• 전기학회논문지P
• /
• 제65권2호
• /
• pp.122-129
• /
• 2016

Current differential protection relaying with second harmonic restraint is the main protection for large capacity power transformer. PSCAD simulation program is widely used for modeling of dynamic varying transients phenomena. This paper deals with a power transformer model and transients analysis using PSCAD software to develop IED for power transformer. Simulation was carried out using a three phase 40MVA, 154/22.9kV, 60Hz, two-winding transformer with Y-Y connection used in actual fields. The paper analyzed transformer magnetizing inrush, external fault, and internal fault conditions with this model in the time domain. In addition, we performed an analysis in the frequency domain using FFT during several conditions.

• 전기학회논문지P
• /
• 제65권2호
• /
• pp.142-150
• /
• 2016

This paper developed new manufacture process technology of slim type flexible flat lighting product used lower power white LED. Flexible flat lighting is applied to letter sign lighting, traffic lighting, interior wall lighting, flat lighting, aquarium back lighting, wreath light etc. Main manufacture process technology were developed drawing software for electronics circuit, inkjet electronic circuit pattern and inkjet white ink coating. For pattern printing it was utilized for piezoelectonic inkjet head printing technology. Also high vacuum pressure laminating technology was waterproofing for LED flat lighting protection. Hence, form process technology we were manufactured for flexible flat lighting product of the power 12 W, input voltage 48 V and plane size $480{\times}480mm$. It acquired a these validity from experiment results.

• 전기학회논문지P
• /
• 제66권1호
• /
• pp.27-32
• /
• 2017

This paper presents a Daubechies wavelet-based fault detection method for fault identification in transmission lines. After the Daubechies wavelet coefficients are calculated, the proposed algorithm has been implemented difference equation using C language. We have modeled a 154kV transmission line using the ATPDraw software and have acquired test data. In order to evaluate effects of DC offset, simulations carried out while varying an inception angle of the voltage $0^{\circ}$, $45^{\circ}$, $90^{\circ}$. For performance evaluation, fault distance was varied. As we can see from the off-line simulation, the proposed algorithm shows rapid and accurate fault detection. Also we can see the proposed algorithm is not affected by the fault inception angle change.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2015년도 제46회 하계학술대회
• /
• pp.547-548
• /
• 2015

In order to reduce error of the distance relay, we propose an improved fault locating scheme using DC offset removal filter. We were modeled 154 kV transmission system using ATP software in order to demonstrate the usefulness of proposed scheme, and applied to the proposed scheme using collected voltage signal and current signal by line-to-ground fault.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1852-1857
• /
• 2003

This study is concerned about the development of three-dimensional bending machine for heat exchanger. Recently, three-dimensional bending is required for various heat exchanger. The purpose of this study is design of three-dimensional bending machine by analysis of bending process and structural analysis simulation. The analysis is carried out by FEM simulation using DEFORM and CATIA V5 software. The copper-tube is modeled by shell elements and the machine is modeled by placing proper shell and solid finite elements and fictitious mass properties to represent the real one. The final results of analysis are applied to the design of three-dimensional bending machine and the machine is successfully developed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 C
• /
• pp.1160-1163
• /
• 1999

In this study, we developed FE-tip lithography system that could apply to multi-tip system and did lithography using FE-tip. The software that control FE-tip lithography system, was proposed for acquiring more adaptive data to compensate the effect of fluctuation. We found that the fluctuation effect was reduced. The minimum line width was related to applied voltage and we observed a movement of Z-axis piezo stage to correct the error of this system. When FE current was 5nA, scanning speed was $3{\mu}m/sec$ and applied voltage was 200V, we made a line pattern which had minimum line width of 614 nm. If we reduce applied voltage to several decades and increase scanning speed to $20{\mu}m/sec$, it is possible to set the minimum line width of 100 nm. The proposed system can be easily applied to multi FE-tip lithography system.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.341-342
• /
• 2006

This study is concerned about the development of tower type automatic tool changer. The tower type automatic tool changer is developed to reduce stand-by time by shortening tool change time. The developed system can store more number of tools in small space. A structural analysis for the machine is carried out to check the machine design using commercial software, CATIA V5. In the result of structural analysis, the safety of the developed system is confirmed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.455-456
• /
• 2006

Multi-tasking machines are widely used in machine tool industries nowadays. This study focuses on the effect of load on the structure stabilities of laser multi-tasking machine which is comprehensively combined turning center and laser machine. For design of the machine, simulation of structural analysis is carried out varying number of elements. The analysis is carried out by FEM simulation using the commercial software, CATIA V5. This method showed a proper number of elements can be selected to obtain good result by reduced computation time.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.115-118
• /
• 2002

The purpose of this paper is to design a pick-up for the small form factor optical disk drive and to fabricate a micro-compensatory lens for the pick-up using the micro-compression molding process. At design stage, the optical elements including the objective lens and the compensatory lens are miniaturized. The height of pick-up and free working distance are designed as 2mm and 0.2% respectively. To analyze the fabricated micro-compensatory lens, the system was analyzed using the surface profile of the fabricated micro-compensatory lens and CODE V which is commercial software. The RMS wave front aberration of the system using fabricated micro-compensatory lens is 0.01677λ which is lower than Marechal's criterion, 0.07λ.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.213-213
• /
• 2011

DC arc plasmatron is powerful plasma source to apply etching and texturing processing. Even though DC arc plasmatron has many advantages, it is difficult to apply an industry due to the small applied area. To increase an effective processing area, we suggest a DC-RF hybrid plasma system. The DC-RF hybrid plasma system was designed and made. This system consists of a DC arc plasmatron, RF parts, reaction chamber, power feeder, gas control system and vacuum system. To investigate a DC-RF hybrid plasma, we used a Langmuir probe, OES (Optical emission spectroscopy), infrared (IR) light camera. For RF matching, PSIM software was used to simulate a current of an impedance coil. The results of Langmuir probe measurements, we obtain a homogeneous plasma density and electron temperature those are about $1{\times}1010$ #/cm3 and 1~4 eV. The DC-RF hybrid plasma source is applied for plasma etching experimental, and we obtain an etching rate of 10 ${\mu}m$/min. through a 90 mm of reaction chamber diameter.