• 마이크로전자및패키징학회지
• /
• 제25권2호
• /
• pp.25-30
• /
• 2018

Sn-Pb솔더는 그동안 자동차 전장품에서 많이 사용되어 왔다. 그러나 최근에 환경과 인체에 대한 유해성 때문에 end-of-life vehicle (ELV)과 같은 국제 환경 규제로 인하여 Pb의 사용이 금지되었다. 이러한 이유로 자동차 전장품을 위한 Pb-free 솔더링에 관한 많은 연구들이 보고 되어 왔다. 한편, 자동차의 연료 효율성과 공간 활용을 위하여 유연성과 경량의 특성을 가지는 플렉시블 기판이 자동차 전장품에 사용되고 있다. 자동차 전장품에 대한 Pb-free 솔더 접합부 특성에 관한 연구들이 많이 진행되었음에도 불구하고 자동차의 사용 환경을 고려한 플렉시블 기판 솔더 접합부에 대한 신뢰성 특성에 관한 연구는 아직 부족한 실정이다. 본 연구에서는 organic solderability preservative (OSP) 및 electroless nickel immersion gold (ENIG) 표면처리 된 플렉시블 기판 위 Sn3.0Ag0.5Cu, Sn0.7Cu, Sn0.5Cu0.01Al(Si) 세 가지 Pb-free 솔더 접합부에 대한 특성을 보고 하였다. 솔더 조성과 기판 표면처리에 따른 접합부의 특성 및 신뢰성을 비교 평가 하기 위하여 인장 강도 시험, 열 충격 시험과 반복 굽힘 시험을 진행 하고 그 결과를 분석하였다. OSP 표면처리 된 기판 접합부에 대한 반복 굽힘 시험 결과 세 종류의 솔더 접합부 모두 파괴는 솔더 내부에서 일어 났으며 Sn3.0Ag0.5Cu 솔더의 접합부에서 반복 굽힘 수명이 가장 길게 나타났다.

• Journal of Welding and Joining
• /
• 제23권5호
• /
• pp.49-54
• /
• 2005

The effective charge number and the critical current density of electromigration in eutetic SnPb and Pb Free $(SnAg_{3.8}Cu_{0.7)$ flip chip solder bumps are studied. The effective charge number of electromigration in eutectic SnPb solder is obtained as 34 and the critical current density is $j=0.169{\times}({\delta}_{\sigma}/{\delta}_x})\;A/cm^2,\;where\;({\delta}_{\sigma}/{\delta}_x})$ is the electromigration-induced compressive stress gradient along the length of the line. While the effect of electromigration in Pb free solder is much smaller than that in eutectic SnPb, the product of diffusivity and effective charge number $DZ^{\ast}$ has been assumed as $6.62{\times}10^{-11}$. The critical length for electromigration are also discussed.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2002년도 추계학술발표강연 및 논문개요집
• /
• pp.65-65
• /
• 2002

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2002년도 춘계 기술심포지움 논문집
• /
• pp.126-129
• /
• 2002

This article presents that the affecting factors to solderability and initial reliability. It was discussed that effect of the solder ball hardness and composition on the reliability of solder joints. In this study, lead free solder alloys with compositions of Sn-Cu, Sn-Ag, Sn-Ag-Cu, Sn-Ag-Cu-Bi were applied to the $\muBGA$ packages. As a result of experiments, the high degree of hardness with the displacement of 0.22mm was obtained Sn-2.0Ag-0.7Cu-3.0Bi. The shear strength of lead free solder was higher than of Sn-37Pb solder, and it was increased about 150% in Sn-2.0Ag-0.7Cu-3.0Bi.

• 마이크로전자및패키징학회지
• /
• 제9권4호
• /
• pp.1-9
• /
• 2002

Ball grid array (BGA) substrate 상의 0.5 $\mu\textrm{m}$Au/5 $\mu\textrm{m}$Ni/Cu 층으로 구성된 접촉 패드(pad)와 In-15(wt.%)Pb-5Ag 솔더 볼 사이에서 리플로우 및 고상 시효동안 일어나는 금속학적 반응 특성이 조사되었다. 1-5 분의 리플로우 시간에 따라 솔더/패드 계면에서 $AuIn_2$ 또는 Ni-In 금속간 화합물층이 형성됨이 관찰되었다. 리플로우 동안 용융 In-l5Pb-5Ag 솔더 내로의 Au 층의 용해 속도는 $2\times 10^{-3}$ $\mu\textrm{m}$/sec 정도로 측정되어 공정 Sn-37Pb와 비교하여 매우 느린 것으로 관찰되었다. $130^{\circ}C$에서 500시간의 고상 시효 후에는 초기 리플로우 시간에 관계없이 $Ni_{28}In_{72}$ 금속간 화합물층이 약 3 $\mu\textrm{m}$까지 성장하였다. 이를 통하여 솔더 합금에서의 In 원자들은 아래의 Ni 층과 반응하기 위하여 리플로우 동안 형성된 $AuIn_2$상을 통하여 확산하는 것으로 관찰되었다. 미세구조 관찰과 전단 시험을 통하여 In-l5Pb-5Ag합금의 경우는 Sn-37Pb 조성과는 달리 Au/Ni surface finish 상에 사용시에도 솔더 접합부에서의 Au-embrittlement를 야기 시키지 않는 것으로 분석되었다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.481-486
• /
• 2002

We have investigated the effects of plating materials for Cu lead (Sn-lOPb, AwPdJNi, Sn-3.5Ag, Sn-3Bi and Sn-0.7Cu) on properties of QFP joints using a Sn-8Zn-3Bi solder. The results were compared with the joints using Sn-3. 5Ag-0. 7Cu and Sn-37Pb solders. As a result, the joints with the Sn-3.5Ag, Sn-3Bi and Sn-0.7Cu plated Cu lead had the reliability comparable to those of the Sn-3.5Ag-0.7Cu and Sn-37Pb soldered joints with respect to the joint strength after the high temperature holding tests at 348K to 423k. In particular, the joint with the Sn-3.5Ag plated Cu lead had the best reliability. This is caused by the low growth rate of a Cu-Sn interfacial reaction layer that degrades the joint strength of the soldered joints. Consequently, the Sn-3.5Ag plating was found to be most feasible plating for the Sn-8Zn-3Bi soldered joint.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2003년도 기술심포지움 논문집
• /
• pp.63-67
• /
• 2003

Electromigration characteristics of $SnAg_3Cu_{0.7}$ and eutectic SnPb solder were studied using thin stripe-type test structures. Significant changes in the microstructure of two solders were observed after electromigration test, in which the temperature and the current density were varied from 90 to $110^{\circ}C$ and from $4.0\times10^4\;A/cm^2\;to\;9.2\times10^4\;A/cm^2$. In SnAgCu solders, hillocks were main]y observed near the anode end. From resistance measurements, it was calculated that the activation energy of the SnAgCu solder for electromigration was 1.04 eV And in eutectic SnPb without the effect of pads, while depleted region was found near cathode end, Sn-rich hillocks were observed near the anode end. During eutectic SnPb electromigration, it were observed that electromigration behavior had two migration modes.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2003년도 추계학술발표대회 개요집
• /
• pp.86-88
• /
• 2003

The characteristic of induction heating solder bump(solder ball: Sn-37Pb, Sn-3.5Ag, Sn-3.0Ag-0.5Cu) has analyzed in this paper. The initial condition of induction heating depends on the time and current. The shape of lead-free solder bump is better than lead solder. The shear strength of lead solder bump has decreased with aging time. The average of shear strength of solder bump is about 10N, 11N, and 11N respectively. The lead-free solder bump's shear strength is better than lead solder and varies irregularly with aging time.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1995년도 특별강연 및 추계학술발표 개요집
• /
• pp.110-112
• /
• 1995

Initial solder joint strengths of various solder pastes, such as Sn-Pb(63-37wt%), Sn-In(52-48wt%), Sn-In-Ag(77.5-20-2.5wt%), and Sn-Ag(96.5-3.5wt%) has been studied. A system that can control the solder joint interface temperature during bonding process was also desined and implemented to improve solder joint integrity.

• 한국자동차공학회논문집
• /
• 제22권3호
• /
• pp.90-96
• /
• 2014

The conventional SnPb solders were widely used for several decades in the electronic packing system due to the superior mechanical properties such as low melting point, better wettavility and good mechanical fatigue. However, in recent years, owing to adverse effect on the human health and environment, conventional SnPb solders have been replaced by Lead-free solders. In this research, the shear punch(SP) test of Sn-4Ag-(Cu)/Ni pad was performed. Pb-free solder alloys which are the environmentally friendly of the electronic components were performed at $150^{\circ}C$ for 100hr~1000hr to artificial aging processing. In order to evaluate the mechanical properties of solder joints, the SP test was conducted at $30^{\circ}C$ and $50^{\circ}C$. As a result, the maximum shear strength of almost the whole specimens was decreased with the increase in aging time and temperature of SP test. The mechanical properties of Sn-4Ag-0.5Cu solder were most excellent in all Pb-free solder which were produced by the SP test at $30^{\circ}C$.