• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.12 no.3
• /
• pp.224-238
• /
• 1987

In the proposed spectrum analyzer, open-loop VCO is replaced with PLL synthesizer incorporating digital frequency synthesizer using modulofunction for measuring precise frequencys. Three different frequency bands and channel spacings are realized by single loop synthesizer through the effective design of the system. The newly designed system with square detection has a good linearity of input range from 10mV to 8.5V, as a result the input sensitivity has been improved up to 500uV. The storage function enables us to analyze not only periodic but also nonperiodic wave-form and zoom-in function expands frequency resolution eight times for the dense spectra.

• Journal of the Optical Society of Korea
• /
• v.16 no.4
• /
• pp.401-408
• /
• 2012

The amplitude error of phase modulator used in closed-loop fiber optic gyroscope has occurred by the temperature dependency of the electro-optic coefficient, and also can be due to the square-wave dither signal which is generally applied for eliminating the deadzone. This error can cause bias drift and scale factor error. This paper analyzes the temperature dependency of the modulation amplitude and the relationship with the scale factor of the gyroscope, and deals with an amplitude control method. The error calculation logic considering the dither signal is implemented on the signal processing module. The result of experiments from a prototype gyroscope shows the effect of the modulation amplitude control and a considerable improvement on performances.

• The Journal of the Acoustical Society of Korea
• /
• v.19 no.2E
• /
• pp.3-7
• /
• 2000

Vibration generated by the non-uniform road profile propagates though each tire and the suspension and finally generates structure born noise in the interior of the passenger vehicle. In this paper, the road-booming-noise which has strong correlation with the vibration signals measured at the suspension system was compensated. Active noise control of the road-booming-noise is rather difficult to achieve because of its non-stationary characteristics. CMFX LMS (Constraint Multiple Filtered-X Least Mean Square) algorithm, which can track non-stationary process rather well, is applied. Comprison of the proposed method and the conventional MFX LMS (Multiple Filtered-X Least Mean Square) algorithm is made through the hardware-in-the-loop simulation and the feasibility of the proposed method is demonstrated with the experiment.

• Proceedings of the KIEE Conference
• /
• 1999.07b
• /
• pp.868-870
• /
• 1999

In this paper we obtain a discrete mathmatical model of a Boiler control system from expermental data, we find appropriate input signal and parameter estimation algorithm for identification of the Boiler control system in power plant. Under these conditions experimental data are collected from real system and parameters are estimated by the Recursive Least Square algorithm. The computer simulation results show the parameter estimation algorithm for identification and the effectiveness of controller design of the Boiler control system.

• 제어로봇시스템학회:학술대회논문집
• /
• 1988.10a
• /
• pp.246-249
• /
• 1988

In this paper, a new design technique which uses weighted least-sqare approach for the solution of the pole assignment problem is represented. This technique maybe used to assign some closed loop poles to places which reduce the large system input and output variance due to near pole-zero condition. The least-square approach is also applied to the design of servo self-tuning controller with integrator.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.5
• /
• pp.478-484
• /
• 1990

An automatic tuning method of a PID controller which is used for single input single output processes is proposed. In the proposed tuning method, the frequency response data model is adopted along with the performance index which is an integral of time weighted square error between reference model and process frequency response data model for tuning. This method is easier to retune when either the process dynamics is changed or the reference model is changed. Finally, an example is provided to show the usefulness of the method.

• Journal of Power Electronics
• /
• v.10 no.5
• /
• pp.451-460
• /
• 2010

This paper presents a new kind of digital control metal halide lamp electronic ballast. A zero-voltage-switch quasi-square-wave (ZVS-QSW) dual Buck converter is adopted here. In this paper, a digital control method is proposed to achieve ZVS for the converter. This ZVS can be realized during the whole working condition. Single-cycle-peak-current control is proposed to solve the problem of excessive inductor current during a low-frequency reversal transient. Power loop control is also realized and its consistency for different lamps is good. An AVR special microcontroller for a HID ballast is used to raise the control performance, and the low-frequency square-wave control method is adopted to avoid acoustic resonance. A 70W prototype was built in the laboratory. Experimental results show that the electronic ballast works reliably. Furthermore, the efficiency of the ballast can be higher than 92%.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.9
• /
• pp.1-8
• /
• 2010

A digital phase wrapping modulation (DPM) open-loop polar transmitter can be efficiently applied to a wideband orthogonal frequency division multiplexing (OFDM) communication system by converting in-phase and quadrature signals to envelope and phase signals and then employing the signal mapping process. This mapping process is very similar to quantization in a general communication system, and when taking into account the error that appears during mapping process, one can replace the coordinates rotation digital computer (CORDIC) algorithm in the coordinate conversion part with the Taylor series approximation method. In this paper, we investigate the application of the Taylor series approximation to the cartesian to polar coordinate conversion part of a DPM polar transmitter for wideband OFDM systems. The conventional approach relies on the CORDIC algorithm. To achieve efficient application, we perform computer simulation to measure mean square error (MSE) of the both approaches and find the minimum approximation order for the Taylor series approximation compatible to allowable error of the CORDIC algorithm in terms of hardware design. Furthermore, comparing the processing speeds of the both approaches in the implementation with FPGA reveals that the Taylor series approximation with lower order improves the processing speed in the coordinate conversion part.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.11 s.353
• /
• pp.141-148
• /
• 2006

This paper deals with the performance improvement by eliminating loop interference signal and inserting adaptive equalizer for phase compensation in OFDMA based Wibro relay station. The Wibro relay station is used for the extension of communication service area and for throughput improvement of base station. The loop interference is important factor of performance determination of relay station when transmitter and receiver is very closely located. In order to design interference canceller, we generated base-band OFDMA signal and then transmitted the signal along with pilot tones alined with two different combinations for training mode. And then, we generated received fading signal due to the loop interference added noise to the received signal. In the receiver, the transmitted signal is recovered by elimination of the interference signal with channel estimate and compensating phase by adaptive equalizer. The performance improvement was verified by computer simulation which show channel estimation, constellation of signal and BER characteristics according to the variation of SNR ratio.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.10
• /
• pp.1147-1158
• /
• 2008

In this paper, we designed a phase-looking circuit that locks the 16.8 GHz VTDRO to a 700 MHz SAW oscillator using SPD as a phase detector Direct phase locking with loop filter alone causes the problem of lock time, so VTDRO is phase leered by loop filter with the aid of time varying square wave current generator. The current generator is related to the loop filter and needs the systematic toning. In this paper, a systematic design of the current generator and loop filter is presented. The fabricated PLDRO shows a stabilized frequency of 16.8 GHz, a output power 6.3 dBm, and a phase noise of -101 dBc/Hz at the 100 kHz offset.