• Bulletin of the Korean Chemical Society
• /
• v.33 no.4
• /
• pp.1225-1230
• /
• 2012

A new unsymmetrical zinc phthalocyanine has been designed and synthesized based on the 'push-pull' and extended ${\pi}$-conjugation concept for the dye-sensitized solar cells. Three tert-butoxy groups, which act as electron releasing ('push'), enhance the solubility of phthalocyanine in common organic solvents and reduce the aggregation. Hydroxy substituted 9,10-anthraquinones act as electron acceptors ('pull') for the study of photoinduced electron transfer processes as well as grafting onto nanocrystalline $TiO_2$. The new unsymmetrical zinc phthalocyanine was fully characterized by FTIR, UV-vis, $^1H$ NMR, cyclic voltammetry and differential pulse voltammetry. The new sensitizer was tested in dye-sensitized solar cells, and gave a better performance.

• Electrical & Electronic Materials
• /
• v.1 no.1
• /
• pp.26-34
• /
• 1988

Sintered CdS/CdTe solar cells have been farbricated by coating a (Cd+Te) slurry on sintered CdS films followed by the sintering at 625.deg.C for one hour with various heating rates. When cadmium and tellurinm powders are used instead of CdTe powder to form CdS/CdTe junction, CdTe is formed in the temperature range of 290.deg.C-400.deg.C. The microstructure of the CdTe films depends strongly on the heating rate of the sintering due to the low melting temperature and the high vapor pressure of the elemental Cd and Te. An optimum heating rate obtain CdTe films with uniform and dense microstructure which, in turn, improves the efficiency of the sintered CdS/CdTe solar cells. All-polycrystalline CdS/CdTe solar cells with an efficiency of 9.57% under 50mW/cm$^{2}$ tungsten light have been farbricated by using a heating rate of 14.deg.C/min.

• ETRI Journal
• /
• v.26 no.6
• /
• pp.647-652
• /
• 2004

A new ionic liquid, 1-vinyl-3-heptylimidazolium iodide (VHpII), was synthesized and applied as a redox electrolyte for dye-sensitized solar cells. The chemical structure of the synthesized VHpII was confirmed using $^1H$ NMR. Thermogravimetric analysis showed that the VHpII was stable for thermal stress of up to $250^{\circ}C$. The energy conversion efficiencies of the VHpII-based dye-sensitized solar cells were investigated in terms of the effect of a lithium iodide addition. A solar cell containing the redox couple of VHpII and iodine showed a conversion efficiency of 2.63% under 1 sun light intensity at AM 1.5. Adding 0.4 M LiI results in a conversion efficiency of 3.63%, which was an improvement of about 40%. The increased conversion efficiency was ascribed to an increase in external quantum efficiency.

• Journal of the Korean Solar Energy Society
• /
• v.32 no.spc3
• /
• pp.262-268
• /
• 2012

In the recent research technical solutions have been studied to integrate renewable energy into unmanned aerial vehicles to use it as the main power source. As the weight of the aerial vehicle body is essential for its performance, we consider to use light-weight solar cell technology. Furthermore fuel cells are also integrated create a highly energy-efficient aerial robot. In this paper, construction concept and software design of the tilt-rotor aerial vehicle GAORI is introduced which uses solar cells and fuel cells as power source. The future work direction and prognosis are discussed.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.89-93
• /
• 2005

A rear contact solar cell has a potential merit of efficiency improvement by a low shading loss in front surface. a simplified module assembly. and a higher packing density. Among the rear contact solar cells. MWT. metallizationl wrap through MWT solar cells that have the bus bars on the back side and the front side metallization is connected to the back through metal filled laser fired holes in the silicon wafer. This approach has the advantages of a much more uniform appearance. The first fabrication of MWT using a multicrystalline silicon modules in our group showed $12.28\%$ on $125mm{\times}125mm$ active area.

• Transactions on Electrical and Electronic Materials
• /
• v.4 no.3
• /
• pp.29-33
• /
• 2003

Tri-crystalline silicon wafers have three different orientations and three-grain boundaries. In this paper, tri-crystalline silicon (tri-Si) wafers have been used for the fabrication of buried contact solar cells. The optical and micro-structural properties of these cells after texturing in KOH solution have been investigated and compared with those of cast mult- crystalline silicon (multi-Si) wafers. We employed a cost effective fabrication process and achieved buried contact solar cell (BCSC) energy conversion efficiencies up to $15\%$ whereas the cast multi-Si wafer has efficiency around $14\%$.

• 한국태양에너지학회:학술대회논문집
• /
• 2012.03a
• /
• pp.394-396
• /
• 2012

Chemical bath deposition (CBD) process conditions for depositing CdS buffer layers was studied for high efficiencies of CIGS thin film solar cells. Growth rate of CdS thin films has an effect on surface morphology and quality of thin films. By the change of growth rate, CdS buffer layers showed a large difference in surface morphology and this difference was closely related with the photovoltaic properties of CIGS solar cells.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.176-180
• /
• 2003

Tri-crystalline silicon (Tri-Si) wafers have three different orientations and three grain boundaries. In this paper, tri-Si wafers have been used for the fabrication of buried contact solar cells. The optical and micro-structural properties of these cells after texturing in KOH solution have been investigated and compared with those of cast multi-crystalline silicon (multi-Si) wafers. We employed a cost effective fabrication process and achieved buried contact solar cell (BCSC) energy conversion efficiencies up to 15% whereas the cast multi-Si wafer has efficiency around 14%.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.1
• /
• pp.65-69
• /
• 2017

This paper presents a Technology-CAD (TCAD) simulation of the characteristics of crystalline Si pillar array solar cells. The junction depth and the surface concentration of the solar cells were optimized to obtain the targeted sheet resistance of the emitter region. The diffusion model was determined by calibrating the emitter doping profile of the microscale silicon pillars. The dimension parameters determining the pillar shape, such as width, height, and spacing were varied within a simulation window from ${\sim}2{\mu}m$ to $5{\mu}m$. The simulation showed that increasing pillar width (or diameter) and spacing resulted in the decrease of current density due to surface area loss, light trapping loss, and high reflectance. Although increasing pillar height might improve the chances of light trapping, the recombination loss due to the increase in the carrier's transfer length canceled out the positive effect to the photo-generation component of the current. The silicon pillars were experimentally formed by photoresist patterning and electroless etching. The laboratory results of a fabricated Si pillar solar cell showed the efficiency and the fill factor to be close to the simulation results.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1204-1207
• /
• 2009

We investigated the device performance of bulk heterojunction solar cells depending on the active layer thickness. For the systematic comparison, the polymer solar cells comprising RR-P3HT:PCBM (1:0.8 (wt%:wt%)) blend films with different thickness were characterized by impedance spectroscopy, and J-V measurement in dark and solar simulated illumination. The device with 120 nm thickness of active layer exhibited maximum power conversion efficiency of 3.5 % under AM 1.5 100mW/$cm^2$ illumination condition.