• 한국정보통신설비학회:학술대회논문집
• /
• 2009.08a
• /
• pp.215-218
• /
• 2009

In this paper, Dual-band bandpass filter studied design using Parallel Coupled SIR(Stepped Impedance Resonator). This Dual-band bandpass filter design SIR of half-wavelength by Parallel-coupled type that is available to RFID system and Changed structure in Meander form by size reduce. Because seen Dual-band bandpass filter is designed so that is applicable for frequency 433MHz and 2.45GHz of RFID system is very wide distance between two pass-band, establish 433MHz by fundamental frequency and controlled 2.45GHz by 2st spurious resonance frequency bandstop filter of 1st spurious resonance frequency and Parallel coupled SIR Combine to remove 1st spurious resonance frequency.

• Journal of electromagnetic engineering and science
• /
• v.10 no.1
• /
• pp.1-5
• /
• 2010

A spurious suppressed bandpass filter is proposed and discussed using the stepped impedance resonator(SIR) on a substrate-integrated waveguide(SIW) structure with a double-layer substrate. The second resonance of the fundamental $TE_{10}$ mode can be controlled by adjusting the electrical length and impedance ratio of each SIR. The spurious suppressed SIW bandpass filter shows the measurement results of the insertion loss of 3.98 dB and return loss of less than 11.58 dB at the center frequency of 12 GHz. Also, the second spurious frequency is improved to about $1.5f_0$ compared with $1.33f_0$.

• Journal of electromagnetic engineering and science
• /
• v.5 no.4
• /
• pp.193-196
• /
• 2005

The DC power-bus for the PCB is loaded with metal walls on its selected sides and is characterized electromagnetically. This is a novel concept of approach to mitigate the spurious resonance and finally signal integrity problems. In particular, the peak at DC, which is always in the way to secure parallel-plates' EMC, can be completely removed by the proposed method. Through the findings of this study, the effect of metal-loading of the power-bus will be presented along with the impression that the suggested technique can tackle the headaches of signal integrity, ground bounce, EMIs.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.7
• /
• pp.111-120
• /
• 1996

In this paper, we proposed an inductance loaded small type open-loop travelling wave antenna model for the suitable VHF/UHF frequency bands moisture measurement systems and analyzed its operating characteristics by galerkin's solution method. This antenna model enables to change the oeprating rsonance frequency from the frequency range 150 Mhz to 1.0 Ghz without changing the antenna design dimensions by only varing the load inductance values and it showed the similar operating charcteristics and narrowband resonance characteristics at each resonance frequencies. Also this model showed the uniformly distriubte dpower radiation characteristics above the loop axis and it can effectively suppress the spurious radiations from its narrowband resonance characteristics.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.2
• /
• pp.928-935
• /
• 2018

In this paper, a compact fully printable bandpass filter is suggested for a low-frequency channel 3.2 GHz ~ 3.7 GHz in the Ultra-Wideband (UWB) communication system. It is featured with a small geometry of $0.5{\lambda}_g/15$ and a low insertion loss despite using FR4 as a cheap substrate of a high dielectric loss. This is made possible by generating zeroth-order-resonance (ZOR) from one cell comprising two series resonances obviously separated from one shunt resonance as a third-order bandpass filter. Especially, the series resonance elements are combined with spur-lines bent by 90 degrees, which makes the port-impedance matched well and eliminates spurious hikes in the stopband, while the overall size remains almost unchanged. The design is carried out by setting up the equivalent circuit and the circuit simulation is checked by the full-wave EM analysis. The structure is manufactured and measured to show that the circuit modeling and EM simulation results agree with the measured data.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.8
• /
• pp.41-46
• /
• 2008

This paper conducts the research on the variation in the characteristics of the resonance and impedance of the metallic parallel plates due to the replacement of the normal dielectric substrate by the metamaterial. The ENG(${\epsilon}<0$), MNG(${\mu}<0}$) and DNG(${\epsilon},{\mu}<0$) types of metamaterial as well as the DPS(Double Positive) material are taken into consideration a full-wave modal analysis method known for accurate computation, as the SRR-kind of Lorentz model for permittivity and metal wire-periodic array-kind of Drude model for permeability, and the behaviors of parallel plates' resonance mode and impedance are observed. Based upon the observation, the design guidelines for the substrate can be addressed regrading how to suppress the parallel plates' spurious resonance modes that degrade the quality of the electronic equipment.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.11
• /
• pp.1728-1735
• /
• 1989

A design procedure for microstrip bandpass filters using step impedance resonators (SIR's) and tapped input/output to a conventional parallel coupled line bandpass filter is presented. The filter configuration consisting of both half-wavelength and SIR's suppreses to spurious resonance response near the second harmonics, while tapping techniques offer benefit in situations where the impractical. The measured frequency responses of the designed filter are in close agreement with the computed responses.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.2
• /
• pp.95-101
• /
• 2008

This paper presents a novel bandpass filter design method for suppressing spurious response in the GSM band and effectively reducing the overall size with the unbalanced-conditioned metamaterials. Compared to the conventional bandpass filters based on half-or quarter-wave resonators, the CRLH(composite right/left-handed) bandpass filter works excellently in harmonic-suppression by 40$\sim$50 dB and 80 %-miniaturization using the zero-order resonators bridged by Inductive-coupling Inverters suggested first time. The proposed technique, with the equivalent circuit and dispersion diagram, is validated by performance predictions and experiments.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.4 no.3
• /
• pp.182-188
• /
• 2004

We demonstrate a $2.1\;{\times}\;1.0\;{\times}\;0.1cm^3$ sized compact transmitter using LTCC System-in-Package (SiP) technology for 60GHz-band wireless communication applications. For low-attenuation characteristics and resonance suppression of the SiP, we have proposed and demonstrated a coplanar double wire-bond transition and novel CPW-to-stripline transition integrating air-cavities as well as novel air-cavities embedded CPW line. The fabricated transmitter achieves an output of 13dBm at a RF frequency of 62GHz, an IF frequency of 2.4GHz, and a LO frequency of 59.6GHz. The up-conversion gain is 11dB, while the LO signal is suppressed with the image rejection mixer below -21.4dBc, and the image and spurious signals are also suppressed below -31dBc.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2000.11a
• /
• pp.95-98
• /
• 2000

Film bulk acoustic resonator used in microwave region can be analyzed by one-dimension Mason's model and one-dimensional numerical method, but it had several constraints to analyze effects of area variation, electrode-area variation, electrode-shape variation and spurious characteristics. To overcome these constraints film bulk acoustic resonator must be analysed by three dimensional numerical method. So, in this paper three dimensional finite element method was used to analyze several moles of resonance and was compared with the one dimension Mason's model analysis and analytic solution.