• 설비공학논문집
• /
• 제22권1호
• /
• pp.33-39
• /
• 2010

The film boiling heat transfer was experimentally investigated for the water sprays impacting on an inclined hot surface. Full cone spray nozzles were employed for the spray cooling experiment, and experiments were made for different inclination angles of $\theta=0^{\circ}$, $15^{\circ}$, $30^{\circ}$ and $45^{\circ}$. The experimental results show that, in the downstream region of the inclined hot surface, increasing the inclination angle increases the local heat flux slowly because of increasing the number of rebound droplets. However, the inclination angle of heat transfer surface had no remarkable effect on the local heat flux of spray cooling under the present test conditions.

• 한국분무공학회지
• /
• 제2권1호
• /
• pp.46-51
• /
• 1997

In this study, spray characteristics of the pressure swirl atomizer have teen investigated. Four atomizers with the different orifice diameter and five tangential ports with the different inlet number were fabricated. For the purpose of the measurement of the mean drop sine, Malvern particle sizer was used. And also discharge coefficient was measured and spray cone angle was measured by using shadow graphy method. As a result when the injection pressure was increased, mean drop size was decreased. And the dominant factor which influence on the spray characteristics of pressure swirl atomizer was orifice diameter.

• 대한기계학회논문집B
• /
• 제22권11호
• /
• pp.1625-1634
• /
• 1998

The objective of this study is to establish geometric guidelines for design of impaction parts prepared for removing undesirable effects of fuel deposition on a wall in small direct-injection diesel engines. In order to get the guidelines a new wall geometry is introduced and assessed, which has a flat top and a slant edge. The size of the flat top and the angle of the slant edge are varied and tested in same chamber condition, then their effects on spray dispersions and drop sizes are discussed. The results show that the case of 3.0mm flat top and $60^{\circ}$ edge angle gives the best spray characteristics for a small combustion chamber in the test conditions chosen in this paper.

• 한국항공우주학회지
• /
• 제34권7호
• /
• pp.97-104
• /
• 2006

분사조건과 주위기체 압력에 따라 스월 인젝터의 분무각과 분열길이를 측정함으로써, 스월 인젝터의 분무 및 분열특성에 대한 연구를 수행하였다. 분사조건으로 축방향 We 수(Wel)를 1554까지 주위기체 압력을 4.0MPa까지 증가시켰다. Wel과 주위기체 밀도(ρ)가 증가함에 따라 공기역학적 힘이 증가하여 원추형 액막 표면의 교란이 증가하게 되고, 따라서 분열이 빨리 일어난다. 결과에 따르면 주위기체 밀도에 따른 분무각의 변화가 분열이 일어나기 전과 후가 다르게 나타났다. 분열이전에는 분무각이 주위기체 밀도 변화에 관계없이 거의 일정하였으나, 분열이 일어나게 되면 분무각이 감소하게 된다. 또한 측정된 분열길이를 선형불안정이론과 비교해 보았는데, 액막두께의 감쇠를 고려한 수정된 이론이 측정결과와 상당히 유사한 결과를 얻을 수 있었다.

• 한국분무공학회지
• /
• 제8권1호
• /
• pp.29-36
• /
• 2003

Spray characteristics on diesel- water emulsion are analyzed in high pressure injection for several variables such as water content, injection pressure. Spray Patterns were visualized under various water content and injection pressures. Spray tip penetration was increased and spray angle decreased in accordance with increasing of water content. But these characteristics were enhanced with increase of injection pressure to high pressure.

• 한국자동차공학회논문집
• /
• 제11권3호
• /
• pp.58-64
• /
• 2003

Dimethyl Ether(DME) has been considered as one of the most attractive alternative fuels for compression ignition engine. Its main advantage in diesel engine application is high efficiency of diesel cycle with soot free combustion though conventional fuel injection system has to be modified due to the physical properties of DME. Experimental study of DME and conventional diesel spray employing a common-rail type fuel injection system with a 5-hole sac type injector was performed in a constant volume vessel pressurized by nitrogen gas. Spray cone angles and penetrations of the DME spray were characterized and compared with those of diesel. For evaluation of the evaporating characteristics of the DME, shadowgraphy technique employing an Ar-ion laser and an ICCD camera was adopted. Tip of the DME spray was formed in mushroom-like shape at atmospheric chamber pressure, which disappeared in higher chamber pressure. Spray tip penetration and spray cone angle of the DME became similar to those of diesel under 3MPa of chamber pressure. Higher injection pressure provided wider vapor phase area while it decreased with higher chamber pressure condition.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권3호
• /
• pp.320-327
• /
• 2002

An experimental study of heat transfer from hot flat surface to water sprays was conducted in high temperature region. Heat transfer measurements for hot flat surface were made by 4 sheathed C-A thermocouples. Droplets volume flux were also measured-independently at a position in spray field. The test conditions included variations in droplets volume flux, subcooling of cooling water of $1.565\times10^{-3} to 14.089\times10^{-3}m^3/m^2s and 80 to $20^{\circ}C$ respectively. The effects of inclination angle on heat transfer were investigated and changes in inclination angle of hot flat surface affected heat transfer coefficients of high temperature region.

• 한국자동차공학회논문집
• /
• 제11권1호
• /
• pp.87-94
• /
• 2003

Recently, LPLi(Liquied-Phase LPG injection) system is studied for the new stringent emission regulations. But , there are some problems to be solved such as injector tip icing and fuel leakage for LPLi system development. In this paper, the icing problem near injector tip which leads to difficulty of accurate A/F control was studied and reported. Icing of injector tip and port wall was observed at all the cases in this study regardless of injection duration and angle, air humidity change. The spray angle of LPLi was observed approximately two times wider than that of Gasoline injection. This makes the LPLi spray collide with intake port around injector tip. Temperature of the wetted area was decreased and icing of water vapor contained in intake air because of evaporation of the fuel film. The ice of the injector tip and port wall is also affected by the materials related to heat transfer.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1534-1539
• /
• 2004

The objective of this study is to simulate the etching characteristics with oscillation angle for the optimization of etching system. The etching characteristics were analyzed under different etching conditions. The spray characteristics were measured by Phase Doppler Anemometer (PDA). The correlation between the spray characteristics and the etching characteristics was investigated and used for fundamental data to simulate the etching characteristics with oscillation angle. The smaller coefficient of variation, the more uniform etching characteristic distribution became. It was found that numerical predictions of etching factor generally agreed well with the measured results with distance from nozzle tip. Oscillation leads to decrease of etching factor and increase of uniformity.

• 한국분무공학회지
• /
• 제1권1호
• /
• pp.21-27
• /
• 1996

This experimental study was to investigate spray angles and drop sizes in an external mixed twin-fluid swirl jet nozzle. Twin-fluid swirl jet nozzle with swirlers designed four swirl angles such as $0^{\circ},\;22.5^{\circ},\;45^{\circ},\;64.2^{\circ}$ was employed. A PDA system was utilized for the measurement of drop size and mean velocity. Water and air were used as the working fluids in this experiment. The mass flow rate of water was fixed as 0.03 kg/min, and air flow rates were controlled to have the air/liquid mass ratio from 1.0 to 6.0. As a result, swirl angle controlled to spray angles and drop sizes. It was found that swirl angle was increased with spray angle and with decreased SMD. However, the effect of swirl angle was reduced at large air/liquid mass ratio(Mr=6.0).