• Journal of the Korean Society for Heat Treatment
• /
• v.7 no.4
• /
• pp.244-252
• /
• 1994

The morphological changes of primary solid particles as a fuction of process time on Al-Si alloys during semi-solid state processing with a shear rate of 200s were studied. In hypereutectic Al-15.5wt%Si alloy, it was observed that primary Si crystals are fragmented in the early stage of stirring and morphologies of primary Si crystals change from faceted to spherical during isothermal shearing for 60 minutes. In quaternary Al-12.5wt%Si-2.9wt%Cu-0.7wt%Mg alloy system, it was observed both primary silicon and ${\alpha}$-alumunum particles. Microstructural evolution of primary Si crystals was similar to that of the hypereutectic Al-Si alloy but equiaxed ${\alpha}$-Al dendrites are broken into nearly spherical at the early stage of shearing and later stage of the isothermal shearing ${\alpha}$- Al particles are slightly coarsoned by Ostwald ripening. Mechanical properties of Al-Si-Cu-Mg alloy were compared to those from other processes (squeeze casting and gravity casting). After T6 heat treatment, comparable values of hardness were obtained while slightly lower compressive strength values were observed in rheocast alloy. The elongation, on the other hand, exhibited significant increasement of 15% over gravity cast alloy.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.5 no.3
• /
• pp.159-169
• /
• 1981

The mixing length theory is extended to close the momentum queations for two-phase turbulent flow at a first-order closure level. It is assumed that the mass fraction of the particles is of the order of unity, that the particle size is so small that the particles are fully suspended is the primary fluid, and that the relaxation time scale of the particles is of the same order as the time scale of the energy containing eddies so that the suspended particles are responsive to the fluctuating turbulent field. The bulk motion of the particles is treated as a secondary fluid with its own coefficient of momentum transport. The proposed closure is uniformly destributed acress the pipe section. Predicted velocity profiles and the friction factors are in good agreement with avaiable experimental data.

• Journal of the Korean Ceramic Society
• /
• v.33 no.3
• /
• pp.332-338
• /
• 1996

This study was investigated on the recycle feasibility of the waste AC(Ammonium Carbonate) solution produ-ced in a commercial AUC(Ammonium Uranyl Carbonate) conversion plant. AUC particles were produced with the AC solution which was prepared with AC solid-agent instead of ammonia and carbon-dioxide gases. As the results particles of monoclinic shapes has been obtained regardless of the pH change if the carbonate concentration is sufficient in the mother liquore. Also a lot of twinned or aggregated particles were formed in case of the increase of pH in the reaction system but not affected in the change of temperature. Consequen-tly the characteristics of the particles which converted for AUC were produced withAC solution to UO2, particles specific surface area shape sintered density and others were similar to that of the particles which were produced with gases only when the pellets are fabricated in the nuclear fuel manufacturing process So the waste AC solution which is produced in the commercial AUC conversion plant is possible to recycle.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.570-573
• /
• 1999

High brightness (Y$_{x}$/Gd$_{1-x}$ )$_2$O$_3$:Eu Phosphor Particles were directly Prepared in the spray Pyrolysis by adding flux materials such as LiCl and HBO$_3$. The (Y$_{x}$/Gd$_{1-x}$ )$_2$O$_3$:Eu particles prepared from solution with flux material had higher PL (photoluminescence) intensities than those prepared from solution without flux. In the spray pyrolysis, the flux acts as promoter of the growth of crystallite and activation of doping material as in the solid state reaction method. Additionally, the flux improved PL intensity of (Y$_{x}$/Gd$_{1-x}$ )$_2$O$_3$:Eu phosphor particles by densifying the internal structure and eliminating the defect existing inside and surface of (Y$_{x}$/Gd$_{1-x}$ )$_2$O$_3$:Eu phosphor particles.r particles.

• 한국연소학회:학술대회논문집
• /
• 2014.11a
• /
• pp.11-12
• /
• 2014

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.1
• /
• pp.9-17
• /
• 2013

A considerable deal of work has been carried out to get an insight into the gas-solid suspension flows and to specify the particle motion and its influence on the gas flow field. In this paper an attempt is made to develop an analytical model to study the effect of nozzle inlet/exit pressure ratio, particle/gas loading and the particle diameter effect on gas-solid suspension flow. The effect of the particle/gas loading on the mass flow, Mach number, thrust coefficient and static pressure variation through the nozzle is analyzed. The results obtained show that the presence of particles seems to reduce the strength of the shock wave. It is also found that smaller the particle diameter is, bigger will be the velocity as bigger particle will have larger slip velocity. The suspension flow of smaller diameter particles has almost same trend as that of single phase flow with ideal gas as working fluid. Depending on the ambient pressure, the thrust coefficient is found to be higher for larger particle/gas loading or back pressure ratio.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1997.04a
• /
• pp.69-73
• /
• 1997

Microwave Plasma assisted CVD (Chemical Vapor Deposition) and DC Plasma CVD were used to prepare thin and thick diamond film, respectively. Diamond coated silicon nitride and fiee standing diamond thick film were eroded by silicon carbide particles. The velocity of the solid particle was about 220m/sec. Phase transformation and the other crack formation were investigated by using Raman spectroscopy and microscopy.

• 한국연소학회:학술대회논문집
• /
• 2003.05a
• /
• pp.119-127
• /
• 2003

In this study we propose an unsteady I-dimensional model of bed combustion with multiple solid phases, which confers a phase on each solid material. This model can be applied to a variety of bed combustion cases of various configurations and ignition methods. It contains fuel combustion, gaseous reaction, heat transfers between each phase, and geometric changes of the solid particles. An iron ore sintering pot is selected for verifying the model validity and simulation results are compared with the limited experimental data set of various coke contents and air supply rates. They predict the experimental results well and show applicabilities to the various system of the fuel bed with various solid materials.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.275-282
• /
• 2008

This paper presents numerical investigation of multi-phase flow in solid rocket motor nozzle and effect of multi-phases on the performance prediction of the Solid Rocket Motor. Aluminized propellants are frequently used in solid rocket motors to increase specific impulse. An Eulerian-Lagrangian description has been used to analyze the motion of the micrometer sized and discrete phase that consist of the larger particulates present in the Solid Rocket Motor. Uniform particles diameters and Rosin-Rammler diameter distribution method has been used for the simulation of different burning of aluminum droplets generating aluminum oxide smokes. Roe-FDS scheme has been used to simulate the effects of the multi-phase flow. The results obtained show the sensitivity of this distribution to the nozzle flow dynamics, primarily at the nozzle inlet and exit. The analysis also provides effect of two phases on performance prediction of Solid Rocket Motor.

• Biomedical Science Letters
• /
• v.25 no.2
• /
• pp.170-176
• /
• 2019

The objective of this study was to evaluate the characteristics of the mixtures of choline alphoscerate (alpha-glycerylphosphorylcholine, alpha-GPC), in the liquid form, and sucrose ester, which formed a solid composite. The choline alphoscerate solid composites were prepared using different ratios of sucrose ester, and different preparation methods, such as air drying and rotary evaporation, were compared for their preparation efficacy. We examined the characteristics of the solid composites by using scanning electron microscopy (SEM), angle of repose, and moisture content. The ideal mixing ratio of choline alphoscerate and sucrose ester was determined as 1:3 and air drying was found to be more suitable for the preparation of solid composites than rotary evaporation. SEM measurements of the degree of dispersion and the size of particles indicated that a high-temperature air method was more suitable. These results demonstrated the successful preparation of choline alphoscerate solid composites that have potential for industrial use.