• 한국신재생에너지학회:학술대회논문집
• /
• 2005.11a
• /
• pp.673-676
• /
• 2005

To design the effective usage of electric double layer capacitors (EDLCs) used for a storage device of dye sensitized solar cell(DSC) energy, we first investigated the accumulation state of electrical charges and the charge behavior in the EDLCs. Based on the results. the voltage characteristics of EDLCs connected to DSC energy were evaluated. The results showed that the charge accumulation region concentrated on central part of the carbonaceous electrode in EDLCs and the required times for charging and discharging were almost the same.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.482-485
• /
• 1991

This paper discusses a maximum power point tracking controller (MPPTC) by using chopper with an adjustable input to output voltage. The MPPTC is determined by sensing only the actual voltage from solar cell array. It is simple and continuously tracks the solar cell array maximum power point regardless of the load type. Also, the system obtains protection circuit to protect overcharge and disovercharge against the battery.

• Proceedings of the KIPE Conference
• /
• 2012.11a
• /
• pp.5-6
• /
• 2012

In this paper, a simplified maximum power point tracking technique for the solar charger is presented. Main advantages of the proposed charger include low cost and optimized charge time. The maximum power point tracking method is used to deliver the maximum power from PV array to the battery thereby reducing the charge time. Moreover, the proposed technique which tracks the maximum power point by adjusting output current helps reduce the quantity of required number of sensors for the charger. The experimental protype was implemented by using an 80W PV array, a buck converter and a digital signal processor to verify the feasibility of the proposed method.

• Progress in Superconductivity and Cryogenics
• /
• v.7 no.2
• /
• pp.44-46
• /
• 2005

A SMES can be a perfect alternative energy storage device to the chemical batteries which are needed by most of the renewable energy supply systems. The chemical battery storage system is so expensive to maintain and causes another environmental problem because they are not recyclable. But, SMES has semi-permanent lifetime and no environmental problems cause it only need coolants which is non flammable, clean and recyclable gas. In order to verify the feasibility of a SMES for the renewable electrical power supply system, electrical characteristics of a test SMES coil with the photovoltaic power system were analyzed in this paper. Simulation results show that we can charge 40 amps of current in test SMES coil using solar power system. The experimental verification will be performed just after development of the peak power tracking system for the solar system.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.843-845
• /
• 2011

Due to the short lifetime of the battery-based sensor network, study on the environmental energy-harvesting sensor network is being performed widely. In this paper, we analyze the system-level requirements on the sensor node which is needed for the efficient solar-powered wireless sensor network for the target application. In addition, we explain how the HW/SW components of our real solar-powered sensor node can satisfy the requirements mentioned above.

• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.104-107
• /
• 2007

Among the alternative energy sources, the solar energy is recognized as an important energy source and its application is increasing. Especially in future, the hybrid solar energy generation system with battery will be widely used as an independent distributed power generation system. In this paper, a solar power hybrid home generation system using a contact-less power supply (CPS) that can transfer an electric power without any mechanical contact by using magnetic coupling instead of the power transfer by directly supplying the DC power to the home electric system is proposed. The proposed system consists of a ZVS boost converter, a half bridge LLC resonant converter and contact-less transformer.

• KIPS Transactions on Computer and Communication Systems
• /
• v.9 no.4
• /
• pp.77-82
• /
• 2020

Wireless sensor networks (WSNs) suffer from not only a short lifetime due to limited energy but also an energy imbalance between nodes close to the sink and others. In order to fundamentally solve the short lifetime, recent studies utilize the environmental energy such as solar power. Additionally, WSNs using mobile sinks are being studied to address the energy imbalance problem. This paper proposes an improved CTP (Collection Tree Protocol) scheme which uses these two approaches simultaneously. Basically, it is based on a CTP scheme which is a very popular data collection strategy designed for the typical battery-based WSNs with a fixed sink. Therefore, we tailored it for solar-powered WSNs with a mobile sink. Performance verification confirms that our scheme reduces the number of blackout nodes significantly compared to the typical CTP, thus increases the amount of data collected by the sink.

• Journal of the Korean Solar Energy Society
• /
• v.34 no.4
• /
• pp.17-22
• /
• 2014

The design of a fuel cells stack is important to get optimal output power. This study focuses on the evaluation of fuel cell system for unmaned aerial vehicles (UAVs). Low temperature proton exchange membrane (LTPEM) fuel cells are the most promising energy source for the robot applications because of their unique advantages such as high energy density, cold startup, and quick response during operation. In this paper, a 600 W open cathode LTPEM fuel cell was tested to evaluate the performance and to determine optimal operating conditions. The open cathode design reduces the overall size of the system to meet the requirement for robotic application. The cruise power requirement of 600 W was supported entirely by the fuel cell while the additional power requirements during takeoff was extended using a battery. A peak of power of 900 W is possible for 10 mins with a lithium polymer (LiPo) battery. The system was evaluated under various load cycles as well as start-stop cycles. The system response from no load to full load meets the robot platform requirement. The total weigh of the stack was 2 kg, while the overall system, including the fuel processing system and battery, was 4 kg.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.10a
• /
• pp.743-746
• /
• 2013

Most of existing simulator for wireless sensor networks (WSNs) models the battery-based sensor and provides the MAC and routing protocols designed for the battery-based WSNs. Recently, however, as the energy harvesting sensor systems are studied widely, the require of the simulator for them is getting increased; but the related work is insignificant. Unlike the existing simulators, the simulator for the energy-harvesting WSNs requires the new energy model which is integrated with the energy-harvesting model, rechargeable battery model and energy-consuming model. Additionally, it should provide the well-known MAC and routing protocols designed for the energy-harvesting WSNs, and also provide the user-friendly interface for the convenient usage. In this work, we analysis the existing Castalia simulator and revise it for the user-friendly simulator for the solar energy harvesting WSNs.

• Journal of the Korean Solar Energy Society
• /
• v.33 no.4
• /
• pp.23-30
• /
• 2013

This paper presents the determination method of the hybrid energy storage capacity for compensating the output of wind power when disconnecting from the grid. In the wind power output compensation, a lot of charging and discharging time with lithium-ion battery will be deteriorated the life time. And also, this fluctuation will cause some problems of the power quality and power system stability. To solve these kind of problems, many researchers in the world have been studied with BESS(Battery Energy Storage System) in the wind farm. But, BESS has the limitation of its output during very short term period, this means that it is difficult to compensate the very short term output of wind farm. Using the EDLC (Electric Double Layer Capacitor), it is possible to solve the problem. Installing the battery system in the wind farm, it will be possible to decrease the total capacity of BESS consisting of HESS (Hybrid Energy Storage System). This paper shows simulation results when not only BESS is connected to wind farm but also to HESS. To verify the proposed system, results of computer simulation using PSCAD/EMTDC program with actual output data of wind farms of Jeju Island will be presented.