• 산업기술연구
• /
• 제22권B호
• /
• pp.155-161
• /
• 2002

As the wireless communications are gradually developed, the higher frequency is demanded and the smaller the size of antenna shall be reduced by the wavelength of the operating frequency. However, the smaller the size of antenna becomes, the less the gain is obtained according to the frequency, so that a new attempt such as an array antenna has been examined to improve the characteristics. Also, for the convenience of communication, the omni-directional property is required. In this paper, two antennas system which is aligned in cross direction in tested and analyzed. The main scope is focused to get an appropriated distance between the two small antennas to get better properties. There are various ways of array arrangement, but in this study, it should be placed on the same PCB for easy implementation and the direction of each antenna are aligned to be a cross($90^{\circ}$) position. The study is carried out by comparing the radiation patterns mainly, and the theoretical expectation and the computer simulation are also executed. The final model is the folded IF-antennas system printed on PCB and the ideal dipole-antenna arrangement in also test to verify the possibility of our implementation. And it is finally proved by measuring experiments.

• 수산해양기술연구
• /
• 제32권4호
• /
• pp.421-431
• /
• 1996

From comparing the impact dynamic absorber with the impact damper in the auxiliary vibration system with the conventional dynamic absorber, the following conclusions are obtained as follows ; 1. Recognizing that the amplitude restraining effect of the impact dynamic absorber become resonable in a comparison of conventional one development of an improved dynamic absorber may be probable. 2. With increasing the frequency ratio, the 1st resonance peak is higher but the 2nd one gets lower. In addition, the frequency ratio is peak located at the same resonance. 3. The optimum impact clearance is smaller and the vibration constraining effect becomes better with and increase in the mass of impact ball. And it is recognizable that the optimum tuning frequency ratio and impact clearance in an accordance with the mass ratio are varied. 4. The optimum tuning condition becomes gradually lower than the case of r=1 and maximum amplitude becomes lower with an increment in the mass ratio. However, the impulse clearance is larger and the working range of restraining vibration amplitude become smaller with a decrement in the mass of impact ball.

• 한국정보통신학회논문지
• /
• 제13권7호
• /
• pp.1272-1278
• /
• 2009

본 논문은 필터의 구현 방식 중 UIR방식과 SIR방식을 비교 제작하여 두 가지 방법 모두 유용하다는 것을 나타내는 것에 그 목적이 있다. UIR방식은 구조가 간단하여 원하는 특성을 얻을 수 있다는 점에서 많이 쓰여 왔다. 그러나 업체들의 요구 기준을 예전과 비교해 볼 때, 가격은 좀 더 싸게, 크기는 좀 더 작게, 성능은 더 좋은 특성이 나오기를 기대한다. 이러한 점에서 SIR방식은 UIR방식보다 좀 더 작은 크기지만 비슷한 특성을 나타내므로 경쟁력에서 좀더 우위를 차지할 수 있으리라고 예상된다. 본 논문에서는 이러한 조건을 바탕으로 SIR방식과 UIR방식을 설계 및 제작하여 비교하였다. 제작 기준으로는 삽입 손실이 0.8dB 이하이고, 반사 손실은 20.0dB 이상이며, 평탄도는 0.3dB 이내로 하였다. 또한 중심 주파수는 현재 CDMA(SKT)에서 사용되고 있는 TX Band인 881.5MHz 대역으로 정하였고, 대역폭을 25.0MHz의 동일한 조건에서 비교하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.748-752
• /
• 2004

Fluid dynamic bearings (FDBs) have been replacing ball bearings of the HDD spindle motor very rapidly. But there are several demerits of HDB, such as high friction torque, variable viscosity of the fluid lubricant depending on operating temperature, low stiffness, and etc. Eccentricity is one of the major parameters which affects the static and dynamic characteristics. As the static eccentricity is larger, the stiffness and the damping coefficients become bigger. But friction torque is relatively unaffected by the static eccentricity. This research proposes a new type of journal bearing with asymmetric journal grooves which results in better dynamic characteristics. The static and dynamic characteristics of the new journal bearing are investigated by solving the Reynolds' equation with FEM, and the transient analysis is performed to predict the dynamic behavior of rotor by solving the equations of motion of a HDD spindle system with Runge-Kutta method. The result shows that the proposed Journal bearings have much bigger stiffness and damping coefficients compared with the conventional symmetric ones. And consequently, it has smaller whirl radius and tilting angle.

• 전자공학회논문지A
• /
• 제31A권5호
• /
• pp.85-93
• /
• 1994

We have studied the effect of channel and/or spacing chirpings on the near field and near field intensity patterns, modal gains and radiation angles of 6 supermodes in the index-guided laser arrays with 6 channels, on the basis of the coupled mode theory. The spacings between channels can be indenpendent parameters for control of the radiation angle. It is found that an asymmetrically v channel-chirped array has both a smaller radiation angle and better supermode discrimination characteristics than a uniform array. Comparing two approaches for enhancing modal stability in point of supermode discrimination characteristics, approach I which increases the coupling cofficient between the outer-most waveguides at each end of an otherwise uniform array, has superior discrimination characteristics to the approach II which increases the propagation constant for the end elements with the same coupling between neighbor elements. Approach III which has a narrower spacing between the outer-most waveguides at one end and a wider channel width of the outer-most waveguide at another end, gets a narrower radiation angle than the approach I and good supermode discrimination characteristics by applying optimized gain profiles.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회
• /
• pp.241-252
• /
• 2010

This study investigates the application of dilatometer test for evaluating the deformation characteristics of granular soil. $K_D$ is the most sensitive to the stress history among CPT and DMT measurements, and $E_D$ and $q_c$ are observed to be similarly affected by the stress history. The coefficient of at-rest earth pressure($K_0$) is an indirect measure evaluating the stress history of granular soil. A relation using only DMT indices provides appropriate prediction of $K_0$ values. Although penetration of dilatometer inevitably induces the failure of cementation bonds, $E_D$ reflects the deformation characteristics of undamaged cementation relatively well. Therefore, a slightly better prediction of M value for cemented sand is achieved by using $E_D$ rather than $q_c$. Because of the weaker particle strength of calcareous sand compared than quartz sand, the majority of sand particles adjacent to dilatometer probe will be crushed during penetration. The particle crushing will induce the less contraction of the dilatometer membrane during penetration, consequently, the smaller $K_D$ and $E_D$ of calcareous sand.

• 한국분무공학회지
• /
• 제17권2호
• /
• pp.64-70
• /
• 2012

Water mist fire suppression systems which use relatively small droplets of water with high injection pressure are increasingly being used in wider applications because of its greater efficiency, low flooding damage and low toxicity. However, the performance of the system significantly relies on the water mist characteristics and it requires better understanding of fire suppression mechanism of water mist. In the present study, computational fluid dynamics simulations were carried out to investigate cooling performance of water mist in heated chamber. The gas phase was prepared with natural convection heat transfer model for incompressible ideal case and then the effects of water mist injection characteristics on cooling capabilities were investigated upon the basis of the pre-determined temperature field. For the simulation of water mist behavior, Lagrangian discrete phase model was employed by using a commercial code, FLUENT. Smaller droplet sizes, greater injection angles and higher flow rates provided relatively higher cooling performance.

• Korean Chemical Engineering Research
• /
• 제49권5호
• /
• pp.554-559
• /
• 2011

리튬금속을 음전극으로 사용할 때의 안전성과 전극 특성을 개선하기 위해, 리튬금속 표면에 각기 종류가 다른 3가지의 탄소분말을 리튬금속 표면에 물리적으로 코팅한 전극을 제조하고 이를 리튬 2차전지의 음전극으로 채택하여 충방전 특성을 조사하였다. 일차입자의 입경이 작고 비표면적이 큰 탄소분말로 코팅한 음전극을 채택하는 경우가 충진밀도가 높고 표면 거칠기가 낮으며, 충방전 특성도 우수하게 나타났다. 이러한 탄소분말 코팅 효과는 소형 셀일수록 더욱 유리하게 나타났다.

• 열처리공학회지
• /
• 제28권4호
• /
• pp.181-189
• /
• 2015

Two types of advanced cold-work tool steels were characterized and compared. A higher-alloyed ledeburitic steel with primary carbides (denoted as 9Cr) and a lower-alloyed steel without primary carbides (5Cr) were fabricated by vacuum induction melting and subsequent hot forging. They were spheroidizing-annealed at $870^{\circ}C$, quenched at $1030^{\circ}C$ and tempered at 180 or $520^{\circ}C$. Their machinability after annealing and hardness, impact toughness, wear resistance after tempering were compared and interpreted in association with their characteristic microstructures. After annealing, 5Cr showed higher resistance to machining due to higher ductility and toughness in spite of lower strength and smaller carbide volume. Owing to smaller carbide volume fraction and the absence of coarse primary carbides, 5Cr showed even better impact toughness although the hardness was lower. The improved toughness of 5Cr resulted in excellent wear resistance, while smaller volume fraction of retained austenite also contributed to it.

• 복식문화연구
• /
• 제17권1호
• /
• pp.15-27
• /
• 2009

The purpose of this study was to find texture which suitable for the acryl knitted jacket of women in the middle age. The study was carried out 2 parts. The first part was to choose the pattern fitted in the body shape of women in the middle age, and the second part was wearing test with 3 different textured acryl knitted jacket(half milano, milano, jacquard). The usable data of the test were coded for further statistical analysis including descriptive statistics (frequency and one way-ANOVA test, Student-Newman-Keuls Multiple Range Test) by using SPSSWIN 12.0. The results were as follows: It was found that first evaluation for the appearance test on fitness, pattern B(Brand: Morado) were better than the rest of them(pattern A: Trieste, pattern C: Escalier). It was found that second evaluation for the test, jacket with jacquard were better than the rest of them. Acryl knitted Jacket of women in the middle age should made of jacquard. Therefore it should be designed as possible as considering the physical characteristics of knitted materials. It was found that third evaluation for the test, it was opposite results that a general knitted fabric pattern was made smaller than a woven jacket. So, it was necessary that the acryl knitted jacket of women in the middle age follow a similar site tolerance such as a woven jacket. This result was due to a radical change of a middle age women's body shape.