• Korean Chemical Engineering Research
• /
• v.48 no.5
• /
• pp.660-667
• /
• 2010

In this research polyimide, Matrimid 5218, hollow fiber membrane was used to recover sulfur hexafluoride($SF_6$) which is one of the six greenhouse gases from $N_2/SF_6$ mixture gas. Fibers were spun from using dry-wet phase inversion method. The module was manufactured by fabricating fibers after surface coating with silicone elastomer. The scanning electron microscopy(SEM) studies showed that the produced fibers typically had an asymmetric structure; a dense top layer supported by a sponge-like substructure. The developed module had a permeance of 0.78-1.36 GPU for $N_2$ with $N_2/SF_6$ selectivity of 2.44-5.08 at various pressure and temperature. For recovery of $SF_6$, a membrane module and 10 vol.% $SF_6$ from $N_2/SF_6$ mixture gas was used. The effects of various operating condition such as pressure, temperature, and retentate side flow rate were tested. When pressure and temperature were increased and retentate flow rate was decreased, the $SF_6$ purity in recovered gas was increased up to 37.5 vol.% with decreasing recovery ratio. When retentate flow rate was increased pressure and temperature was decreased, the $SF_6$ recovery ratio in retentate side was increased up to 89% with decreasing the $SF_6$ purity in retentate side.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.46 no.3
• /
• pp.221-228
• /
• 2001

This study was carried out to investigate the effect of germination condition and drying temperature on growth and physicochemical properties of brown rice. Three brown rice seeds of Ilpumbyeo, Dasanbyeo and Heugjinjubyeo were stored at room temperature for six weeks to test the time-sequence germination viability. Relatively stable germination ratio was maintained until 2 weeks after storage. However, 3 weeks after storage, germination ratio of brown rice seeds started to decrease rapidly and their germination ratio was lower than 80%. For this reason, brown rice was recommended for seeding within 2 weeks after hulling. During the initial 5 days, germination ratio of 24 hours pre-soaking brown rice was higher about 2-3% than that of non-soaking brown rice. The $25^{\circ}C$ was considered as the most favorable temperature for brown rice germination, because of the high germination ratio and desirable coleoptile growth of the brown rice, and little seed rotting symptoms. The scanning electron micrographs showed the structural differences between hot-air dried and freeze dried germinated-brown rice kernel. In the freeze dried germinated-brown rice, seed coat (pericarp, tegmen and aleurone layer) was mechanically disrupted from the endosperm, and many cleavages were observed among starch storing cells and starch granules. The endosperm of freeze-dried brown rice kernels formed the sponge-like structures and showed the fragile traits. For this reason, hot-air drying is considered as more suitable method than freeze drying for germinated-brown rice. The crude protein and amylose contents were slightly changed, but there were no significant differences during the germination period. Crude fiber content was decreased, but crude Int and total amino acid contents were increased as seeding days increased. A rapid increase in $\alpha$-amylase activities of germinating brown rice was observed at S days after seeding, and $\alpha$-amylase activities were decreased from 8 days after seeding. Total free sugar contents were decreased during the germination period. There was continuous decline in the contents of sucrose and glucose until 8 days after seeding, but fructose and maltose content were gradually increased from the 5 days after seeding.

• Korean Chemical Engineering Research
• /
• v.49 no.2
• /
• pp.250-255
• /
• 2011

In this study, by using the polymeric membrane separation process, the $CO_{2}/CH_{4}$ separation and $H_{2}S$ removal from biogas were performed in order to $CH_{4}$ purification and enrichment for the fuel cell energy source application. Fibers were spun by dry/wet phase inversion method. The module was manufactured by fabricating fibers after surface coating with silicone elastomer. The scanning electron microscopy(SEM) studies showed that the produced fibers typically had an asymmetric structure; a dense top layer supported by a porous, sponge substructure. The permeance of $CO_{2}$ and $CO_{2}/CH_{4}$ selectivity increased with pressure and temperature. Mixture gas with increasing pressure and temperature, removal efficiency of the $CO_{2}$ and $H_{2}S$ were decreased while concentration of $CH_{4}$ was increased up to 100%. When retentate flow rate was increased with the decreasing of pressure and temperature the $CH_{4}$ recovery ratio in retentate side was increased while the $CH_{4}$ purity in retentate side was decreased.

• 보존과학연구
• /
• s.33
• /
• pp.99-108
• /
• 2012

The white-rot fungus (Trametes versicolor) and brown-rot fungus (Tyromyces palustris), which cause damage to a variety of wooden cultural properties and buildings, such as drying of the wood tissue, decay and cracks, sponge, and discoloration, give rise to serious structural and aesthetic problems. Moreover, pest termites (Reticulitermes speratus kyushuensis Morimoto) can cause damages like hollowing the outdoor beams or pillars of wooden buildings and finally causing such buildings to collapse due to the termites' destruction of the inside of the beams or pillars, leaving only a thin layer on their surfaces. This study was conducted to determine the impact of the wood-decay fungus, a representative damage-causing microorganism, and of insects and termites on the termite ecology. The damage ratio was calculated as the weight of the timber, and the overall total mass was reduced from two kinds of rot fungi. The white-rot fungi reduced the total wood mass, but the brown-rot fungi were observed to have had an increasing tendency to do so. The wood mass was measured after drying to determine the destruction capacity of termites. As a result, the wood mass consumed by the brown-rot fungi was shown to be greater.

• Membrane Journal
• /
• v.8 no.3
• /
• pp.157-169
• /
• 1998

The effects of solvents (DMAc, NMP, 1,4-dioxane) and nonsolvents ($H_2O$, Methanol, n-hexane) on the morphology of 6FDA-p-TeMPD polyimide membrane, prepared by the wet phase inversion method, were studied. In the polymer/solvent/nonsolvent ternary system, the binodal curve, the coagulation value and the relative light transmission were measured, and the solubility parameter difference was calculated. The onset state and rate of liquid-liquid alemixing were predicted and the morphology of membrane was analyzed. It is found that the finger-like pores are formed within discontinuous polymer nodules when the binoclal curve is close to the polymer-solvent (P-S) axis, the coagulation value is small, the reduction of light transmission is easy to occur and the order of solubility parameter difference ($\Delta \delta_{i-j}$) is $\Delta \delta_{S-NS} > \Delta \delta_{P-NS} > \Delta \delta_{P-S}$. The dense skin with small nodules and the sponge type sublayer with macrovoid are formed in the case that the binodal curve is distant from the P-S axis, the onset time of liquid-liquid demixing is long and the order of $\Delta \delta_{i-j}$ is $\Delta \delta_{P-NS} >(\Delta \delta_{S-NS} < > \Delta \delta_{P-S})$. The thick layer of fine nodule coagulation and loosely grown sublayer of nodules appear when the binodal curve is distant from the P-S axis, the onset time of liquid-liquid demixing is very long and the order of $\Delta \delta_{i-j}$가 $\Delta \delta_{S-NS} > (\Delta \delta_{P-NS}$\lessgtr$ > (\Delta \delta_{P-NS} < >)\Delta \delta_{P-S}$ ).

• Polymer(Korea)
• /
• v.32 no.3
• /
• pp.199-205
• /
• 2008

In this study, we fabricated poly (lactide-co-glycolide) (PLGA) scaffold modified with small intestinal submucosa (SIS) as a drug delivery matrix of bioactive molecules. SIS derived from the submucosa layer of porcine intestine has been widely used as biomaterial because of low immune response. PLGA scaffold was prepared by the method of solvent casting/salt leaching. Novel composite scaffolds of SIS/PLGA were manufactured by simple immersion method of PLGA scaffold in SIS solution under vacuum. SEM observation shows that PLGA and SIS/PLGA scaffolds have interconnective and open pores. Especially, SIS/PLGA scaffold showed that micro-sponge of SIS with interconnected pore structures were formed in the pores of PLGA scaffold. In order to assay release profile of proteins, we manufactured FITC conjugated BSA loaded PLGA and SIS/PLGA scaffold. And the release amount was identified by fluorescence intensity using the fluorescence spectrophotometer. The initial burst of BSA containing SIS/PLGA scaffolds was lower than that of PLGA scaffolds resulting in constant release. And release of BSA in SIS/PLGA scaffold was fast and incremental because of the increased content of BSA. In conclusion, we confirmed that penetrated SIS solution prevented the initial burst of BSA and PLGA modified with SIS scaffold is useful as protein carriers with controlled release pattern.