• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.83.1-83.1
• /
• 2010

Hydrogenated a-SiGe middle cell for triple junction solar cell was investigated with various process parameters. a-SiGe I-layer was deposited at substrate temperature $245^{\circ}C$ and hydrogen content(R) was up to 26.7. Low optical bandgap(1.45eV) of a-SiGe cell was applied for middle cell although a-SiGe single cell efficiency with low Ge content was higher. And this cell was applied to the middle cell of a glass superstrate type a-Si/a-SiGe/uc-Si triple junction solar cell. The triple junction solar cell was resulted in the initial efficiency of about 9%, area $0.25cm^2$, under global AM 1.5 illumination.

• 전기화학회지
• /
• 제13권1호
• /
• pp.10-18
• /
• 2010

Nanostructured metal oxides have been widely used in the research fields of photoelectrochemistry, photochemistry and opto-electronics. Dye-sensitized solar cell is a typical example because it is based on nanostructured $TiO_2$. Since the discovery of dye-sensitized solar cell in 1991, it has been considered as a promising photovoltaic solar cell because of low-cost, colorful and semitransparent characteristics. Unlike p-n junction type solar cell, dye-sensitized solar cell is photoelectrochemical type and is usually composed of the dye-adsorbed nanocrystalline metal oxide, the iodide/tri-iodide redox electrolyte and the Pt and/or carbon counter electrode. Among the studied issues to improve efficiency of dye-sensitized solar cell, nanoengineering technologies of metal oxide particle and film have been reviewed in terms of improving optical property, electron transport and electron life time.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2002년도 추계학술대회 논문집
• /
• pp.69-73
• /
• 2002

A study on photovoltaic system has a lot of problems. Such as repetition experiment in the same condition, development of MPPT(Maximum Power Point Tracking) algorithm, development of islanding detection algorithm and so forth. The reason Is that solar cell output characteristics are varied by insolarion and surface temperature of solar cell. Therefore, the assistance equipment is required which emulates the solar cell characteristics. In this paper, propose the new modeling of solar cell and verify this modeling using MATLAB simulation. And experiment virtual implement of solar cell system using this modeling.

• 한국전기전자재료학회논문지
• /
• 제36권2호
• /
• pp.136-142
• /
• 2023

In the past, the efficiency of solar cells had been increased in order to increase the efficiency of solar modules. However, in recent years, in order to increase output in the solar industry and market, the competitiveness of solar cells based on large-area solar cells and multi-bus bar has been increasing. Multi-busbar solar module is a technology to reduce power loss by increasing the number and width of the front busbar of the solar cell and reducing the current value delivered by the busbar by half through half-cutting. In the case of the existing M2 (156.75×156.75 mm²) solar cell, even with a half-cut, power loss could be sufficiently reduced, but as the area of the solar cell is enlarged to more than M6 (166×166 mm²), the need for more divisions emerged. This affected not only solar cells but also inverters required for module array configuration. Therefore, in this study, the electrical characteristics of a large-area solar cell and after division were extracted using Griddler simulation. The output characteristics of the module were predicted by applying the solar cell parameters after division to PSPice, and a guideline for the large-area solar module design was presented according to the number of divisions of the large-area solar cell.

• 한국산학기술학회논문지
• /
• 제6권5호
• /
• pp.396-400
• /
• 2005

소규모 독립형 태양광발전시스템의 안정적인 설계를 위해서는 태양전지와 배터리 용량이 매우 중요한 요소이다. 태양전지 및 배터리의 용량산정이 잘못되면 시스템의 동작이 불안정해지고 잦은 고장의 원인이 된다. 따라서 본 논문에서는 안정적인 태양광발전시스템의 설계를 위해 부하특성을 고려한 태양전지와 배터리 용량산정 방안을 제시하였다.

• 태양에너지
• /
• 제17권1호
• /
• pp.17-26
• /
• 1997

단결정 실리콘 태양전지는 PESC(Passivated Emitter Solar Cell), PERC(Passivated Emitter and Rear Cell), Point Contact Cell, PERL(Passivated Emitter and Rear Locally-Diffused Cell) 형태로 기술적인 발전을 해왔다. BCSC(Buried Contact Solar Cell)는 낮은 제조 단가로 높은 효율을 얻을 목적으로 개발되었으며 개량된 형태인 DSBC(Double Sided Buried Contact Cell)는 양면으로 빛을 흡수할 수 있는 장점이 있다.

• Current Photovoltaic Research
• /
• 제12권1호
• /
• pp.17-23
• /
• 2024

Photovoltaic (PV) power generation is the world's best and largest renewable energy that generates electricity with infinite sunlight. Solar cell modules are a component of photovoltaic power generation and must have a long-term durability of at least 25 years. The development of processes and equipment that can be recovered through the recycling of metals and valuable metals when the solar module's lifespan is over has been completed to the level of commercialization, but few processes have been developed that require repair due to initial defects. This is mainly due to the economic problems caused by remaking. However, if manufacturing processes such as repairing solar cell modules that have been proven to be early defects are established and the technical review of long-term reliability and durability reaches a certain level, it is considered that it will be a recommended process technology for environmental economics. In this paper, assuming that a defective solar cell module occurs artificially, a manufacturing process for replacement of solar cells was developed, and a technical verification of the manufacturing technology was conducted through long-term durability evaluation in accordance with KS C 8561. Through this, it was determined that remanufacturing technology for solar cell replacement of solar cell modules that occurred in a short period of time after installation was possible, and the research results were announced through a journal to commercialize solar modules using manufacturing technology in the solar market in the future.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2009년도 추계학술대회 초록집
• /
• pp.156-156
• /
• 2009

High efficiency silicon solar cell technology based on planar technology has been improved by various kinds of process by using the wet etching process. In particular, the buried contact solar cell has been successfully studied. In the present work, a simplified process of the buried contact solar cell has been suggested to help one design effectively the high-efficiency solar cell.

• 전기의세계
• /
• 제30권10호
• /
• pp.655-661
• /
• 1981

The concentrating solar module with high concentration ratio(320)has been studied.in this paper. The solar module was composed of the EMVJ solar cell, (Fresnel Lens-DCPC)concentrator and heat sink, and was measured by using the PASTF system. The experimental result and the result analysis for the individual item of the module were as f ollows; (1) The conversion efficiency of the module was 8.3%. (2) The optical efficiency of the concentrator was 46.5% (DCPC; 84.8%, Fresnel Lens; 54.8%). (3) The thermal loss of the solar cell was 4.9%. And methods for the further improvement of the concentrating solar module efficiency have been suggested.

• 한국태양에너지학회 논문집
• /
• 제39권1호
• /
• pp.1-9
• /
• 2019

Light induced degradation is one of the major research challenges of hydrogenated amorphous silicon related thin film silicon solar cells. Amorphous silicon shows creation of metastable defect states, originating from elevated concentration of dangling bonds during light exposure. The metastable defect states work as recombination centers, and mostly affects quality of intrinsic layer in solar cells. In this paper we present results of light induced degradation in thin film silicon solar cells and discussion on physical origin, mechanism and practical solutions of light induced degradation in thin film silicon solar cells. In-situ light-soaking IV measurement techniques are presented. We also present thin film silicon material with silicon nano-quantum dots embedded within amorphous matrix, which shows superior stability during light-soaking. Our results suggest that solar cell using silicon nano-quantum dots in abosrber layer shows superior stability under light soaking, compared to the conventional amorphous silicon solar cell.