• Design & Manufacturing
• /
• 제2권4호
• /
• pp.54-61
• /
• 2008

Warpage, which is one of the molding trouble, acts as possible factor which results in defect in assembly. In this study, a mold was designed to produce specimens with rib parallel to flow direction, specimens with rib perpendicular to flow direction and specimens without rib. This work researched change of warpage according to injection molding condition such as injection pressure, packing pressure, packing time, resin temperature, mold temperature in non-crystalline resins(PC, ABS), crystalline resins(PP, PA66), and 30% glass fiber reinforced-resins(PC, ABS, PP, PA66).Specimens with rib and Crystalline resins show more warpage than specimens without rib and non-crystalline resins, respectively. Glass fiber reinforced-resins and specimens with rib parallel to flow direction show smaller warpage than conventional resins and specimens with rib perpendicular to flow, respectively. Specimens with rib and specimens without rib show reduced warpage as packing time increases. In addition, warpage increase as resin temperature increases. It is found that CAE shows similar tendency with experiment as packing time, resin temperature. when the rib is caused, warpage will reduce and prevent the transformation. product of a irregular form occurs warpage. In the study It'll be basic data that product occurs warpage, preferablity.

• Carbon letters
• /
• 제15권4호
• /
• pp.255-261
• /
• 2014

Multi-walled carbon nanotube reinforced epoxy composites were fabricated using shear mixing and sonication. The mechanical, viscoelastic, thermal, and electrical properties of the fabricated specimens were measured and evaluated. From the images and the results of the measurements of tensile strengths, the specimens having 0.6 wt% nanotube content showed better dispersion and higher strength than those of the other specimens. The Young's moduli of the specimens increased as the nanotube filler content was increased in the matrix. As the concentrations of nanotubes filler were increased in the composite specimens, their storage and loss moduli also tended to increase. The specimen having a nanotube filler content of 0.6 wt% showed higher thermal conductivity than that of the other specimens. On the other hand, in the measurement of thermal expansion, specimens having 0.4 and 0.6 wt% filler contents showed a lower value than that of the other specimens. The electrical conductivities also increased with increasing content of nanotube filler. Based on the measured and evaluated properties of the composites, it is believed that the simple and efficient fabrication process used in this study was sufficient to obtain improved properties in the specimens.

• The Journal of Advanced Prosthodontics
• /
• 제11권5호
• /
• pp.297-304
• /
• 2019

PURPOSE. This in vitro study investigated the repair bond strength of the zirconia ceramic after different aging conditions. MATERIALS AND METHODS. In order to imitate the failure modes of veneered zirconia restorations, veneer ceramic, zirconia, and veneer ceramic-zirconia specimens were prepared and were divided into 4 subgroups as: control ($37^{\circ}C$ distilled water for 24 hours ) and 3000, 6000, 12000 thermal cycling groups (n=15). Then, specimens were bonded to composite resin using a porcelain repair kit according to the manufacturer recommendation. The repair bond strength (RBS) test was performed using a universal testing machine (0.5 mm/min). Failure types were analyzed under a stereomicroscope. Two-way ANOVA and Bonferroni test were used for statistical analysis. RESULTS. The RBS values of zirconia specimens were statistically significant and higher than veneer ceramic and veneer ceramic-zirconia specimens in control, 3000 and 6000 thermal cycling groups (P<.05). When 12000 thermal cycles were applied, the highest value was found in zirconia specimens but there was no statistically significant difference between veneer ceramic and veneer ceramic-zirconia specimens (P>.05). Veneer ceramic specimens exhibited cohesive failure types, zirconia specimens exhibited adhesive failure types, and veneer ceramic-zirconia specimens exhibited predominately mixed failure types. CONCLUSION. Thermal cycling can adversely affect RBS of composite resin binded to level of fractured zirconia ceramics.

• Structural Engineering and Mechanics
• /
• 제85권4호
• /
• pp.563-571
• /
• 2023

Girdling underpinning joints are key areas of concern for the pier-cutting bridge-lifting process. In this study, five specimens of an underpinning joint were prepared by varying the cross-sectional shape of the respective column, the process used to treat the beam-column interface (BCI), and the casting process. These specimens were subsequently analyzed through static failure tests. The BCI was found to be the weakest area of the joint, and the specimens containing a BCI underwent punching shear failure. The top of the girdling beam (GB) was subjected to a circumferential tensile force during slippage failure. Compared to the specimens with a smooth BCI, the specimens subjected to chiseling exhibited more pronounced circumferential compression at the BCI, which in turn considerably increased the shear capacity of the BCI and the ductility of the structure. The GB for the specimens containing a column with a circular cross-section exhibited better shear mechanical properties than the GB of other specimens. The BCI in specimens containing a column with a circular cross-section was more ductile during failure than that in specimens containing a column with a square cross-section.

• 구강회복응용과학지
• /
• 제19권2호
• /
• pp.75-86
• /
• 2003

The purpose of this study was to evaluate their mechanical properties after laser-welding or soldering of precious and non-precious dental alloys. For this study, 30 Co-Cr alloy specimens, 15 gold alloy specimens, 15 palladium alloy specimens were casted and seperated on the middle area. 15 sperated Co-Cr specimens and 15 seperated gold alloy specimens were laser welded (GW Group). 15 sperated Co-Cr specimens and 15 sperated gold alloy specimens were soldered by coventional soldering method (GS Group). 15 sperated Co-Cr specimens and 15 seperated palladium alloy specimens were laser welded (PW Group). 15 sperated Co-Cr specimens and 15 sperated palladium alloy specimens were soldered by coventional soldering method (PS Group). Tensile strength, 0.2% yield strength, % elongation were recorded in nine specimens of each group. Bending strength were record in six specimens of each group. These data for four groups were subjected to a two-way analysis of variance(ANOVA). The fracture locations, fractured surfaces were examined by SEM(scanning electron microscope). The results were as following: 1) In the same alloy combination, the tensile strength and 0.2% yield strength and of the laser welded group with same metal combination were significantly less than soldered groups(p<0.05). 2) In the combination of Co-Cr/Palladium, the bending strength of laser welded group were significantly less than that of soldered groups(p<0.05). In the combination of Co-Cr/Gold, the bending strength of laser welded group were significantly higher than that of soldered groups(p<0.05). 3) In the same method of joint, the tensile strength and 0.2% yield strength and bending strength of the Co-Cr/gold were significantly higher than Co-Cr/palladium(p<0.05). 4) There was no significantly statistical difference between each group in the % elongation(p>0.05). 5) The fracture of the laser welded specimens occured in the welding area and a large void was observed at the center of the fracture surface. 6) The fracture of the soldered specimens occured also inthe soldered area and many porpsities were showed at the fracture sites.

• 치위생과학회지
• /
• 제17권4호
• /
• pp.358-367
• /
• 2017

본 연구에서는 소성한 치과도재 시편에 대해 glazing 처리 여부에 따른 수분 침투와 기계적 물성의 비교분석을 통해 glazing 처리의 중요한 의미를 도출하고자 하였다. 또한, 제한된 가속 시효처리 방법으로 구강 내 환경에서 치과용 수복물의 내구수명 예측이 가능하였으며 수분 내에서 가속 시효처리를 통하여 치과도재는 수분 노출로 인한 열화가 일어나고 굽힘강도 저하 현상을 보였다. 치과도재의 glazing 처리를 통해 연마 시 발생하는 시편 표면의 흠집 또는 소성시 발생하는 미세균열이나 기공의 노출을 억제함으로써 굽힘강도 향상 결과를 보였다. 또한 glazing 처리한 시편이 가속 시효처리의 시간이 증가할수록 강도 저하 현상을 보이긴 하지만 glazing 처리를 하지 않은 시편과 비교하여 볼 때, 열화되는 속도가 작은 것을 알 수 있었다. 따라서 구강 내에서 치과도재 보철의 내구성을 확보하기 위해서 영구장착 전 glazing 처리를 반드시 시행할 것을 권하며, 수분 침투 억제 방법에 대해서도 향후 체계적인 연구가 되어야 할 것으로 생각한다.

• Computers and Concrete
• /
• 제22권1호
• /
• pp.93-100
• /
• 2018

It is seldom possible that geotechnical materials like rocks and concretes found without joints, cracks, or discontinuities. Thereby, the impact of micro-cracks on the mechanical properties of them is to be considered. In the present study, the effect of micro-crack on the failure mechanism of rock specimens under uniaxial compression was investigated experimentally. For this purpose, thermal stress was used to induce micro-cracks in the specimens. Several cylindrical and disk shape specimens were drilled from granite collected from Zanjan granite mine, Iran. Some of the prepared specimens were kept in room temperature and the others were heated by a laboratory furnace to different temperature levels (200, 400, 600, 800 and 1000 degree Celsius). During the experimental tests, Acoustic Emission (AE) sensors were used to monitor specimen failure at the different loading sequences. Also, Scanning Electron Microscope (SEM) was used to distinguish the induced micro-crack by heating in the specimens. The fractographic analysis revealed that the thin sections heated to $800^{\circ}C$ and $1000^{\circ}C$ contain some induced micro-fractures, but in the thin sections heated to $200^{\circ}C$, $400^{\circ}C$ and $600^{\circ}C$ have not been observed any micro-fracture. In the next, a comprehensive experimental investigation was made to evaluate mechanical properties of heated and unheated specimens. Results of experimental tests showed that induced micro-cracks significantly influence on the failure mode of specimens. The specimens kept at room temperature failed in the splitting mode, while the failure mode of specimens heated to $800^{\circ}C$ are shearing and the specimens heated to $1000^{\circ}C$ failed in the spalling mode. On the basis of AE monitoring, it is found that with increasing of the micro-crack density, the ratio of the number of shear cracks to the number of tensile cracks increases, under loading sequences.

• Journal of the Korean Wood Science and Technology
• /
• 제14권1호
• /
• pp.55-60
• /
• 1986

Discoloration sensitivities of woods grown in this country haven't reported yet. Therefore we examined discoloration sensitivities of domestic wood specimens to iron (0.1 %, $FeCl_3.6H_2O$), alkali (pH 12.0, NaOH). acid (pH 1.0, $C_2H_2O_4$) and exposing to sunlight (40 hrs), Thirty-six hardwood species were collected and examined. All specimens were prepared from heartwoods of the collected species. But the specimens of 4 Betula species were divided into sapwoods and heartwoods. By iron stain, the color differences (${\Delta}E$) of 21 wood specimens including one Betula sapwood showed above 12.0, which means strong discoloration sensitivities, and of 3 specimens including one Betula sapwood showed below 2.5, which means weak discolorations. The most strong iron discoloration species was Jungkukgulpi-namu (Pterocarya stenoptera). By alkali stain, the color differences (${\Delta}E$) of 3 wood specimens showed above 9.0, which means strong discoloration sensitivities, and of 18 wood specimens including 4 Berula sapwoods showed below 2.5, which means weak discolorations. By acid stain, the color differences (${\Delta}E$) of 6 wood specimens showed above 10.0 which means strong discoloration sensitivities, and of 12 wood specimens including one Betula sapwoods showed below 2.5, which means weak discolorations. By exposing to sunlight, the color differences (${\Delta}E$) of 31 wood specimens including one Betula sapwoods showed below 6.5, which means, strong discoloration sensitivities, and of only one specimens showed below 2.5, which means weak discoloration. The most strong discoloration species by exposing to sunlight was Guirung-namu (Prunus padus). In general, it was shown that hardwoods grown in Korea were most subject to change of color by exposing to sunlight and next were by iron stain. Domestic hardwoods showed some differences in discoloration sensitivities from domestic softwoods previously reported.

• Restorative Dentistry and Endodontics
• /
• 제48권1호
• /
• pp.7.1-7.10
• /
• 2023

Objectives: This study aimed to evaluate the surrounding and underlying shades' effect on the color adjustment potential (CAP) of a single-shade composite used in a thin layer. Materials and Methods: Cylinder specimens (1.0 mm thick) were built with the Vittra APS Unique composite, surrounded (dual specimens) or not (simple specimens) by a control composite (shade A1, A2, or A3). Simple specimens were also built only with the control composites. Each specimen's color was measured against white and black backgrounds or the simple control specimens with a spectrophotometer (CIELAB system). The whiteness index for dentistry (WI_D) and translucency parameters (TP₀₀) were calculated for simple specimens. Differences (ΔE₀₀) in color between the simple/dual specimens and the controls were calculated. The CAP was calculated based on the ratios between data from simple and dual specimens. Results: The Vittra APS Unique composite showed higher WID and TP₀₀ values than the controls. The highest values of ΔE₀₀ were observed among simple specimens. The color measurements of Vittra APS Unique (simple or dual) against the control specimens presented the lowest color differences. Only surrounding the single-shade composite with a shaded composite barely impacted the ΔE₀₀. The highest CAP values were obtained using a shaded composite under simple or dual specimens. Conclusions: The CAP of Vittra APS Unique was strongly affected by the underlying shade, while surrounding this composite with a shaded one barely affected its color adjustment.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1994년도 추계학술대회 논문집
• /
• pp.33-43
• /
• 1994

A series of tensile tests have been performed to investigate the hardening behavior of rolled steel sheets. Tensile tests consist of three stages. At the 1st stage, full size tensile specimens were prestrained in the direction of rolling, then mid-sized tensile specimens were cut from the gauge sections of the full size specimens at angles to the rolling direction. At the 2nd stage, mid-sized specimens were prestrained by predetermined magnitudes of strains and miniature tensile specimens were prepared from each of the mid-sized specimens at every 10 degrees. At the final stage, from tests on miniature tensile specimens the hardening behavior of the prestrained sheets has been investigated. According to the experimental results, orthotropic symmetry is reserved during tensile elongation, and one of the orthotropy axes is continuously rotated to specimen axis. Existing theories seem to fail to explain the rotation of orthotropy axis. A new phenomenological model is proposed to explain the strain induced rotation of orthotropy axes.