• Environmental Engineering Research
• /
• 제19권1호
• /
• pp.107-113
• /
• 2014

Small sized manganese dioxide particles are immobilized onto the surface of sand by the wet impregnation process. The surface morphology of the solid, i.e., immobilized manganese dioxide natural sand (IMNS) is performed by taking scanning electron microscope images and characterized by the X-ray diffraction data. The specific surface area of the solid is obtained, which shows a significant increase in the specific surface area obtained by the immobilization of manganese dioxide. The $pH_{PZC}$ (point of zero charge) is found to be 6.28. Further, the IMNS is assessed in the removal of As(III) and As(V) pollutants from aqueous solutions under the batch and column operations. Batch reactor experiments are conducted for various physicochemical parametric studies, viz. the effect of sorptive pH (pH 2.0-10.0), concentration (1.0-25.0 mg/L), and background electrolyte concentrations (0.0001-0.1 mol/L $NaNO_3$). Further, column experiments are conducted to obtain the efficiency of IMNS under dynamic conditions. The breakthrough data obtained by the column experiments are employed in non-linear fitting to the Thomas equation, so as to estimate the loading capacity of the column for As(III) and As(V).

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권7호
• /
• pp.1063-1071
• /
• 2004

Accurate heat release analysis of cylinder pressure data is important for evaluating performance in the development of diesel engine However, traditional single zone first law heat release model(SZM) has significant limitations due to the simplified assumption of uniform charge and neglecting local temperature inside cylinder during combustion process. In this study. heat release rate based on single zone heat release model has been evaluated by comparison with computational analysis results using Fire code which is based on multi-dimensional model(MDM). To overcome limitations due to simplicity of single zone assumption. especially the influence of specific heat ratio on gross heat release has been esteemed and newly suggested were the equation $\gamma$= $\gamma$(${T/T}_{max}$) which describes the variations of gases thermodynamic properties with mean temperature and maximum mean temperature inside cylinder Single zone heat release model applied with this equation is shown to give very good results over whole range of operating conditions when compared with computational analysis results based on multi-dimensional model.

• 한국물환경학회지
• /
• 제20권4호
• /
• pp.370-375
• /
• 2004

Synthetic organic polyelectrolytes can be used to condition sludges to enhance their dewaterability. When conditioning biological sludges, the charge on the polymer has a significant impact on the effectiveness of the polymer as a conditioner. The objectives of this investigation were to determine the most effective type and dosage of polymer for conditioning digested sludge prior to dewatering, and to investigate the relationship between dewaterability and particle size. 3 types of digested sludge were used under the different digestion processes like anaerobic digestion, aerobic digestion and intermittent aerobic digestion. CST(capillary suction time), TTF(time-to-filter) and SRF(specific resistance to filtration) were tested as a dewaterability index and the number of particle distribution was analyzed using particle size analyzer. The results indicate that cationic polymer appears to be required for effective conditioning of these 3 types digested sludge and the optimal polymer dosage is about 0.6% of SS. CST and TTF are well correlated with mean particle diameter of which the dimension order is 1.7.

• 한국항공우주학회지
• /
• 제34권1호
• /
• pp.95-102
• /
• 2006

펄스형 플라즈마 전기추력기의 설계기술과 제어기법에 있어서는 과거의 기술에 비하여 많은 도약을 하였다. 그리고, 펄스형 플라즈마 전기추력기의 충전된 전기에너지는 추력기 구동시 중요한 비중을 차지함을 알 수 있다. 펄스형 플라즈마 전기추력기는 매 분사시 축전기에 충전된 전기에너지를 방전시켜 분사 시키므로서 추력을 얻는 장치이다. 따라서, 매 분사시 균일한 추력을 얻고자 할 경우에는 동작시점에서 균일한 전기 에너지가 충전되어 있어야 한다. 따라서, 본 논문에서는 매 분사시 균일한 추력을 얻기 위한 기법과 축전기와 추력기 엔진간의 기하학적 연결에 따른 안정성을 연구하였다.

• 한국표면공학회지
• /
• 제51권1호
• /
• pp.47-53
• /
• 2018

Sn-based lithium-ion batteries have low cost and high theoretical specific capacity. However, one of major problem is the capacity fading caused by volume expansion during lithiation/delithiation. In this study, 3-dimensional foam structure of Cu-Sn alloy is prepared by co-electrodeposition including large free space to accommodate the volume expansion of Sn. The Cu-Sn foam structure exhibits highly porous and numerous small grains. The result of EDX mapping and XPS spectrum analysis confirm that Cu-Sn foam consists of $SnO_2$ with a small quantity of CuO. The Cu-Sn foam structure electrode shows high reversible redox peaks in cyclic voltammograms. The galvanostatic cell cycling performances show that Cu-Sn foam electrode has high specific capacity of 687 mAh/g at a current rate of 50 mA/g. Through SEM observation after the charge/discharge processes, the morphology of Cu-Sn foam structure is mostly maintained despite large volume expansion during the repeated lithiation/delithiation reactions.

• Macromolecular Research
• /
• 제10권1호
• /
• pp.40-43
• /
• 2002

Poly(1', 4'-phenylene-1", 4"-(2"-(2""-ethyl-hexyloxy)) phenylene-1",4"-phenylene-2,5-oxadiazolyl) (PPEPPO) was synthesized and its electrochemical characteristics was investigated as electrode material in redox supercapacitor. The cyclic voltammetry (CV) shows there was scarcely a redox reaction and further suggests n-doping is difficult to occur in this system. However, the discharge curve between 3.0 to 0.01 V is continuously decreased like a straight line, similar to the discharge pattern of EDLC. The initial specific discharge capacitance is ~6.4 F/g, while the specific capacitance of 1000th cycle is ~0.1 F/g. The PPEPPO can be used as the electrode of supercapacitor, emissive material, as well as charge-transporting material in polymer LED.ansporting material in polymer LED.

• Journal of Mechanical Science and Technology
• /
• 제15권10호
• /
• pp.1442-1450
• /
• 2001

The EGR system has been widely used to reduce nitrogen oxides (NO$\_$x/) emission, to improve fuel economy and suppress knock by using the characteristics of charge dilution. However, as the EGR rate at a given engine operating condition increases, the combustion instability increases. The combustion instability increases cyclic variations resulting in the deterioration of engine performance and emissions. Therefore, the optimum EGR rate should be carefully determined in order to obtain the better engine performance and emissions. An experimental study has been performed to investigate the effects of EGR on combustion stability, engine performance,70x and the other exhaust emissions from 1.5 liter gasoline engine. Operating conditions are selected from the test result of the high speed and high acceleration region of SFTP mode which generates more NO$\_$x/ and needs higher engine speed compared to FTP-75 (Federal Test Procedure) mode. Engine power, fuel consumption and exhaust emissions are measured with various EGR rate. Combustion stability is analyzed by examining the variation of indicated mean effective pressure (COV$\_$imep/) and the timings of maximum pressure (P$\_$max/) location using pressure sensor. Engine performance is analyzed by investigating engine power and maximum cylinder pressure and brake specific fuel consumption (BSFC)

• Carbon letters
• /
• 제23권
• /
• pp.9-16
• /
• 2017

This paper introduces a nitrogen-doped ordered mesoporous carbon (NOMC) derived from glucosamine with hybrid capacitive behaviors, achieved by successfully combining electrical double-layer capacitance with pseudo-capacitance behaviors. The nitrogen doping content of the fabricated NOMC reached 7.4 at% while its specific surface area ($S_{BET}$) and total pore volume reached $778m^2g^{-1}$ and $1.17cm^3g^{-1}$, respectively. A dual mesoporous structure with small mesopores centered at 3.6 nm and large mesopores centered at 9.9 nm was observed. The specific capacitance of the reported materials reached up to $328Fg^{-1}$, which was 2.1 times higher than that of pristine CMK-3. The capacitance retention rate was found to be higher than 87.9% after 1000 charge/discharge cycles. The supplementary pseudocapacitance as well as the enhanced wettability and conductivity due to the incorporation of nitrogen heteroatoms within the carbon matrixes were found to be responsible for the excellent capacitive performance of the reported NOMC materials.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 가을 학술발표회 논문집
• /
• pp.613-620
• /
• 2002

Sand Compaction Pile(SCP) is a soil improvement method that a sand charge is introduced into the pipe, and the pipe is withdrawn part away while the sand pile is compacted and its diameter is enlarged. The sand used in this method should be of good quality. In Korea, crushed stone and washed sea sand are used frequently in SCP. However, use of these materials is restricted because of environmental problem and deficiency of supply. In the copper smelting process, about 0.7 million tons of copper slag are produced in Korea. The range of particle size distribution of copper slag is from 0.15mm to 5mm, so it can be a substitute for sand, and the relatively high specific gravity compared with the sand, is its characteristic. Copper slag is hyaline and so stable environmentally that in foreign country, such as Japan, Germany etc., it is widely used in harbor, revetment and offshore structure construction works. Therefore, in this study, the several laboratory tests were peformed to evaluate the applicability of copper slag as a substitute for sand of SCP. From the mechanical property test, the characteristics of sand and copper slag were compared and analyzed, and from laboratory model test, the strength of composite ground was compared and analyzed by monitoring the stress and ground settlement of clay, SCP and copper slag compaction pile. Specially, this study focused on the application of copper slag as sand substitute in SCP pilot tests based on laboratory tests results.

• 한국표면공학회지
• /
• 제52권6호
• /
• pp.326-333
• /
• 2019

The microporous carbon derived from PVDC-resin by a simple heat-treatment under an inert atmosphere exhibits a reasonable specific capacitance for a supercapacitor's electrode. However, the capacitance was rapidly decreased at high charge/discharge rate. The micropores present in an electrode surface hinder the entrance of an electrolyte ion onto the entire surface. To induce the meso-sized pores during the carbonization of PVDC-resin, Mg(OH)₂ was utilized as a hard template. The porous carbon made from the mixture of PVD-Cresin and Mg(OH)₂ include mesopores as well as micropores. The induced mesopores does not homogeneously distributed on the entire surface of the synthesized carbon. The PVDC-resin and Mg(OH)₂ are dissolved in the dimethylformamide for the hard template to evolve the pores on the synthesized carbon uniformly. The carbon made from PVDC-resin with solvent and a hard template contains mostly mesopores resulting in the high power performance. The reduced amount of solvent in the precursor derives the carbon with high specific surface area and high power density.