• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.28 no.1
• /
• pp.21-26
• /
• 1992

Generally a navigator evaluated the maneuverability of his ship by the scale of turning circle which was described only by the largest rudder angle of the port and starboard sides. But to have the sufficient knowledge of his ship's maneuvering characteristics he should consider the data about the new course keeping test, the spiral test, and the turning circle tests in accordance with the rudder angles together. In this paper the author performed the above tests to study the maneuverability of the stern trawler M.S. Pusan 404 which is a training ship of the National Fisheries University of Pusan. The obtained results are summarized as follows: 1. When the rudder angles being 5。, 10。, 20。, 30。, 35。 the advances of the starboard side turning circles were 12.8, 8.2, 4.8, 2.9, 2.7 times as large as the length of the ship, and of the port side turning circles were 13.3, 8.7, 5.4, 3.5, 2.9, time as large as the large as it. Under the same conditions the tactical diameters were 15.1, 9.7, 5.2, 3.1, 2.8 times as large as the length of the ship, for starboard side, and 17.2, 12.4, 6.4, 3.7, 3.2 times as large as it for port side. 2. As the rudder angle being increased the ratio of the advance to the tactical diameter was nearly 1 and her obeying ability was better than that of the small angle. 3. The mean values of the rates of speed reduction during the steady turning motion were 0.96, 0.92, 0.82, 0.71, 0.65 in accordance with the rudder angles. 4. The relative formulas between the distance to the new course y and the altering course x were as follows: When rudder angles being 10。, 20。, 30。, y=52.2222+1.6133x, y=48.750+0.9383x, y=39.250+0.655x respectively. 5. There was little difference of the distance to the new course between rudder angle 20。and 30。, and so it is desirable for a navigator to a navigator to use the small rudder angles unless sudden emergencies. 6. Though her rudder angle being small her course stability was good according to the spiral tests.

• Proceedings of the KSRS Conference
• /
• 2005.10a
• /
• pp.501-504
• /
• 2005

In general, most incomplete communication link setup between satellite and ground station right after separation from launcher come from less accurate orbital vector ground station uses to track the satellite because only predicted orbital state vector is available during first few orbits. This paper describes the developed procedure for successful initial acquisition for KOMPSAT-2 using scanning functions ofK13 antenna system with predicted orbital information. Azimuth scan, raster scan, spiral scan functions were tested with KOMPSA Tl under intentionally degraded orbital information for antenna operation. Through tests, spiral scan function was decided to be best search scan among 3 scans. Developed procedure can assure the successful acquisition only if azimuth offset and time offset value are within +/-2deg and +/-30sec, respectively.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.4
• /
• pp.417-424
• /
• 2007

This paper presents a solution that an analytical model for an induction motor and the formula of regenerative power and instantaneous torque are derived. based on the spiral vector. The torque is controlled linearly through variations of the slip angular velocity, based on the field acceleration method (FAM). And also PWM inverter fed induction motor drives is schemed to be easily a regenerative drive. The voltage source inverter fed induction motor drives that regenerative power occurs with back current type is presented, to easily controlled the feedback power and to proper the adaption of energy shaving drives. The experimental tests verify the performance of the FAM, proving that food behavior of the drive is achieved in the transient and steady state operating condition, and are discussed to save the power that regenerative power is measured at the operating acceleration or deceleration of servo system.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.7
• /
• pp.55-61
• /
• 2014

The need of geothermal energy is constantly increasing for economical and environmental utilization. Horizontal ground heat exchangers (GHEs) can reduce installation cost and increase efficiency. There are many kinds of GHEs, and it is known that slinky and spiral coil type GHEs show high thermal performance. Therefore, this paper presents experimental results of heat exchange rates in horizontal slinky and spiral coil type GHEs installed in a steel box whose size is $5m{\times}1m{\times}1m$. Dried Joomunjin standard sand was filled in a steel box, and thermal response tests (TRTs) were conducted for 30 hours to evaluate heat exchange rates by changing different pitch spaces of horizontal slinky and spiral coil type GHEs. As a result, spiral coil type GHE showed 30~40% higher heat exchange rates per pipe length than horizontal slinky type GHEs. Furthermore, long pitch interval (Pitch/Diameter=1) showed 200~250% higher heat exchange rates per pipe length than short pitch interval (Pitch/Diameter=0.2) in both spiral coil and horizontal slinky type GHEs, respectively.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.1
• /
• pp.48-58
• /
• 2014

In this study, quasi-static according to the displacement-controlled (strain control) method tests on RC columns for seismic reinforcement performance in accordance with the provisions of the seismic design and construction before 1992 design code for highway bridges in korea. Used reinforcement that improves the performance of Inorganic Helical Bar, a kind of alloy steel, circular columns were tested outside the seismic reinforcing. In the experiment, fracture behavior, lateral load-displacement relation, ductility and energy assessment evaluation was performed through tests. The variables in experimental are section force of reinforcement, spiral reinforcement spacing, reinforcement method. Improved seismic performance and effect were confirmed through quasi-static test experiments. The results of study confirmed determination the appropriate size of reinforcement, reinforcement forces, spacing and selection of the type required, furthermore, not only mechanical reinforcement but also substitution of high-strength concrete reinforced with concrete cover improved seismic performance.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.6
• /
• pp.685-691
• /
• 2005

In this study, high performance waste heat recovery heat exchanger was developed using the bayonet tube with spiral serrated fins. Especially, heat exchanger of the bayonet tube type was operated well because of double water passes mechanism and characteristics. A cooling water Passes down inner tubes to thimble-form tubes, then flows back up as it boils. The heat exchanger of bayonet tube type was composed of steel tube with 7channels$(I.D_1\;14mm.\;I.D_2\;31.6mm)$ and spiral serrated fins. The performance tests were conducted under the following conditions A cooling water flow rate was 273kg/h and engine l·pm was varied from 750rpm to 3500 rpm. From the experimental result. waste heat recovery was 9.21kW when engine rpm was 3500. and pressure drop was $15\~260mmHg/m^3$ The effectiveness of heat exchanger was about /$0.7\~0.9$. The performance of heat exchanger was evaluated by using the $\varepsilon-NTU$ method. In the study the NTU of the heat exchanger was $1.57\~2.33$.

• Steel and Composite Structures
• /
• v.20 no.6
• /
• pp.1259-1274
• /
• 2016

A precast composite column system has been developed in this study by utilizing multi interlocking spiral steel into a centrifugally-formed hollow-core precast (CHPC) column. The proposed hybrid column system can have enhanced performances in the composite interaction behavior between the hollowed precast column and cast-in-place (CIP) core-filled concrete, the lap splice performance of bundled bars, and the confining effect of concrete. In the experimental program, reversed cyclic loading tests were conducted on a conventional reinforced concrete (RC) column fabricated monolithically, two CHPC columns filled with CIP concrete, and two steel-reinforced concrete (SRC) columns. It was confirmed that the interlocking spirals was very effective to enhance the structural performance of the CHPC column, and all the hollow-core precast column specimens tested in this study showed good seismic performances comparable to the monolithic control specimen.

• Journal of the Society of Naval Architects of Korea
• /
• v.50 no.4
• /
• pp.199-205
• /
• 2013

To research and develop an azimuth thruster, the new type of open water test dynamometers to measure thrust, torque, total thrust and duct force are designed and manufactured by Samsung Ship Model Basin(SSMB). A compact servomotor to be accurately controlled is connected to precise spiral bevel gear through shafting system combined by couplings and main shafts. The dynamometers have shown excellent linearity and repeatability for all components of forces and a torque. Also, the open water tests have been successfully performed to show the performance of the system. In near future, it is expected that the device can be used for the study of scale effects and development of azimuth thrusters.

• Korean Journal of Microbiology
• /
• v.25 no.3
• /
• pp.238-243
• /
• 1987

In this study, an acidoduric Streptomyces strain was isolated and identified from acidic forest soil around Dankook University, Cheonan Campus. This isolated strain had rod-shaped, smooth, non-motile spore and the shape of spore chain was compact spiral. This structure appeared similar to the sporangium of the genus Streptosporangium but this strain proved to be a Streptomyces strain by an electron microscopic study and cell wall analysis. This strain showed a best growth on neutral medium, was also able to grow on the acidic media of pH 4.0 and pH 5.0. The color determination of this strain on various agar media and other physiological tests were carried out by ISP-methods. From these results, the isolated strain was considered to be Streptomyces mirabilis.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.53 no.2
• /
• pp.177-186
• /
• 2017

This study is intended to provide navigator with specific information necessary to assist in the avoidance of collision and in operation of ships to evaluate the maneuverability of research vessel Jera. Authors carried out full-scale sea trials for turning test, zig-zag test, and spiral test at actual sea-going condition, which were performed on starboard and port sides with 10-20 rudder angle at service speed of 10 knots. The turning circle was much different at both of the turning of port and starboard which was longer at the starboard than at the port. In the zig-zag test results, the port and starboard was $10^{\circ}$ the first and second overshoot angles were $6.0^{\circ}$, $5.8^{\circ}$ and $6.3^{\circ}$, $7.1^{\circ}$ respectively and the first overshoot angles were $16.4^{\circ}$, $17.6^{\circ}$ when using $20^{\circ}$. Her maneuverability index T and N can be easily determined by using an analogue computer with the data obtained from the zig-zag tests where K is a constant representing the turning ability and T is a constant representing her quick response. In the zig-zag tests under $10^{\circ}$ or $20^{\circ}$ at rudder angle, the value K is 0.149. 0.123 sec- and T is 11.853 and 6.193 sec and angular velocity is $0.937^{\circ}/sec$ and $1.636^{\circ}/sec$. In the spiral test, the loop width was unstable at $+0.51^{\circ}$ and $-1.19^{\circ}$ around the midship of rudder, but the tangent line at $0^{\circ}$ was close to vertical. From the sea trial results, we found that she did comply with the present criterion in the standards of maneuverability of IMO.