0.05g each of oxalic acid and disodium ethylenediaminetetraacetate. After homogenize, homogenate was transferred to glass column made from 10ml glass syringe and compressed to 4~4.5ml volume. A column made from the $C_{18}$/meat matrix was washed with hexane (8ml) and dichloromethane (8ml, if needed), following which the tetracyclines were eluted,vith methanol or 0.01M methanolic oxalic acid (8ml). The eluates containing tetracyclines analytes were free from interfering compounds when analysed by HPLC with UV detection (photodiode array at 360nm). Standard curve for each tetracycline showed a linear response at the range of $0.05{\sim}1.0{\mu}g/ml$ and tetracycline antibiotics were eluted within 4ml of eluted volume. All tetracycline antibiotics except tetracycline were stable during the concentration process at $40^{\circ}C$ and time required for concentration was 3~4 hours. Fortified samples containing oxalic aicd and EDTA represented more good recoveries than those of not-contained sample. Recoveries were 91.8~110.1% (oxytetracycline; OTC), 57.7~79.5% (tetracycline; TC), 78.1~88.6% (chlortetracyclines; CTC) and 88.4~100.6% (doxycycline; DC) in pork tissue, 101.1~126.8% (OTC), 66.4~75.4% (TC), 79.2~88.1% (CTC) and 69.3~86.7% (DC) in beef tissue, and 90.8~95.6% (OTC), 66.2~84.4% (TC), 75.7~77.2% (CTC) and 55.6~80.7% (DC) in chicken muscle tissue. The detection limits validated in muscle tissue by this method were $0.05{\mu}g/g$ for OTC and TC, and $0.1{\mu}g/g$ for CTC and DC.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.3C
• /
• pp.141-148
• /
• 2010

Electrical noises like self potential, burst noises and 60-Hz electrical noises are one of the causes to reduce reliability of electrical resistivity survey. Even the PDC-R (Pseudo DC resisitivity) technique, recently developed, is suffering from the problem of low reliability due to electrical noises. That is, both DC-based and AC-based resistivity technique is subject to reliability problem due to electrical noises embedded in urban geotechnical sites. In this research, a new technique to enhance reliability of the PDC-R technique by minimizing influence of electrical noises was proposed. In addition, an automated procedure was also proposed to facilitate data analysis and interpretation of PDC-R measurements. The proposed technique is composed of two steps: 1. to extract information only related with the input current by means of multiple-filter technique, and 2. to undertake a task to sort out signal information only to show stable and reliable characteristics. This automated procedure was verified by a synthetic harmonic wave including DC shift, burst random noises and 60-Hz electrical noises. Also the procedure was applied to site investigation at urban areas for proving its feasibility and accuracy.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.17 no.2
• /
• pp.187-198
• /
• 1997

This experiment was conducted to evaluate effects of wilting and additives on fermetation characteristics, quality and aerobic stability of silage of rye(Seca1e cereale L.) harvested at the early heading stage. Harvested rye was wilted or mixed with beet pulp and then treated with formic acid or lactic acid bacteria(LAB) inoculant. Treatments were consisted of direct cut(DC), wilted(WT), beet pulp added(BP), direct cut and formate applied(DF), wilted and formate applied(WF), beet pulp and formate applied(BF), direct cut and LAB inoculated(DL), beet pulp added and LAB inoculated(BL), and wilted and LAB inoculated(WL) silages. Afler 70 days of ensiling period, the silages were opened and exposed to air for 7 days, and the silages of opening day(0 day) were compared with the silages exposed to air for 7 days(7 day). 1. LAB inoculated rye silages(DL, WL, BL) lowered pH values effectively eom the third day of ensiling and showed most stable pattern of pH changes during the initial fermentation process. Direct cut and formate applied(DF), beet pulp and formate applied(BF) and beet pulp added(BP) silages were also effective in lowering pH from the seventh day thai direct cut treatment(DC). 2. pH was low below 3.7 in all treatments of 0 day. After 7-day period of aerobic exposure, DL and WL showed considerable increases in pH from 3.5 and 3.4 to 8.3 and 6.4, respectively. 3. Direct cut rye silages(DF, DC, DL) and beet pulp and formate treatment(BF) produced effluent of 121.2, 85.9, 80.3 and 34.2 mlkg, respectively and these were greater than others(P<0.01). Beet pulp retained 1.61 I/kg of effluent at the application rate of 50 kg/t in comparing BP with DC, and formate application increased the amount of effluent in comparing DF and BF with DC and BP, respectively(P<0.01). 4. Beet pulp and LAB treatment(B1) was highest in content of lactate as 3.1% and formate treated silages(DF, WF, BF) showed lower content of lactate and total acid than others. LAB inoculated(D1, WL, BL) and wilted (WT) silages were graded to be good quality as a second group by the Flieg's score. Formate applied silages (DF, WF, BF) were graded as a foum group lower than DC by one. 5. Residual content of WSC of rye silage was higher in BP, BF, DL and BL than direct cut treatment(M3) (P< 0.01). Formate application had a tendency to increase the content of residual content of WSC. 6. For the ratio of NH3-N to Total N, wilted and LAB inoculated(W1) and direct cut and LAB inoculated(D1) silages were lowest on 0 day as 8.9 and 9.3% respectively. But after 7-day period of aerobic exposure, WL and DL showed largest increase of the ratio of $NH_3-N$ to Total N from 0 day(P<0.01). 7. On 0 day wilted(WT), beet pulp and formate treatment(BF), and beet pulp and LAB treatment(B1) were lower than direct cut treatment(DC) for NDF and ADF concentrations consistently. Formate applied silages (DF, WF, BF) made little change in ADF and NDF concentrations during 7 day period of aerobic exposure. DL and WL showed a large increase in ADF and NDF concentrations under aerobic condition(P<0.01). 8. IVDMD values of wilted(WT), beet pulp added(BP), wilted and LAB inoculated(W1) and beet pulp added and LAB inoculated(B1) silages were higher than direct-cut treatmentPC) as 84.7, 84.7, 84.4 and 83.0%, respectively on 0 day. But during 7-day period of aerobic exposure, a great decreae in IVDMD of WL was showed(P<0.01). The experimental results indicate that wilted silage(WT) could be recommended as the most effective treatment for reducing efluent and increasing quality and feed value of rye silage without deteriorating aerobic stability more than direct cut treatment(DC). Additionally, under unfavorable weather condition beet pulp added and LAB inoculated treatment(T3L) might be the possible alternative for successful ensiling of forage rye.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.5
• /
• pp.495-501
• /
• 2005

Al is a active metal that owes its resistance to a thin, protective, barrier oxide surface layer, which is stable in air and neutral aqueous solution. Thus Al alloys are widely used in architectural trim. cold & hot-water storage vessels and piping. However Al and most of its alloy may corrode with some forms such as pitting corrosion, intergranular corrosion and galvanic corrosion in the case of exposure to various industrial and marine atmosphere. Therefore a correct evaluation of corrosion resistance for their Al and Al alloys may be more important in a economical point of view. In this study. a relative evaluation of corrosion resistance for three kinds of Al alloys such as ALDC2, ALDC3, and ALDC8 series was carried out with electrochemical method. There is a tendency that corrosion potential is shifted to positive or negative direction by alloying components regardless of corrosion resistance. Moreover the data of corrosion properties obtained from cathodic Polarization curve, cyclic voltammogram and AC. DC impedance respectively showed a good correspondence each other against the corrosion resistance but variation of corrosion potential. passivity current density of anodic polarization curve and corrosion current density by Tafel extrapolation and Stern-Geary method didn't correspond with not only each other but also considerably the data of corrosion properties discussed above. Therefore it is suggested that an optimum electrochemical evaluation for corrosion resistance of Al alloy is to calculate the diffusion limiting current density of cathodic polarization curve, impedance of AC or DC and polarization resistance of cyclic voltammogram.

• Transactions of the Korean hydrogen and new energy society
• /
• v.25 no.3
• /
• pp.271-279
• /
• 2014

A 25kW-class polymer electrolyte membrane (PEM) fuel cell system has been developed for the propulsion of a leisure boat. The fuel cell system was designed to satisfy various performance requirements, such as resistance to shock, stability under rolling and pitching oscillations, and durability under salinity condition, for its marine applications. Then, the major components including a 30kW-class PEM fuel cell stack, a DC-DC converter, a seawater cooling system, secondary battery packs, and balance of plants were developed for the fuel cell system. The PEM fuel cell stack employs a unique design structure called an anodic cascade-type stack design in which the anodic cells are divided into several blocks to maximize the fuel utilization without hydrogen recirculation devices. The performance evaluation results showed that the stack generated a maximum power of 31.0kW while maintaining a higher fuel utilization of 99.5% and an electrical efficiency of 56.1%. Combining the 30-kW stack with other components, the 25kW-class fuel cell system boat was fabricated for a leisure. As a result of testing, the fuel cell system reached an electrical efficiency of 48.0% at the maximum power of 25.6kW with stable operability. In the near future, two PEM fuel cell systems will be installed in a 20-m long leisure boat to supply electrical power up to 50kW for propelling the boat and for powering the auxiliary equipments.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.7
• /
• pp.809-815
• /
• 2016

In this paper, the electrical values of resistance, current, and voltage condition of reactivity is analyzed by applying the direct current (DC) voltage in medium for stem cell regeneration treatment. The voltage response by medium is related to electrical stimulation in the process of induction of differentiation for stem cell and the differentiation condition can be checked depending on the response of voltage condition. If the voltage level is lower in reacting response of a medium, the stem cell stimulation condition is stable, and if the voltage changing level is higher, the stem cell stimulation condition is unstable and a considerable loss will be resulted in the differentiation process. In this research, the optimization of electrical stimulation condition is expected for possible stem cell regeneration treatment.

• Textile Coloration and Finishing
• /
• v.30 no.3
• /
• pp.168-179
• /
• 2018

The modified surface of specialty carbon black(SCB) is one of the main technical factors for producing a uniform color and stable dispersion. In this work, the carboxylation or sulfonation process of SCB was used to improve the dispersive properties of hydrophilic solvents such as 1,6-hexanediol and propylene glycol monomethyl ether acetate(PGMEA). The results showed that the color strength of SCB DC2500G changed little with a range of 0.128~0.941(${\Delta}E$) compared to other SCB DC2500G material. In contrast, in the case of SCB EG410, there was a uniform color value with a range of 0.144~0.252(${\Delta}E$). Also, in our experiments, a modified SCB was confirmed by printing ink material as a melt coating paper. It may be possible that the SCB EG410 material can be advantageous as a gravure ink product. Finally, the modified SCB obtained from this research will have a large impact on the industry as a potential material for toners, paint, rubber, fillers, and other carbon black additives.