• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.1
• /
• pp.28-38
• /
• 2009

Numerical simulation is performed for microdroplet deposition on a pre-patterned micro-structure. The liquid-air interface is tracked by a level-set method, which is improved by incorporating a sharp-interface modeling technique for accurately enforcing the matching conditions at the liquid-gas interface and the no-slip condition at the fluid-solid interface. The method is further extended to treat the contact angle condition at an immersed solid surface. The present computation of a patterning process using microdroplet ejection demonstrates that the multiphase characteristics between the liquid-gas-solid phases can be used to improve the patterning accuracy.

• Journal of ILASS-Korea
• /
• v.6 no.2
• /
• pp.29-36
• /
• 2001

Vortices terminating at free surface have been investigated extensively. however. are focused on surface parallel vortices and little has been known about surface normal vortex or columnar vortex. Visualized experimental results utilizing LlF technique are discussed for the purpose of characterization of columnar vortex interacting with a clean and a contaminated free surfaces and a solid body interface in the present investigation. The results reveal that surface tension changes due to surface contamination although bulk viscosity remains constant and eventually the behavior of a columnar vortex interacting with a contaminated free surface and a solid body interface are totally different from the clean free surface case.

• Journal of the Korean Ceramic Society
• /
• v.21 no.3
• /
• pp.271-277
• /
• 1984

To study interface between crystals grown and molten state in the crusible. Pulling and rotating rate of the shaft were varied in LiF crystal growth by Czochralski method. Lower speed of the pulling and rotating rate increased the degree of convexity in solid-liquid interface and higher speed of the pulling and rotating rate decreased it. Optimum condition of LiF crystal growth obtained as pulling rate was 6.5cm/h when it rotated as 46rpm.

• Journal of Welding and Joining
• /
• v.18 no.1
• /
• pp.70-76
• /
• 2000

A rolled steel for structural parts and lead bronze alloy were bonded each other by a new semi-solid diffusion bonding process to investigate the effect of the process parameters, for example bonding temperature and bonding time, on the interface characteristics, and bonding behavior. It can be possible that manufacture of the bonded steel/lead bronze which has a cylindrical shape with inserted the lead bronze alloy into the steel ring by the diffusion bonding process under the semi-solid condition of the lead bronze alloy without any pressure and flux. It has been know that the control of the amount of the liquid phase in semi-solid lead bronze alloy was very important to obtain soundness interface, since the shear strength of the bonded steel/lead bronze at 850℃ for 60 minutes under the condition of about 40% of the liquid phase in the lead bronze alloy shows maximum value, 210 MPa. The shear strength increases with an increase in bonding time and show maximum value, and then decreases.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.241-246
• /
• 2001

Vortices terminating at free surface have been investigated extensively. Most of investigations, however, are focused on surface parallel vortices and little has been known about surface normal vortex or columnar vortex. Visualized experimental results utilizing LIF technique are discussed for the purpose of characterization of columnar vortex interacting with a clean and a contaminated free surfaces and a solid body interface in the present investigation. The results reveal that surface tension changes due to surface contamination although bulk viscosity remains constant and eventually the behavior of a columnar vortex interacting with a contaminated free surface and a solid body interface are totally different from the clean free surface case.

• Journal of the Korean Ceramic Society
• /
• v.36 no.4
• /
• pp.366-371
• /
• 1999

The effect of VC addition on the microstructural evolution of Fe-TiC cermet has been investigated. The microstructures of the Fe-TiC varied with the amount of VC addition. The addition of 1wt% VC enhanced the instability of liquid-solid interface ; the dissolving interface showed round shape instead of facetted one which was ascribed to the increase of lattice mismatch between TiC and solid-solution carbide. in the speci-men with 10wt% VC the new set of solid-solution carbide grains of uniform and small size was formed in-side coarse TiC particles by diffusion induced recrystallizatin (DIR). With increasing the heat-treatment time fine recrystallized grains were dispersed homogeneously in the matrix and resulted in the increase in fracture strength.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.37-44
• /
• 2000

Numerical investigation is made to study the effects of natural convection on the formation of macrosegregation of a Pb-Sn alloy solidification process in a 2-D confined rectangle mold. The governing equations are calculated using previous continuum models with SIMPLE algorithm doring the solidification process. In addition. to track the solid-liquid interface with time variations. the moving boundary condition Is adopted and irregular interface shapes are treated with Boundary-Fitted Coordinate system. As the temperature reduce from the liquidus to the solidus, the liquid concentration of Sn. the lighter constituent, increases. Then the buoyancy-driven flow due to temperature and liquid composition gradients, called thermosolutal convection or double diffusion, occurs in the mushy region and forms the complicated macrosegregation maps. Related to this phnomena, effects on the macrosegregation formation depending on the cooling condition and gravity values are described.

• Korean Journal of Materials Research
• /
• v.9 no.11
• /
• pp.1112-1116
• /
• 1999

Thermoelectric effects on the temperature changes at the solid- and liquid-phase and its interface were studied by using the unidirectional solidification of $\textrm{Bi}_{2}\textrm{Te}_{3}$. Cooling or heating effects measured with current density. polarity and current passing time were quite different. By separating sole Peltier, Thomson and Joule heat theoretically and experimentally, the Peltier coefficient at the solid/liquid interface of $\textrm{Bi}_{2}\textrm{Te}_{3}$ was -1.10$\times\textrm{10}^{-1}$V, and the Thomson coefficients of solid- and liquid-phase were 7.31\times\textrm{10}^{-4}V/K, 5.77\times\textrm{10}^{-5}V/K, respectively. When D.C. passed from solid-phase to liquid-phase during the crystal growth of $\textrm{Bi}_{2}\textrm{Te}_{3}$ the crystal with more directionality was obtained owing to increase of the temperature gradient in liquid by the Peltier cooling. But in reverse current direction, the crystallinity was not changed significantly.

• Journal of the Korean Ceramic Society
• /
• v.25 no.1
• /
• pp.78-82
• /
• 1988

Good quality LiNbO3 single crystals which can be applied to SAW devices, were grown by Czochralski method. It was observed that the gas-bubbles were concentrated in ring shape at the outer part of grown crystals, and this anomaly was illustrated by modeling the mechanism of gas-bubble entrapment according to the melt flow pattern in the crucible. And this mechanism was also encertained by observation of solid-liquid interface shape of grown crystals. The optimal condition for good quality crystals was known that the solid-liquid interface shape was slightly concave.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.279-279
• /
• 2006

We report a fabrication of carbon nanotube (CNT) monolayer thin film using liquid-liquid interface. The multiwalled carbon nanotube (MWCNT), which were synthesized by the alumina template method formed a monolayer at the liquid-liquid interface after sonicating the MWCNT water-oil dispersion. Moreover, with the addition of ethanol, the MWCNT monlayer was also formed at the liquid-liquid interface. The monolayer is transferable onto solid substrates and the transferred film was observed using atomic force microscopy (AFM)