• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.343-347
• /
• 2003

Recently, the ratio of marine casualty has been marked about 72% in fishing boat and small ships which not less than 100 tons in Korea. It is mainly against navigation regulations such as look-out, selecting the ship's course and checking the ship's position according to the analysis of marine accident. In this paper, we proposes the Intelligent Navigation Guiding System(INGS) that provides an optimum route for an operator of small ships. INGS consists of program for route planning, interface module and GPS Plotter. we obtained optimum route from specific position to established route by INGS.

• Journal of Positioning, Navigation, and Timing
• /
• v.10 no.3
• /
• pp.229-234
• /
• 2021

In this paper, a study was conducted on the power amplifier control required to design an eLoran transmitter system using a low-height antenna. The eLoran transmitter developed during the eLoran technology development project conducted in Korea used a small 35 m antenna due to the difficulty of securing a site for antenna installation. This antenna height is very low compared to the height of 750 m which is required for eLoran 100 kHz signal transmission without any radiation loss. In the case of using such a small antenna, not only the radiation efficiency of the transmission is lowered, but also the power module control must be performed more precisely in order to transmit the eLoran standard signal. The equivalent RLC circuit of the transmitter system was implemented and transient analysis was conducted to derive the input required voltage for satisfying the output requirement. The voltage waveform was also generated by the RLC circuit analysis to generate the eLoran signal. Furthermore, we suggest power width modulation method to control eLoran power amplifier module more sophisticatedly.

• Journal of Ocean Engineering and Technology
• /
• v.37 no.1
• /
• pp.31-37
• /
• 2023

In this study, a fiber chain was developed to replace a steel chain using high-modulus polyethylene DM20. The pick count, wrapping count, and inner length were selected as the main design variables of the fiber chain and were analyzed to increase the breaking strength. Orthogonal array experiments were conducted, and the results were analyzed with respect to the breaking strength. The analysis revealed that the pick count and wrapping count had meaningful effects at significance levels within 5%. The main effect analysis revealed that a smaller pick count, larger wrapping count, and longer inner length caused the breaking strength to increase. With the wrapping count fixed at 1, a pick count less than -0.65, and an inner length greater than 0.38, the breaking strength was calculated to be greater than 300 kN. These results are expected be important factors in the derivation of an optimal combination of design variables to attain a fiber chain with a targeted strength.

• Journal of Fisheries and Marine Sciences Education
• /
• v.28 no.2
• /
• pp.539-549
• /
• 2016

This study analyzed ship's passing characteristics in relation with incoming and outgoing routes in Yeosu Gwangyang Port, and examined the risk factors and measures for safety management of marine traffic. The number of passing ships in Yeosu Gwangyang Port was about 60,000 ships annually based on 2014, and the tonnage rose 73% from 447,000 thousand tons in 2005 to 770,000 thousand tons in 2014. Actually, the number of large passing ships was revealed to enormously increase. As a result of marine traffic survey in Yeosu Gwangyang Port for three days in August 2015, daily average passing ships were 408 ships, and 77% of the total passing ships passed between 04:00 and 20:00. The chemical ships and general cargo ships took up the most at 58% of the total incoming and outgoing ships, followed by other work ships at 21%, tankers at 8%, fishing vessels at 7.5% and container ships at 5.5%. Concerning the size of passing ships, ships less than 1,000 tons accounted for 58.6% of the total passing ships. Ships of 1,000-5,000 tons were 20.1%, and those of 5,000-10,000 tons were 6.8%, and more than 10,000 tons were 14.4%. Especially, ships of 500 tons and less using mainly coastal passing routes took up 49% of the total passing ships. As for ship's passage ratio by route, Nakpo sea area where many routes meet accounted for 27.2%, specified area 49%, costal route 8%, specified area's incoming and outgoing sea area around Daedo 4.5%, and Dolsan coastal ara and Kumhodo sea area 8.5%. The number of ships standing by for anchoring in the six designated anchorages was 230 for three days. The standby rate for anchoring was 25% based on the specified area passing ships. In Nakpo sea area, where many routes meet, parallel passing and cross passing between ships occurred the most frequently. In the specified area, many cases, in which incoming and outgoing cargo ships at the starting and ending parts and incoming and outgoing work ships and fishing vessels at the coastal routes cross, took place. Consequently, the following measures are urgently needed: active passing management in the Nakpo sea area, where passing routes are complex, specified areas and costal traffic routes, the elimination of rocks in the route close to Myodo, an effort to improve routes including shallow depth area dredging, and rational safety management for small work ships frequently incoming and outgoing the passing routes of large ships, and fishing vessels operated in the sea areas around those passing routes.

• Journal of the Society of Naval Architects of Korea
• /
• v.60 no.6
• /
• pp.441-449
• /
• 2023

With the enforcement of environmental regulations by the International Maritime Organization, the market for eco-friendly ships is expanding, and ships using electric propulsion devices are emerging as a promising solution. Many studies have been conducted to predict the failure of ships, but most of them are mainly research on the main diesel engine of ships. As the ship's propulsion method changes, new data is needed to predict the failure of electric propulsion ships. In this paper aims to analyze the failure characteristics of the electric propulsion system in consideration of the difference in the type of failure between the internal diesel engine and the electric propulsion system. The ship's propulsion unit assumed a DC motor and a signal pattern for normal conditions and general failure modes, but the failure record of the electric propulsion device operated on the actual ship was not available, so it generated a failure signal for small electric motor equipment to identify the failure signal. Assuming unbalance, misalignment, and bearing failure, which are the primary failure modes of the ship's electric motor, a failure signal was generated using a "rotator vibration data generator," and the frequency band, size, and phase difference of the measured vibration signal were analyzed to analyze the characteristics of each failure condition. Finally, the characteristics of each failure condition were identified so that the signals according to the failure type could be classified.

• Journal of Navigation and Port Research
• /
• v.29 no.5 s.101
• /
• pp.383-388
• /
• 2005

To install a radar reflector on small ships, such as a small fishing vessel, a fishery buoy, and a barge ship for fishery, it is very important to develop the optimal system which may determine a proper installation location. For this, the response characteristics how waves have an effect on the small ships should be accurately analyzed. In this paper, we analyze the dynamic behaviors of small ships, which may be caused by irregular waves. To do this, we investigate how a barge ship responses to wavelength, water depth, and directions of incoming waves. The analyzed results shall be utilized to evaluate an effect on a radar cross section when we install an radar reflector on a barge ship for fishery and a small ship.

• Journal of Ocean Engineering and Technology
• /
• v.11 no.2
• /
• pp.131-137
• /
• 1997

The technology of small and medium sized shipbuilding companies is lower relatively to major shipbuilding companies, and should be up-graded from the viewpoint of national economic development. In spite that hul form design is one of the most important elements with respect to shipbuilding technology, small and medium sized shipbuilding companies are incapable of developing hull form. Inorder to support technically such companies hull form development was carried out for G/T 999ton class tanker and D/W 4990ton class tanker which are the typical vessels operating in coastal area. The operating efficiency for the developed hull forms are impeoved by 30% for G/T 999ton class tanker and 24% for D/W 4990 tonclass tanker respectively. The results of hull form development including ship model test and performance analysis are presented in this paper.

• Journal of the Korean Society of Industry Convergence
• /
• v.23 no.4_2
• /
• pp.661-667
• /
• 2020

The optimal shape modeling of core parts through 3D modeling and structural analysis for the development of small and medium-sized ships. The goal is to improve the efficient structure of the hydraulic system for controlling the rudder among the core steering parts in small and medium-sized ships. Through 3D modeling and structural analysis, a new concept of tiller parts and a double-acting hydraulic cylinder control system were proposed and operational structural stability was evaluated. Structural analysis of the three different tiller designs that can be replaceable onto existing fishing vessels was conducted to derive the final shapes. The emphasis was placed on evaluating the structural stability of the key drive components, the tiller, pin, and cylinder rodin the maximum torque condition of the hydraulic cylinder.

• Journal of Navigation and Port Research
• /
• v.27 no.3
• /
• pp.247-252
• /
• 2003

This paper is mainly concerned with the assessment of safe navigation between ships moving each other in restricted waterways. The numerical simulation of manoeuvring motion was conducted parametrically to propose an appropriate safe speed and distance, which is required to avoid sea accident under the different conditions, such as ship-velocity ratios, ship-length ratios, separation and stagger between ships. As for the calculation parameters, the ratios of velocity difference between two ships were considered as 0.6, 1.2, 1.5 and the ones of ship-length difference were regarded were regarded as 0.5, 1.0, 1.18. From the inspection of this investigation, it indicates the following result. Firstly, the separation between ships is more needed for the small vessel, compared to the large vessel. Secondly, the lateral distance between ships is necessarily required for the velocity ration of 1.2, compared to the cases of 0.6 and 1.5. The manoeuvring characteristics based on this investigation will be very useful for keeping the safety of navigation from the practical point of ships design and traffic control in confined water.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.6_3
• /
• pp.1305-1314
• /
• 2023

The global ship repair and modification market is expected to grow up to approximately $ 30 billion by 2025. Korea's shipbuilding industry is leading the world grounded on its international competitiveness in design and production technology. The reality, however, is that the ship repair and modification industry is centered on Gyeongnam, and there are only two to three ship repair workplaces that can repair large ships. Therefore, domestic ship repair companies target small and medium-sized ships mainly. This is because there are few workplaces equipped with a large dock in which large ships like LNG ships can be inspected regularly or repaired, complaints are severe for environmental problems, and related environmental regulations are so strict that it is very hard to obtain government approval for the extension of ship repair and modification workplaces or the opening of new shipbuilding sites. Besides, on account of the workers' high wages, few experts related, and higher ship repair price compared to that of Southeast Asia, most of the volume of repairing large ships including domestic LNG ships is being lost to Southeast Asian or Chinese markets. In this study, the work process and pre-work preparation process for ship hull (winch, windlass, hatch cover, ramp door, cargo gear, anchor chain) repair were analyzed and presented to foster domestic ship repair experts and revitalize related industries.