• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.66 no.1
• /
• pp.27-32
• /
• 2017

This paper presents a Daubechies wavelet-based fault detection method for fault identification in transmission lines. After the Daubechies wavelet coefficients are calculated, the proposed algorithm has been implemented difference equation using C language. We have modeled a 154kV transmission line using the ATPDraw software and have acquired test data. In order to evaluate effects of DC offset, simulations carried out while varying an inception angle of the voltage $0^{\circ}$, $45^{\circ}$, $90^{\circ}$. For performance evaluation, fault distance was varied. As we can see from the off-line simulation, the proposed algorithm shows rapid and accurate fault detection. Also we can see the proposed algorithm is not affected by the fault inception angle change.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.547-548
• /
• 2015

In order to reduce error of the distance relay, we propose an improved fault locating scheme using DC offset removal filter. We were modeled 154 kV transmission system using ATP software in order to demonstrate the usefulness of proposed scheme, and applied to the proposed scheme using collected voltage signal and current signal by line-to-ground fault.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1852-1857
• /
• 2003

This study is concerned about the development of three-dimensional bending machine for heat exchanger. Recently, three-dimensional bending is required for various heat exchanger. The purpose of this study is design of three-dimensional bending machine by analysis of bending process and structural analysis simulation. The analysis is carried out by FEM simulation using DEFORM and CATIA V5 software. The copper-tube is modeled by shell elements and the machine is modeled by placing proper shell and solid finite elements and fictitious mass properties to represent the real one. The final results of analysis are applied to the design of three-dimensional bending machine and the machine is successfully developed.

• Proceedings of the KIEE Conference
• /
• 1999.11d
• /
• pp.1160-1163
• /
• 1999

In this study, we developed FE-tip lithography system that could apply to multi-tip system and did lithography using FE-tip. The software that control FE-tip lithography system, was proposed for acquiring more adaptive data to compensate the effect of fluctuation. We found that the fluctuation effect was reduced. The minimum line width was related to applied voltage and we observed a movement of Z-axis piezo stage to correct the error of this system. When FE current was 5nA, scanning speed was $3{\mu}m/sec$ and applied voltage was 200V, we made a line pattern which had minimum line width of 614 nm. If we reduce applied voltage to several decades and increase scanning speed to $20{\mu}m/sec$, it is possible to set the minimum line width of 100 nm. The proposed system can be easily applied to multi FE-tip lithography system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.341-342
• /
• 2006

This study is concerned about the development of tower type automatic tool changer. The tower type automatic tool changer is developed to reduce stand-by time by shortening tool change time. The developed system can store more number of tools in small space. A structural analysis for the machine is carried out to check the machine design using commercial software, CATIA V5. In the result of structural analysis, the safety of the developed system is confirmed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.455-456
• /
• 2006

Multi-tasking machines are widely used in machine tool industries nowadays. This study focuses on the effect of load on the structure stabilities of laser multi-tasking machine which is comprehensively combined turning center and laser machine. For design of the machine, simulation of structural analysis is carried out varying number of elements. The analysis is carried out by FEM simulation using the commercial software, CATIA V5. This method showed a proper number of elements can be selected to obtain good result by reduced computation time.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.115-118
• /
• 2002

The purpose of this paper is to design a pick-up for the small form factor optical disk drive and to fabricate a micro-compensatory lens for the pick-up using the micro-compression molding process. At design stage, the optical elements including the objective lens and the compensatory lens are miniaturized. The height of pick-up and free working distance are designed as 2mm and 0.2% respectively. To analyze the fabricated micro-compensatory lens, the system was analyzed using the surface profile of the fabricated micro-compensatory lens and CODE V which is commercial software. The RMS wave front aberration of the system using fabricated micro-compensatory lens is 0.01677λ which is lower than Marechal's criterion, 0.07λ.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.213-213
• /
• 2011

DC arc plasmatron is powerful plasma source to apply etching and texturing processing. Even though DC arc plasmatron has many advantages, it is difficult to apply an industry due to the small applied area. To increase an effective processing area, we suggest a DC-RF hybrid plasma system. The DC-RF hybrid plasma system was designed and made. This system consists of a DC arc plasmatron, RF parts, reaction chamber, power feeder, gas control system and vacuum system. To investigate a DC-RF hybrid plasma, we used a Langmuir probe, OES (Optical emission spectroscopy), infrared (IR) light camera. For RF matching, PSIM software was used to simulate a current of an impedance coil. The results of Langmuir probe measurements, we obtain a homogeneous plasma density and electron temperature those are about $1{\times}1010$ #/cm3 and 1~4 eV. The DC-RF hybrid plasma source is applied for plasma etching experimental, and we obtain an etching rate of 10 ${\mu}m$/min. through a 90 mm of reaction chamber diameter.

• Proceedings of the KAIS Fall Conference
• /
• 2011.05a
• /
• pp.73-76
• /
• 2011

최근 배전계통에 태양광전원의 전력변환장치나 비선형기기에서 발생되는 고조파는 보호계전기의 오동작 및 기기의 손실 등을 초래하여, 이에 대한 전력품질특성 해석이 필수적인 상황이다. 따라서 본 논문에서는 태양광전원이 연계되어 정상운용중인 배전계통에 미치는 전력품질 특성시험을 위하여, LabVIEW를 이용한 전력품질 평가시스템을 제작하였다. 그리고 이 장치를 통해 태양광전원 연계 시 발생하는 고조파특성을 분석하여, 제한한 평가시스템의 유용성을 확인하였다.

• Proceedings of the Korean Information Science Society Conference
• /
• 2005.11b
• /
• pp.475-477
• /
• 2005

향후 유비쿼터스 컴퓨팅 환경에서의 임베디드 소프트웨어는 다원화된 네트워크 환경에서 동작하게 될 것이다. 임베디드 소프트웨어가 이 기종의 시스템에서 다양한 형태의 응용 프로그램으로 쉽게 탑재되기 위해서는 설계와 코드의 재사용이 필수적이다. 임베디드 시스템에서 소프트웨어 설계의 재사용이 가능하다면 개발 시 소요되는 시간과 비용이 절감될 것이다. 그러나 임베디드 소프트웨어는 많은 부분이 시스템에 의존적이기 때문에 재사용이 어렵다는 단점을 가지고 있다. 본 논문에서는 이러한 단정을 해결하고자 기존의 MDA 메커니즘과 개선한 Multiple V-model의 접목을 시도하고 임베디드 소프트웨어 컴포넌트 설계의 재사용을 제안하다. 그리고 적용사례로서, 이기종의 임베디드 시스템들에 소프트웨어 컴포넌트를 탑재하였다.