• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.05a
• /
• pp.197-200
• /
• 2010

In some cases it is important to be able to measure not only the total sound intensity on a panel surface in a vehicle cabin, but also the components of that intensity due to sound radiation and due to absorption from the incident field. For example, these intensity components may be needed for calibration of energy flow models of the cabin noise. A robust method based on surface absorption coefficient measurement is presented in his paper.

• Proceedings of the Acoustical Society of Korea Conference
• /
• autumn
• /
• pp.367-370
• /
• 2001

Various shapes of the noise barrier frame and construction of the sound absorbing panels are studied. It is found that insertion of the sound absorbing panel into barrier frame results in the decrease of the sound absorption coefficient, while the empty frame shows a peak around 250Hz. Using double sound absorbing panels with air gap can increase sound absorption coefficient up to NRC 0.85.

• The Journal of the Acoustical Society of Korea
• /
• v.37 no.5
• /
• pp.323-330
• /
• 2018

This study investigated effects of absorbent gypsum board in the ceiling on low-frequency heavyweight floor impact sound through sound absorption coefficient and floor impact sound measurement. The sound absorption coefficients were measured with sound absorbent gypsum board, glass wool on gypsum board, and a double panel absorbent gypsum board (absorbent gypsum board + glass wool + absorbent gypsum board). Result showed that the absorbent gypsum board had sound absorption coefficient of 0.1 ~ 0.7 from 200 and 630 Hz octave band. The sound absorption coefficient was increased in all frequency range by adding glass wool. Additional absorbent gypsum board increased sound absorption coefficient up to 250 Hz octave band, but decreased over 250 Hz. Heavyweight floor impact sounds were measured in test building for three materials above, gypsum board, and bare slab. Result showed that glass wool on gypsum board and a double panel absorbent gypsum board reduced by 3 dB ~ 4 dB (single number quantity) heavyweight floor impact sound. Comparing with bare slab condition, floor impact sound reduction was mainly found from 125 Hz to 500 Hz octave band, and the maximum reduction was shown in the 250 Hz octave band.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.65-70
• /
• 2004

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.4
• /
• pp.275-281
• /
• 2014

This study has been analyzed the sound performance of the noise barriers with respect to the configuration of the front perforated panel geometries and the filled absorption materials. Noise barriers' acoustic performance should be required to meet 0.7 of NRC value at least. The global absorbing performance of the barriers have been investigated by changing the opening ratio of the front perforated panel and the absorbing characteristics of the absorbing material using two microphone method. Therefore, It it possible to obtain to increase acoustic performance of the specific frequency ranges by designing the perforate rates of the front panel and absorbing characteristics of the absorbing materials inside, as well. This study try to find out the possibilities of applying the absorbing noise barrier to railway usage.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.219-223
• /
• 2003

For the noise reduction measures in a construction field or near the traffic line receiver is often the most economic measure in order to exclude the propagated sound. The dimension of the barrier is decided by the noise and construction design, and the constructive quality of a soundproof panel shall be secured in accordance with KS F4770 to guarantee the safety of sound barriers. In this paper the problems included in the KS F4770-1 that is the regulation for the metallic sound barrier of the absorption type are identified and it is suggested what to be corrected or improved. Through a series of the analyses, conclusions were reached that it is required to improve test methods in KS F4770-1 as well as to break down test loads for building more cost-effective sound barrier.

• The Journal of the Acoustical Society of Korea
• /
• v.42 no.2
• /
• pp.152-160
• /
• 2023

Sound barrier walls are the most basic way to cope with noise problems in urban residential environments. The most important acoustic function of sound insulation board is represented by sound transmission loss and sound absorption coefficient. However, Korea has not yet established a standard for measuring the sound absorption rate of sound insulation boards. In addition, even in the European standard, where the overall acoustic standard of soundproofing boards has already been established, the sound absorption rate is applied only to the standard for measuring the sound absorption rate of general building finishing materials, and a separate measurement method considering the characteristics of soundproof walls and soundproofing boards is not presented. The sound absorption coefficient should be evaluated by summing up the energy absorbed into the material as well as the energy transmitted through the material, but the current European standard has a problem in that the transmitted sound energy is not taken into account. In this paper, we reviewed the sound absorption coefficient measurement standards of sound insulation boards currently being presented, and verified the difference between the results and the new measurement method considering transmission sound for sound insulation boards actually used in Korea.

• The Journal of the Acoustical Society of Korea
• /
• v.28 no.2E
• /
• pp.60-65
• /
• 2009

The present study aims to investigate the effects of sound diffusers and absorbers on the sound clarity in classrooms. In order to do this, computer simulations were carried out to find the effective area of treatment which could enhance the sound clarity in the room. Acoustic measurements were undertaken in a lecture room with several conditions changing the surface of walls and ceilings with diffusers and absorbers. Diffusion and absorption treatments were applied to the side walls, rear wall and the ceiling of the classroom. SPL, RT, D50, RASTI were measured at 9 measurement points with one sound source and MLS was used as the sound source signal. The results show that higher sound clarity was obtained when diffusers were applied to rear walls and ceiling rather than side walls. Also, it was confirmed that absorption increased sound clarity more effectively with smaller amount in comparison with diffusers. It was also concluded that the effects of sound diffusers and absorbers on the sound clarity could be obtained distinctly at the rear area of the classroom.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.9
• /
• pp.730-734
• /
• 2003

For the noise reduction measures in a construction field or near the traffic line receiver is often the most economic measure in order to exclude the propagated sound. The dimension of the barrier is decided by the noise and construction design, and the constructive quality of a soundproof panel shall be secured in accordance with KS F4770 to guarantee the safety of sound barriers. In this paper the problems included in the KS F4770-1 that is the regulation for the metallic sound barrier of the absorption type are identified and it is suggested what to be corrected or improved. Through a series of the analyses, conclusions were reached that it is required to improve test methods in KS F4770-1 as well as to break down test loads for building more cost-effective sound barrier.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.457-460
• /
• 2004

This study examines the sound insulation of the light-weight wall using light-weight concrete and offers the basic datum for enhancing it. The sound insulation of the light-weight wall is determinated by the density, installation method, absorption materials, air layers etc. Among the factors, the solution of outlet that is the major cause of reducing sound insulation should be made. If absorption materials are installed in the cavity walls, it enhances to 15dB in 500Hz.