• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 압출 및 인발 심포지엄
• /
• pp.83-88
• /
• 1999

This study presents development of an software for process and die design of hot extrusion through square dies. The design of extrusion dies is still an art rather than a science with increasing complexity of shape and thinness of section. Therefore, most of the die design is still dependent on personal judgement, intuition and experience. The objective of this study is to develop an software system which includes a design rule extracted from literatures and experts in the extrusion industry. The system also includes finite element simulation program. The developed system is effectively used to design extrusion processes and dies with lead time and trial extrusion.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2000년도 춘계학술대회 논문집
• /
• pp.181-188
• /
• 2000

This paper describes the energy absorption of a square tube under axi compression by using the finite element method. The overall deformations and lo buckling modes of tube was discussed by "plastic hinge concep Force-displacement function was plotted to show various state that depended or time. Also, mean crush load was expressed as a type of section geometry a material property using dimensional analysis. To verify the energy absorption and the effects of dimensions, The standards Wt used as related density and specific energy, mean crushing load and the resL were discussed by the relation between crush load and deformation, the relati between related density and specific energy, the relation between crush load a mean crush load, the relation between mean crush load and specific energy.ergy.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.764-768
• /
• 2001

This study presents development of an software for process and die design of hot extrusion through square dies. The design of extrusion dies is still an art rather than a science with increasing complexity of shape and thinness of section. Therefore, most of the die design is still dependent on personal judgement, intuition and experience. The objective of this study is to develop an software system which includes a design rule extracted from literatures and experts in the extrusion industry. The system also includes finite element simulation program. The developed system is effectively used to design extrusion processes and dies with lead time and trial extrusion.

• 대한기계학회논문집
• /
• 제9권1호
• /
• pp.91-108
• /
• 1985

본 해석에서는 4각단면의 180˚곡관 유동에 PSL법을 도입하는 문제 이외에 .epsilon.방정식에서 생성항의 변화가 유동해석결과에 미치는 영향과 3차원 난류유동의 해석 에 ASM의 도입 필요성에 관해서도 고찰하였다. 모델을 사용하여 흐름의 특성을 구명키로 하였다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1995년도 Proceedings of the Korea Automation Control Conference, 10th (KACC); Seoul, Korea; 23-25 Oct. 1995
• /
• pp.444-447
• /
• 1995

The satellite in a circular orbit about a planet with disturbances and a three-degree-of-freedom (3DOF) structure under seismic excitations are modeled by the linear stochastic differential equations. Then the risk-sensitive optimal control method is applied to those equations. The mean and the variance of the cost function varies with respect to the risk-sensitivity parameter, .gamma.$_{RS}$ . For a particular risk-sensitivity parameter value, risk-sensitive control reduces to LQG control. Furthermore, the derivation of the mean square value of the state and control action are given for a finite-horizon full-state-feedback risk-sensitive control system. The risk-sensitive controller outperforms a classical LQG controller in the mean square sense of the state and the control action.

• 한국전산유체공학회지
• /
• 제19권1호
• /
• pp.57-63
• /
• 2014

This study performed numerical analysis for the characteristics of flow-induced forces and the flow instability depending on the cross-sectional shape of the cylinder in laminar flow. To implement the cylinder cross-section, we adopted an Immersed Boundary Method with marker particles. We analyzed flow characteristics based on the radius of corner curvature. Main parameters are corner radius and Reynolds number (Re). With Re = 40, 50, 150 we calculated the flow field, drag coefficient, RMS of lift coefficient, pressure coefficient and Strouhal number in conjunction with the corner radius variation. Also, we calculated critical Reynolds number ($Re_c$) depending on the corner radius variation.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.771-776
• /
• 2000

Fine grid calculations are reported for the developing turbulent flow in a straight duct and a curved duct of square cross-section with a radius of curvature to hydraulic diameter ratio ${\delta}=R_c/H_H=3.357$ and a bend angle of 180 deg. A sequence of modeling refinements is introduced; the replacement of wall function by a fine mesh across the sublayer and a low Reynolds number second moment closure up to the near wall sublayer in which the non-linear return to isotropy model and the cubic-quasi-isotropy model for the pressure strain are adopted; and the introduction of a multiple source model for the exact dissipation rate equation. Each refinement is shown to lead to an appreciable improvement in the agreement between measurement and computation.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 춘계학술대회 논문집
• /
• pp.86-89
• /
• 2002

Due to extremely large reduction of area or extrusion ratio in ordinary production of extruded profiles, anisotropy is naturally induced by large severe deformation during the extrusion process. Therefore, the anisotropic properties play a great role in the post processing of extruded profiles, such as in bending. Moreover, undesirable deformation will be involved when the deformation-induced anisotropy is ignored. In order to observe the deformation-induced anisotropy of the thin-walled product, the proposed algorithm is applied to some chosen industrial extrusion processes. In the resent work, the method for prediction of deformation-induced anisotropy employing the Barlats six-component yield potential to the rigid-plastic finite element method is proposed. The proposed algorithm is verified with the comparison to the crystallographic texture analysis, and then applied to the C-section exclusion process using a square die. The predicted anisotropy is then compared with the experimental and computational observations for validating the proposed algorithm.

• 한국통신학회논문지
• /
• 제10권2호
• /
• pp.76-81
• /
• 1985

본 논문은 곡선형 사각요소에 대한 기저함수를 제시한 후 이를 이용하여 동축 케이블 및 동축 횡단면 도파관에 대해 유한 요소법을 적용하였다. 동축 케이블의 경우 동일한 수의 요소에 대해 같은 크기보다는 비례의 크기를 갖는 요소에서 더욱 정확한 결과를 얻을 수 있었다. 또한 동축 횡단면 도파관의 경우 차단 주파수는 횡단면의 각도보다는 내, 외경의 변화에 더 큰 영향을 가짐을 확인하였다.

• 소성∙가공
• /
• 제11권8호
• /
• pp.724-730
• /
• 2002

Due to extremely large reduction of area or extrusion ratio in ordinary production of extruded profiles, anisotropy is naturally induced by large severe deformation during the extrusion process. Therefore, the anisotropic properties play a great role in the post processing of extruded profiles, such as in bending. Moreover, undesirable deformation will be involved when the deformation-induced anisotropy is ignored. In order to observe the deformation-induced anisotropy of the thin-walled product, the proposed algorithm is applied to some chosen industrial extrusion processes. In the present work, the method for prediction of deformation-induced anisotropy employing the Barlats six-component yield potential to the rigid-plastic finite element method is proposed. The proposed algorithm is verified with the comparison to the crystallographic texture analysis, and then applied to the C-section extrusion process using a square die. The predicted anisotropy is then compared with the experimental and computational observations for validating the proposed algorithm.