• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 춘계학술대회논문집; 경주코오롱호텔; 22-23 May 1997
• /
• pp.160-166
• /
• 1997

The spindle motor in a computer hard disk drive can be modeled as a rotor-bearing system supported by the base plate. Ball bearing is the crucial element to determine the stiffness of the spindle motor, and its design parameters and operating conditions determine the dynamic characteristics of the spindle motor. In the analysis of a rotor-bearing system with a short shaft like a spindle motor, the stiffness of the base plate as well as ball bearings must be considered accurately to analyze the dynamic charateristics of a spindle motor. In this paper, the lateral and the axial vibration of the spindle motor were analyzed by the transfer matrix method for the dual-shaft rotor-bearing model and by d.o.f lumped parameter model, respectively. The simulation results had good agreements with the experimental modal testing. The dynamic characteristics were fully investigated for the change of the major design parameters of the spindle motor, i.e. the preload of ball bearings and the rotational speed.

• 연구논문집
• /
• 통권31호
• /
• pp.77-88
• /
• 2001

In this paper, the critical vibration limits of a spindle unit for a high speed ball pen tip processing machine are studied. The vibration of the spindle is measured by FFT, and the influence of the vibration amplitude due to unbalance, bearing deflect, bite, and timing belts tension is analyzed. The critical vibration limits of the spindle is determined by the X, and Z directional vibrations of the spindle. Both FET and RMS values can be used to analyze the vibration characteristics of the spindle. From experimental results the limit line can be drawn for the spindle. The RMS value for the vibration limit is 3 G.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.784-789
• /
• 2000

Equations of motion are derived and solved using the finite element method substructure synthesis for the disk-spindle system with rigid spindle and flexible shaft. The disk is modeled as a flexible spinning disk by Kirchhoff plate theory and von Karman nonlinear strain. The spindle supporting the flexible disk is modeled as a rigid body to consider its complex geometry. The stationary shaft supporting the rotating disk-spindle-bearing system is modeled by Euler beam, and the ball bearings are modeled as the stiffness matrix with 5 degrees of freedom. Developed theory is applied to analyze the vibration characteristics of a 3.5" HDD and a 2.5" HDD, respectively, and modal tests are performed to verify the simulation results. This paper shows that the developed theory can be effectively applied to the rotating disk-spindle system with the spindle of complex shape.

• 한국정밀공학회지
• /
• 제14권10호
• /
• pp.15-27
• /
• 1997

Quasti-static cutting force variations in milling process are measured indirectly using spindle motor current. Quasi-static sensitivity of the spindle motor current is higher than that of the feed motor current. Magnitude of the spindle motor current is independent of cutting direction. The linear relationship between the cutting force and the spimdle motor RMS current at various spindle rotational speed is obtained. Frequency/ Voltage(F/V) converter voltage is measured to identify the spindle speed and to determine the cutting force at various spindle speeds. Overload on the tool during milling process can be detected using the proposed indirect cutting force measurement. Based on these measurements, cutting force is regulated at a constant level by feedrate control.

• International Journal of Precision Engineering and Manufacturing
• /
• 제6권1호
• /
• pp.51-58
• /
• 2005

The development of the high-efficiency machine-tools equipment and new cutting tool materials with high hardness, heat- and wear-resistance has opened the way to application of high-speed cutting process. The basic argument of using of high-speed cutting processes is the reduction of time and the respective increase of machining productivity. In this sense, the spindle units may be regarded as one of the most important units, directly affecting many parameters of high-speed machining efficiency. One of the possible types of spindle units for high-speed cutting is the air-bearing type. In this paper, we propose the mathematical model of the dynamic behavior of the air-bearing spindle. To provide the high-level of speed capacity and spindle rotation accuracy we need the adequate model of "spindle-bearings" system. This model should consider characteristics of the interactions between system components and environment. To find the working characteristics of spindle unit we should derive the equations of spindle axis movement under the affecting factors, and solve these equations together with equations which describe the behavior of lubricant layer in bearing (bearing stiffness equations). In this paper, the three influence coefficients are introduced, which describe the center of spindle mass displacement, angle of shaft rotation around the axes under the unit force application and that under the unit torque application. These coefficients are operated in the system of differential equations, which describes the spindle axis spatial movement. This system is solved by Runge-Kutta method. Obtained trajectories and amplitude-frequency characteristics were then compared to experimental ones. The analysis shows good agreement between theoretical and experimental results, which confirms that the proposed model of air-bearing spindle is correctis correct

• 한국정밀공학회지
• /
• 제26권7호
• /
• pp.120-126
• /
• 2009

Thermal displacement of high speed spindle is very important problem to be solved. To solve heat generation and thermal displacement problems that influence on the product accuracy, it is very important to predict thermal characteristics of the spindle and it is positively necessary to select the conditions of cooling, flow rate and preload of bearings. In this paper, 30,000rpm($1.455{\times}10^6DmN$) spindle was designed and produced. The analysis of thermal deformation for heat generation of inner spindle was carried out using commercial program $ANSYS^{(R)}$ and the result was compared with measured data using $LabVIEW^{(R)}$ and SGXI-1600, 1125 and 1126 module. Temperature distribution and thermal displacement according to spindle speed are measured. Using this method, it is possible to predict and to improve thermal characteristic of high speed spindle by control spindle speed, bearing preload and cooling rate.

• 연구논문집
• /
• 통권27호
• /
• pp.127-139
• /
• 1997

투포원 연사기는 스핀들 1회전에 2회의 꼬임을 부가하여 실의 신축성과 인장강도 및 내마모성을 증가시키며, 특수한 목적의 의장사를 만드는 섬유기계이다. 스핀들 유니트는 고속 회전중에 안정화된 운동이 지속되도록 구조설계가 요구되는 핵심장치로서 스핀들 유니트의 동특성 해석은 고속 스핀들 유니트설계의 최적화를 도모할 수 있을 것이다. 스핀들 유니트는 블레이드와 로타리 디스크로 구성되어 있으며, 스핀들 축에 대하여 회전체 형상을 유지 하고 있다. 동특성 해석을 수행하기 위하여 전달 매트릭스 해석법을 정의하고 해석용 프로그램인 SPINDLE을 이용하여 비틀림과 굽힘 고유진동수를 해석하였으며, 운전회전수에서 변위모우드를 분석하였다.

• 한국소음진동공학회논문집
• /
• 제19권11호
• /
• pp.1214-1221
• /
• 2009

A high-speed spindle can be very sensitive to rotating mass unbalance which has harmful effect on many machine tools. Therefore, the balancing procedure to reduce vibration in rotating system is certainly needed for all high-speed spindles. So, balancing procedure was performed with a spindle-bearing system for CNC automatic lathe by using numerical procedure. The spindle is supported by the angular contact ball bearings and the motor rotor is fixed at the middle of spindle. The spindle-bearing system has been investigated using combined methodologies of finite elements and transfer matrices. The balancing was performed through influence coefficient method and the comparison was made by whirl responses between before balancing and after balancing. As a result, balancing of simple spindle model reduced whirl orbit magnitude in case of a completely assembled spindle model.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.456-459
• /
• 2008

In the field of yarn dyeing, the most generally employed method is a type of package dyeing which uses a package cheesesstacked on a spindle made of a perforated tube. Spindles up to now, have been designed without considering the characteristics of dyeing liquid, focusing only on the geometric configuration which cause many problems such as lack of level dyeing. To improve the level dyeing and find the appropriate spindle configuration for the most effective dyeing process, this study examines the spindle flow-field in detail, using a computational method. Flow characteristics inside the spindle have been investigated with varying in porosity, porous diameter and the velocity of the flow. The results show that the total pressure of the flow through the spindle is used to overcome body force. The characteristics of the flow from the porous spindle could also be observed. Based on the results from this study, an effective spindle configuration for level-dyeing has been proposed.

• 한국기계가공학회지
• /
• 제11권4호
• /
• pp.104-110
• /
• 2012

The spindle with a built-in motor can be used to simplify the structure of machine tool system, while the rotor has unbalance mass inevitably. A high-speed spindle can be very sensitive to rotating mass unbalance which has harmful effect on many machine tools. Therefore, the balancing procedure to reduce vibration in rotating system is certainly needed for all high-speed spindles. So, it was performed with a spindle-bearing system for CNC automatic lathe by using numerical procedure. The spindle is supported by the angular contact ball bearings and the motor rotor is fixed at the middle of spindle. The spindle-bearing system has been investigated using combined methodologies of finite elements and transfer matrices. The balancing was performed through influence coefficient method and the comparison was made by whirl responses between before balancing and after balancing. As a result, balancing of simple spindle model reduced whirl orbit magnitude in case of a completely assembled spindle model.