• Korean Journal of Human Ecology
• /
• v.21 no.1
• /
• pp.141-149
• /
• 2012

This study investigates the effects of wear training on blood pressure and blood lipid profiles. For the purpose of this research, 'wear training' refers to the alternating stimulation of temperature while using specific clothing under controlled situations ($18.8{\pm}0.2^{\circ}C$, $38{\pm}3%RH$). The participants alternated between two different garments producing a $1.5^{\circ}C$ difference in the innerest microclimate temperature over a period of 4 weeks. The experiments in this study were conducted in a comfortable environment after sufficient rest. The results were as follows. The systolic blood pressure and mean arterial pressure were lower in the post test than in the pre test (p<.05). The atherogenic index (AI) was also reduced and the LDL-C/HDL-C ratio increased (p<.05) in the post test. These results demonstrated that wear training positively affected improvement in vascular stiffness.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.1 no.1
• /
• pp.16-26
• /
• 2010

In this paper, we present the result of investigations pertaining to the development of the floating type photovoltaic energy generation system. Pultruded FRP has superior mechanical and physical properties compared with those of conventional structural materials. Since the FRP has an excellent corrosion-resistance and high specific strength and stiffness, the FRP material may be highly appreciated for the development of the floating type photovoltaic energy generation system. In the paper, we discussed the development concepts of the floating type photovoltaic energy generation system, briefly. The mechanical properties of the FRP structural member used in the development are investigated through the tensile and compression tests. Test results are used in the finite element analysis and the design of the system. In addition, bolted connections of the members are briefly discussed and the strengths of FRP bolted connections are estimated based on the results of experiments. The experimental results are compared with the finite element analysis results and discussed briefly. The floating type photovoltaic energy generation system is designed, fabricated, and installed successfully in site.

• Wind and Structures
• /
• v.10 no.1
• /
• pp.61-82
• /
• 2007

This paper presents a novel finite element (FE) model for analyzing coupled flutter of long-span bridges using the commercial FE package ANSYS. This model utilizes a specific user-defined element Matrix27 in ANSYS to model the aeroelastic forces acting on the bridge, wherein the stiffness and damping matrices are expressed in terms of the reduced wind velocity and flutter derivatives. Making use of this FE model, damped complex eigenvalue analysis is carried out to determine the complex eigenvalues, of which the real part is the logarithm decay rate and the imaginary part is the damped vibration frequency. The condition for onset of flutter instability becomes that, at a certain wind velocity, the structural system incorporating fictitious Matrix27 elements has a complex eigenvalue with zero or near-zero real part, with the imaginary part of this eigenvalue being the flutter frequency. Case studies are provided to validate the developed procedure as well as to demonstrate the flutter analysis of cable-supported bridges using ANSYS. The proposed method enables the bridge designers and engineering practitioners to analyze flutter instability by using the commercial FE package ANSYS.

• Structural Engineering and Mechanics
• /
• v.74 no.6
• /
• pp.737-745
• /
• 2020

Nowadays, composite plates are widely used as high-strength structures to fabricate a dynamic loading-resistant armours. In this study, the shock load is applied by an explosion of spherical TNT charge at a specified distance from the circular composite plate. The composite plate contains a two-layer ceramic-metal armour and a poly-methyl methacrylate (PMMA) target layer. The dynamic behavior of the composite armour has been investigated by measuring the transferred effective stress and maximum deflection into the target layer. For this purpose, the simulation of the blast loading upon the composite structure was performed by using the load-blast enhanced (LBE) procedure in Ls-Dyna software. The effect of main process parameters such as the thickness of layers, and scaled distance has been examined on the specific stiffness of the structure using response surface method. After validating the results by comparing with the experimental results, the optimal values for these parameters along with the regression equations for transferred effective stress and displacement to the target have been obtained. Finally, the optimal values of input parameters have been specified to achieve minimum transferred stress and displacement, simultaneously with reducing the weight of the structure.

• Journal of Power System Engineering
• /
• v.10 no.2
• /
• pp.117-123
• /
• 2006

Woven fabrics composites are used as primary structural components in many applications because of their superior properties that offer high specific strength and stiffness. However, the complexity of the fabric structure makes understanding of their failure behavior very difficult. Also, laminate woven fabrics CFRP have unique failure mechanisms such as fiber bridging, fiber/matrix crack and so on. In particular, the delamination phenomenon of the composite materials is one of the most frequent failure mechanisms. So, we estimated interlaminar fracture and damage in composites using as ENF specimen by a 3 point bending test. And AE characteristics were examined for crack propagation on plain woven CFRP. We obtained the following conclusions from the results of the evaluation of the 3 point bending fracture test and AE characteristic estimation. AE counts of maximum crack length were obtained as $85.97{\times}10^4\;and\;93{\times}10^3\;for\;a_0/L=0.3$ and 0.6, respectively. Also the maximum amplitudes were over 80dB at both $a_0/L=0.3\;and\;0.6$. $G_{IIc}$ at that's $a_0/L$ ratio were obtained with $1.07kJ/m^2\;and\;3.79kJ/m^2$.

• Steel and Composite Structures
• /
• v.7 no.1
• /
• pp.19-34
• /
• 2007

This paper presents results of a non-linear finite element analysis of axially loaded slender hollow structural section (HSS) columns, strengthened using high modulus carbon-fiber reinforced polymer (CFRP) longitudinal sheets. The model was developed and verified against both experimental and other analytical models. Both geometric and material nonlinearities, which are attributed to the column's initial imperfection and plasticity of steel, respectively, are accounted for. Residual stresses have also been modeled. The axial strength in the experimental study was found to be highly dependent on the column's imperfection. Consequently, no specific correlation was established experimentally between strength gain and amount of CFRP. The model predicted the ultimate loads and failure modes quite reasonably and was used to isolate the effects of CFRP strengthening from the columns' imperfections. It was then used in a parametric study to examine columns of different slenderness ratios, imperfections, number of CFRP layers, and level of residual stresses. The study demonstrated the effectiveness of high modulus CFRP in increasing stiffness and strength of slender columns. While the columns' imperfections affect their actual strengths before and after strengthening,the percentage gain in strength is highly dependent on slenderness ratio and CFRP reinforcement ratio, rather than the value of imperfection.

• Advances in concrete construction
• /
• v.9 no.2
• /
• pp.173-181
• /
• 2020

Fracture properties of concrete depend on the mix proportions of the ingredients, specimen shape and size, type of testing method used for the evaluation of fracture properties. Aggregates play a key role for changes in the fracture behaviour of concrete as they constitute about 60-75 % of the total volume of the concrete. The present study deals with the effect of size and quantity of coarse aggregate on the fracture behaviour of steel fibre reinforced self compacting concrete (SFRSCC). Lower coarse aggregate and higher fine aggregate content in SCC results in the stronger interfacial transition zone and a weaker stiffness of concrete compared to vibrated concrete. As the fracture properties depend on the aggregates quantity and size particularly in SCC, three nominal sizes (20 mm, 16 mm and 12.5 mm) and three coarse to fine aggregate proportions (50-50, 45-55, 40-60) were chosen as parameters. Wedge Split Test (WST), a stable test method was adopted to arrive the requisite properties. Specimens without and with guide notch were investigated. The results are indicative of increase in fracture energy with increase in coarse aggregate size and quantity. The splitting force was maximum for specimens with 12.5 mm size which is associated with a brittle failure in the pre-ultimate stage followed by a ductile failure due to the presence of steel fibres in the post-peak stage.

• Computers and Concrete
• /
• v.25 no.3
• /
• pp.215-224
• /
• 2020

In the present study, according to the important of porosity in low specific weight in comparison of high stiffness of carbon nanotubes reinforced composite, buckling and free vibration analysis of sandwich composite beam in two configurations, of laminates using differential quadrature method (DQM) is studied. Also, the effects of porosity coefficient and three types of porosity distribution on critical buckling load and natural frequency are discussed. It is shown the buckling loads and natural frequencies of laminate 1 are significantly larger than the results of laminate 2. When configuration 2 (the core is made of FRC) and laminate 1 ([0/90/0/45/90]_s) are used, the first natural frequency rises noticeably. It is also demonstrated that the influence of the core height in the case of lower carbon volume fractions is negligible. Even though, when volume fraction of fiber increases, the critical buckling load enhances smoothly. It should be noticed the amount of decline has inverse relationship with the beam aspect ratio. Investigating three porosity patterns, beam with the distribution of porosity Type 2 has the maximum critical buckling load and first natural frequency. Among three elastic foundations (constant, linear and parabolic), buckling load and natural frequency in linear variation has the least amount. For all kind of elastic foundations, when the porosity coefficient increases, critical buckling load and natural frequency decline significantly.

• 한국태양에너지학회:학술대회논문집
• /
• 2012.03a
• /
• pp.410-413
• /
• 2012

A traditional fabrication method is very difficult to make small robots using embedded sensors, actuators and connectors. Fortunately, Shape Deposition Manufacturing can provide an alternative method, and it has many benefits. Firstly, the weight of robot can be lighter, as it can be consisted of composite materials. Secondly, SDM can make simple robot structures because this approach does not need to use connectors and fasteners. Lastly, SDM gives stiffness and flexibility at the specific parts. Therefore, in this paper, we present a design of 3 segment legs organized by SDM, what the SDM approach is, and compare SDM method with 3 segment prototype legs which uses a traditional approach and made by DGIST.

• Journal of the Korea Furniture Society
• /
• v.15 no.2
• /
• pp.53-62
• /
• 2004

This study explored the development of wood furniture made of aged Castanea crenata Sieb. et Zucc, which has been largely planted in the southern area since 1960s and has hardly been used as furniture materials. First, the physical properties of the chestnut wood including specific gravity, stiffness, and shrinkage were compared with Zelkova serrata, Acer palmatum Thunb., Fagus crenata var. multinevis, Quercus, Tagayasan, Prunus serrulata var. spontanea, Juglans sinenis, Pteronrpus santalinus, Diospyros ebenum, and Fraxinus rhynchophylla, which have largely been used in manufacturing furniture. The chestnut wood had appropliate physical properties for wood furniture like other furniture woods. A piece of small table 50 cm in width, 50 cm in length and 60 cm in height by the chestnut tree was created for a current interior space. Since the diameter of the chestnut tree planted since 1960s is below around 30 cm, the top plate of the table had to be put together by an end-joint technique using a small strip. Finally, it is expected that this study will create a greate motivation for furniture designers, furniture studios and furniture companies in Korea to use the woods from the aged chestnut tree in developing furniture in the future.