• Journal of Korea Foresty Energy
• /
• v.25 no.2
• /
• pp.49-54
• /
• 2006

This study was carried out to provide basic data for using domestic structural softwood lumber efficiently and ensuring structural safety of timber structures. The ratios (k-factor) between static and dynamic MOE measured by ultrasonic device for $2{\times}6$ domestic softwood structural lumber are 1.0602 for Korean red pine, 1.0013 for Korean white pine and 1.2320 for Japanese larch. In machine grade using nondestructive method, 76% of Korean red pine was classified into higher than E9 grade, 85% of Korean white pine was sorted into higher than E7 grade and 68% of Japanese larch was classified into higher than E11 grade. Correlation between MOE and MOR by static bending with k-factor from nondestructive method provide a possibility to predict bending strength and allowable stress of domestic softwood structural lumber.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.1
• /
• pp.11-16
• /
• 1996

The purpose of this paper is to present a summary of assignment design values according to domestic softwood structural lumber grading rules. Allowable stresses for visually graded lumber were determined from basic data on small. clear specimens. The data corrected for variability such as natural defects and other factors. The procedure adopted by Japan was used for assigning allowable design values. Strength ratios in relation to each defect were taken from ASTM D 245-81. Korean pine(Pinus koraiensis S. et Z.), Korean red pine(Pinus densiflora S. et Z.), Japanese larch(Larix leptolepis Gordon) and Needle fir(Abies holophylla Max) were applied to this study. The calculated allowable stresses were same in Korean pine and Korean red pine. These values were highest in Japanese larch lowest in Needle fir. So, it is desirable for these species to be classified into different catagories Species Group. However, accurate comparison in design values on lumber grading rules among U.S., Japan and Korea was somewhat difficult. And full scale testing will be necessary for accurate determination of the correction factors to setting up design values.

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.6
• /
• pp.470-479
• /
• 2010

In this study, the visual grading based on the visual characteristics and structural timber bending test were conducted for domestic yellow poplar dimension lumber. Structural performance of domestic yellow poplar dimension lumber was conducted through the evaluation of strength and stiffness. Visual grading rule of yellow poplar dimension lumber did not exist in Korea. Visual grading of yellow poplar dimension lumber was performed according to the NSLB (Northern Softwood Lumber Bureau) standard grading rules including several hardwood dimension lumber. The allowable bending stress was calculated from the results of a visual grading. Compared with NDS (National Design Specification), the yellow poplar dimension lumber showed enough strength for structural uses. In addition, the visual grading was performed according to the KFRI (Korea Forest Research Institute) grading rule to calculated allowable bending stress and to evaluated the feasibility. The yellow poplar was classified into the pine groups by the KFRI criteria regulated by specific gravity. Allowable bending stress based on weibull distribution had became highly than KFRI criteria, as No. 1 (10.0 MPa), No. 2 (7.4 MPa) and No. 3 (4.1 MPa). And the availability of yellow poplar dimension lumber for structural uses had been confirmed. The Modulus of Elasticity (MOE) of domestic yellow poplar dimension lumber had not met the NDS and KFRI criteria. However, for the use of domestic yellow poplar, average values of MOE which obtained through this test were suggested as design value for domestic yellow poplar. Design values were supposed No. 1, 2 (9,000 MPa) and No. 3 (8,000 MPa).

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.6
• /
• pp.498-506
• /
• 2010

To use domestic softwood for structural lumber, appropriate grading system for quality, production and distribution condition of domestic lumber should be prepared. Kim et al. developed an automatic image processing system for grading domestic structural lumber (2009a and b). This study was carried out to investigate optimal image merging conditions for improving performance of image input system which is the key technique of image processing system, developed in the previous paper. To merge digital images of Korean larch lumber, choosing the green channel information of obtained image data showed the most accurate merging performance. As a pre-treatment process, applying Y-derivative Sharr's kernel filter could improve the image merging accuracy, but the effect of camera calibration was imperceptible. The optimal size of template image was verified as 30 pixel widths and 150 pixel heights. When applying the above mentioned conditions, the error length of images was 3.1 mm and the processing time was 9.7 seconds in average.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.1
• /
• pp.20-27
• /
• 2017

The aim of this paper is to present the modulus of elasticity of $E_L$, $E_R$, $E_T$ along three principal axis of softwood dimension lumber by nondestructive method. Ultrasonic measurement was carried out on defect free wood samples taken by the Japanese Larch, SPF (spruce-pine-fir) and Hem-fir $2{\times}4s$. The ultrasound velocities were measured to calculate young's moduli and it was derived elastic constants for each wood samples using the ultrasound velocities and densities of wood. From the test, $E_L$ was much greater than $E_R$ and $E_T$. $E_R/E_T$ ratios were about 1.3. The high density wood had high young's moduli in three principal axis and the difference in young's moduli between species was greater in transverse direction than longitudinal direction. The anisotropy of the lumber was presented through the calculated elastic moduli and compliances matrix in diagonal term were determined by inverting the stiffness matrix.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.1
• /
• pp.1-7
• /
• 2011

Recently, the visual grading rule of Korea Forest Research Institute (KFRI) was revised and it is necessary to investigate the distribution characteristics of visual graded lumber in accordance with the revised rule. Therefore, in this study, the distribution characteristics of bending strength was investigated with revised visual grading rule and changed prior rule, respectively. The size of specimens was $38{\times}140{\times}3,000$ (mm) and the species were $Larix$ $kaempferi$ and $Pinus$ $koraiensis$. The moisture content was under 18% and the specimens were tested in accordance with ASTM D-198. The number of No. 1 and 2 grades, suitable for structural lumber, was increased when the revised visual grading rule was applied. Moreover, the revised rule was more effective to distinguish sharply between No. 1 and 2 grades and below No. 3 grade. Meanwhile, the lower 5% exclusion limit and allowable stresses were generally decreased when revised visual grading rule had been applied. However, the announcement of Korea Forest Service, tested with small clear specimen, was much lower than the allowable stresses of this test, tested with structural lumber. Therefore, the revision of allowable design values should be considered for more exact use and effective structural design.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.5
• /
• pp.444-450
• /
• 2011

The goal of this study is to investigate bending properties of domestic timber. Three representative structural timber from Larix kaempferi, Pinus koraiensis, and Pinus densiflora, in the northeastern South Korea were selected. Visual grading for the timber was conducted based on KFRI notification 2009-01 and the bending strength for the timber was evaluated based on ASTM D 198 bending. The high percentage of grade 1 and 2 for Larix kaempferi shows that the KFRI notification was optimized for this species. The bending strength distributions from Pinus koraiensis and Pinus densiflora were very similar. It could be possible to specify the allowable bending properties of these two Specification using a united species group similar to spruce-pine-fir. Lastly, the bending strength of $120{\times}180mm$ structural members was higher than both existing values in KBC 2009 and design values for timber of imported species described in the NDS. Thus, 120 mm thick domestic softwoods could replace the commercial imported species and the KBC should be modified to provide design values for both timber and dimensional lumber, respectively, like NDS.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.4
• /
• pp.456-462
• /
• 2015

365 pieces of domestic $38{\times}140{\times}3600mm$ Red pine structural lumber were machine graded conforming to a softwood structural lumber standard (KS F 3020). The allowable bending stresses calculated for each grade were compared with the values currently tabulated in the standard. Four calculation methods for lower $5^{th}$ percentile bending stress were non-parametric estimation with 75% confidence level, 2-parameter and 3-parameter Weibull distribution fit, and bending modulus of rupture (MOR)-modulus of elasticity (MOE) regression based method. Only the data set of Grades E8, E9, and E10 were statistically eligible for the $5^{th}$ percentile calculation. The MOR-MOE regression based method only was able to estimate the lower $5^{th}$ percentile values theoretically for the full range of grades. The results showed that all allowable bending stresses calculated were lower than the design values tabulated in the standard. This implies that the current machine grading system has the pitfall of structural safety. Improvement in current machine grading system could be achieved by introducing the bending strength and stiffness combination grade system.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.6
• /
• pp.521-530
• /
• 2011

Nowadays, market demand of structural Glulam is growing and diversifying. The durability of Glulam should be significantly considered when they are intended to apply for out-door use such as timber bridge and pergola. This study was aimed to develop the manufacturing process of preservative treated structural Glulam using domestic softwood species. 10 m long structural Glulam were manufactured from domestic pitch pine logs with CuAz-3 preservative treatment. At each manufacturing process, the production yield was evaluated. Finally, bending tests were performed to verify the structural performance of manufactured Glulam. From the results, it was shown that the preservative treatment process hardly influenced on the production yield. But domestic pitch pine was proved to not be suitable for making the preservative treated Glulam due to the large difference of preservative permeability between sapwood and heartwood.

• Journal of the Korean Wood Science and Technology
• /
• v.52 no.1
• /
• pp.58-69
• /
• 2024

To evaluate the adhesive characteristics of mixed cross-laminated timber (CLT) using domestic softwoods structural lumber proposed by KS F 3020 and yellow poplar, penetration depth of adhesive and thickness of bonding line were analyzed based on the results of boiling water soaking delamination. 3 Types of adhesives and 2 types of major layer were divided into a 5 ply CLT using yellow popular as minor layer. The bonding performance of the mixed CLT as structural members was evaluated based on the KS F 2081. The thickness of bonding line between layers of the mixed CLT was measured with a scanning electron microscope, and the adhesive penetration depth in the layer members was measured with an optical microscope. As a result of boiling water soaking delamination test of mixed CLT, the CLT specimens using PRF and PUR adhesives met the requirements of KS F 2081. It was verified that the penetration path of the adhesive in the layes was mainly through the tracheid cell in the case of Japanese larch and Korean red pine layers, and through the vessel and radial tissue in yellow popular layers. The penetration depth of the adhesive was the highest for the PRF adhesive under the same pressing time conditions, and the thickness of the bonding line was in inverse proportion to the penetration depth in the case of the PUR adhesive.