• 한국도로학회논문집
• /
• 제15권3호
• /
• pp.65-74
• /
• 2013

PURPOSES: This study is to evaluate the dynamic modulus changes of permeable asphalt mixtures by using non-destructive impact testing method and to compare the dynamic moduli of permeable asphalt mixtures through repeated freezing and thawing conditions. METHODS: For the study, non-destructive impact testing method is used in order to obtain dynamic modulus of asphalt specimen and to confirm the change of dynamic modulus before and after freezing and thawing conditions. RESULTS : This study has shown that the dynamic moduli of asphalt concrete specimens consisting of 10%, 15% and 20% porosity are reduced by 11.851%, 1.9564%, 24.593% after freezing and thawing cycles. CONCLUSIONS : Non-destructive impact testing method is very useful and has repeatability. Specimen with 15% porosity has high durability than others.

• 대한안전경영과학회지
• /
• 제18권4호
• /
• pp.179-183
• /
• 2016

The purposes of this research are to modelize test system of SM TESTING by ARENA, software, input several items of specimen's testing process, resources of system and transfer loop, etc, give a hypothesis and then, obtain results reducing the efficiency of the whole system finally by overload of specific facilities in the testing system through the simulation so as to obtain several materials such as specimen and testing facility, transfer loop, etc. by simple and various forms without any necessity of numerical modelization. It will add facilities of over load and reduce facilities with low operation rate, so increase the efficiency of the system.

• 비파괴검사학회지
• /
• 제28권1호
• /
• pp.64-69
• /
• 2008

압력용기 및 구조물 용접부의 내부결함을 검출하기 위해서는 방사선투과시험과 초음파탐상시험을 시행한다. 그러나 방사선투과시험은 방사선 노출 위험성과 필름 현상처리 소요 등으로 결과의 확인에 상대적으로 긴 시간이 소요되어 제작 공정에 영향을 준다. 일반적인 수동 초음파탐상시험은 결과의 재현이 용이하지 않으며 검사자의 기량에 대한 의존도가 높다는 문제점을 가지고 있다. 이에 대한 대안으로 자동 초음파탐상시험 기법의 하나인 TOFD의 적용이 확산되고 있다. 본 연구는 결함을 포함한 시험편에 대하여 방사선투과 시험과 TOFD 기법을 적용하고 비교한 결과를 기술하였다. TOFD 기법은 초음파 시험기법의 객관적 신뢰도 향상에 기여하게 될 것으로 판단된다.

• 항공우주시스템공학회지
• /
• 제4권2호
• /
• pp.21-25
• /
• 2010

Fatigue properties of composite materials are extremely important to design durable and reliable helicopter rotor blades. However, it is very difficult to apply conventional fatigue test loads in short period. Therefore, accelerating test speed and facilitating spectrum load realization are required. In this study, we have developed a fatigue testing method that uses a resonance of simply supported beam type blade specimen. This test consists in exciting the blade specimen with a frequency that corresponds to its natural frequency. In that case, the test specimen similar to a beam fixed between two pivot points starts vibrating and is significantly deformed. Resonant fatigue tests were performed by changing exciting vertical amplitude and frequency, and S-N curves of each composite materials were successfully obtained.

• 항공우주기술
• /
• 제9권2호
• /
• pp.1-7
• /
• 2010

Fatigue properties of composite materials are extremely important to design durable and reliable helicopter rotor blades. However, it is very difficult to apply conventional fatigue test loads in short period. Therefore, accelerating test speed and facilitating spectrum load realization are required. In this study, we have developed a fatigue testing method that uses a resonance of simply supported beam type blade specimen. This test consists in exciting the blade specimen with a frequency that corresponds to its natural frequency. In that case, the test specimen similar to a beam fixed between two pivot points starts vibrating and is significantly deformed. Resonant fatigue tests were performed by changing exciting vertical amplitude and frequency, and S-N curves of each composite materials were successfully obtained.

• 반도체디스플레이기술학회지
• /
• 제3권2호
• /
• pp.27-33
• /
• 2004

This paper is concerned with development of a micro tensile testing machine for optical functional materials such as single or poly crystal silicon and nickel film. Two micro tensile testers have been developed for various types of materials and dimensions. One of the testers is actuated by a PZT and the other is actuated by a servo motor for a precise displacement control. The specifications of PZT actuated micro tensile tester developed are as follows: the volumetric size of tester is desktop sized of 710$\times$200$\times$270 $mm^3$; the minimum load capacity and the load resolution in the load cell of 1N are 3 mN and 0.1 mN respectively; the full stroke and the stoke resolution of piezoelectric actuator are 1 mm and 10nm respectively. A special automatic specimen installing equipment is applied in order to prevent unexpected deformation and misalignment of specimens during handling of specimen for testing.

• 한국해양공학회지
• /
• 제14권2호
• /
• pp.99-105
• /
• 2000

This paper describes the effect of specimen size on fatigue crack growth rate for the offshore structural high-tensile-strength steel BS4360 and machine structural steel SM45C. The purpose of the present study is to investigate the effect of stress ratio aspect ratio specimen width and specimen thickness of the fatigue crack growth behavior. Compact tension specimens with a LT orientation for BS4360 and SM45C steels were used, All testing was done at constant stress intensity factor range controlled fatigue crack growth condition. The investigation demonstrates that the fatigue crack growth rate is increased with increasing stress ratio and specimen thickness and is decreased with increasing specimen width. The fatigue crack growth rate is unaffected by aspect ratio until a/W=0.50 but is increased by increasing spect ratio from a/W=0.55.

• Journal of Mechanical Science and Technology
• /
• 제18권4호
• /
• pp.640-648
• /
• 2004

This paper describes a new magnetization method for non-destructive testing with magneto-optical sensor (denoted as MO sensor) which have the following characteristic : high observation sensitivity, independence of the crack orientation, and precise imaging of a complex crack geometry such as multiple cracks. When a magnetic field is applied normally to the surface of a specimen which is significantly larger than its defects, approximately the same magnetic charge per unit area occurs on the surface of the specimen. If there is a crack in the specimen, magnetic charge per unit area has the same value at the bottom of the crack. The distribution of the vertical component of the magnetic flux density, B$\_$Z/, is almost uniform over the no-crack area (denoted as B$\_$Z,BASE/), while the magnetic flux density is smaller in the surroundings of the crack(denoted as B$\_$Z,CRACK/) If B$\_$Z, BASE/ is a bit larger than the saturated magnetic flux density of the MO sensor (B$\_$s/) , then small magnetic domains occur over the crack area and a large domain over the non-crack area because B$\_$Z,CRACK/ is smaller than B$\_$s/.

• 터널과지하공간
• /
• 제30권6호
• /
• pp.551-558
• /
• 2020

기존 시험법은 암석시편의 절리면 직접전단시험시 겉보기 면적의 변화를 고려해야 한다고 명시하고 있다. 본 기술보고는 암석코어 시편의 절리면 직접전단시험시 겉보기 면적 계산방법을 제시하였다. 암석코어 시편의 초기 절리면을 타원으로 가정하고, 타원의 중첩면적 감소를 계산하는 수식을 정리하였다. 전단변위와 겉보기 면적을 정규화하면 타원형상에 관계없이 일정한 변화 비율을 가지는 것을 확인하였다. 암석코어 시편 전단시험을 위한 정규화 실험상수를 제안하여 일반화된 계산방법을 제안하였다. 그 방법을 실제 전단시험의 데이터에 적용하여 결과 변화값을 확인하고, 정확도에 대해 간략히 토의하였다.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제18권3호
• /
• pp.240-249
• /
• 2018

Purpose: The purpose of this research is to find which technique, between the PAUT (Phased array ultrasonic test) that has been used widely in practice and RT (Radiographic test) that was used widely in the past, has the higher reliability as a non-destructive testing of welding points in water wall tubes. Methods: To evaluated the reliability of non-destructive testing, eleven test pieces that were fabricated intentionally, which have the most frequently occurred defect types in water wall tubes and then both the PAUT and RT were performed on those eleven test pieces to compare their reliability. Results: The differences of type of defect, length are occurred due to the characteristics of nondestructive testing. The RT could not detect the lack of fusion defect type in specimen #4 and #8 while PAUT could not detect the lateral crack and 1 mm size small porosity in specimen #11. Conclusion: It is concluded that applying both the RT and PAUT result the best reliability rather than applying only one test method, if it is possible, in nondestructive testing of weld water wall tube in thermal power plant boiler case.