• Journal of Electrical Engineering and Technology
• /
• 제1권1호
• /
• pp.85-91
• /
• 2006

Recently, the reduction of electromagnetic vibration and noise of a capacitor motor (CRM) has become a very important subject from the standpoint of environmental improvement. Therefore, the authors have studied the characteristics of the dominant electromagnetic vibration of the CRM under load condition. In this paper, the effects of slot combination and skewed slot on the dominant electromagnetic vibration of a CRM under load condition are discussed both theoretically and experimentally. As a result, the characteristics of the dominant electromagnetic vibration for the slot combination and the reduction effect of the skewed slot on the electromagnetic vibration are clarified for a 4-pole CRM.

• Journal of Magnetics
• /
• 제21권1호
• /
• pp.78-82
• /
• 2016

Cogging torque will affect the performance of a permanent magnet Brushless DC Motor (BLDCM), thus the reduction of cogging torque is key for BLDCM optimization. In this paper, the phase shifting of cogging torque for a fractional-slot concentrated winding BLDCM is analyzed using the Maxwell tensor method. Moreover, a 9-slot 10-pole concentrated winding BLDCM driven by ideal square waveform is studied with the finite element method (FEM). An effective method to reduce the cogging torque is obtained by adjusting the slot opening. In addition, the influences of different slot openings on back electromotive force (back-EMF), air gap flux density and flux linkage are investigated and experimentally validated using the prototype BLDCM.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.74-76
• /
• 2002

Conventional integral slot design tend to have a high cogging torque and large end turns which contribute to copper losses. The fractional slot is more effective compared to integral slot in the cogging torque and EMF waveform. The effectiveness of fractional slot can be maximized by selecting optimal pole to slot ratio. This paper presents the effect of pole to slot ratio on the cogging torque and EMF waveform in the fractional slotted permanent magnet(PM) motor. The effectiveness of the proposed designs had been confirmed by comparing cogging torque, and EMF waveform between conventional and new models which are analyzed by Finite Element Method(FEM).

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.44-46
• /
• 2008

This paper presented the notch effect of interior permanent magnet motor(IPM) with compound variable number of pole and slot. The selection of proper pole and slot which makes characteristic and efficiency of motor is very important on motor design. The motor which has 6pole and 9slot is at base. This paper is choose the 4pole 6slot motor which has 2:3 ratio then analyzed the characteristic.

• 한국재료학회지
• /
• 제15권9호
• /
• pp.560-565
• /
• 2005

The objective of this paper is to decide optimal of the slot angle to minimize stress concentration in rotating disc of diamond saw. The fracture phenomena of the slot are discussed by the theoretical and experimental approaches and then some recommendation are presented to prevent the fracture. The focus of this investigation is to evaluation the effect of the slot on stress distribution using optimum design technique and finite element method(FEM) analysis. Stress concentration of the slot with respect to the various parameter of the slot such position, size, number, rotation speed. From the experimental results, when the slot angle of diamond saw is located $8^{\circ}\~12^{\circ}$ from rotating direction, the maximum equivalent stress reduces.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1998년도 특별강연 및 춘계학술발표 개요집
• /
• pp.46-48
• /
• 1998

• Journal of Periodontal and Implant Science
• /
• 제52권5호
• /
• pp.411-421
• /
• 2022

Purpose: In this study, we aimed to evaluate the degree of heat generation when a novel drill design with an irrigation slot was used with metal sleeve-free (MF) and metal sleeve-incorporated (MI) surgical guides in an environment similar to that of the actual oral cavity. Methods: A typodont with a missing mandibular right first molar and 21 bovine rib blocks were used. Three-dimensional-printed MF and MI surgical guides, designed for the placement of internal tapered implant fixtures, were used with slot and non-slot drills. The following groups were compared: group 1, MI surgical guide with slot drill; group 2, MI surgical guide with a non-slot drill; and group 3, MF surgical guide with a slot drill. A constant-temperature water bath at 36℃ was used. The drilling was performed in 6 stages, and the initial, highest, and lowest temperatures of the cortical bone were measured at each stage using a non-contact infrared thermometer. Results: There were no temperature increases above the initial temperature in any drilling procedure. The only significant difference between the non-slot and slot groups was observed with the use of the first drill in the MI group, with a higher temperature in the non-slot group (P=0.012). When the heat generation during the first and the second drilling was compared in the non-slot group, the heat generation during the first drilling was significantly higher (P<0.001), and there was no significant difference in heat generation between the drills in the slot group. Conclusions: Within the limitations of this study, implant-site preparation with the surgical guide showed no critical increase in the temperature of the cortical bone, regardless of whether there was a slot in the drill. In particular, the slotted drill had a cooling effect during the initial drilling.

• Journal of information and communication convergence engineering
• /
• 제14권2호
• /
• pp.65-70
• /
• 2016

This paper proposes and experimentally tests a modified circular slot antenna fed by a fork-like tuning stub for ultra-wideband (UWB) operation. The proposed antenna consists of a modified circular slot model and fork-like tuning stub. The proposed antenna is printed on a 34.0 mm × 30.0 mm FR4 substrate with thickness of 1.0 mm and relative permittivity of 4.4. The effect of various parameters of the circular slot and fork-like tuning stub is investigated for UWB operation. The modified circular slot and fork-like tuning stub are fabricated on the substrate to achieve wideband operation and good impedance matching. Experimental results demonstrated that the measured return loss exhibits an acceptable agreement with the simulated return loss and satisfies the -10 dB impedance bandwidth requirement while simultaneously covering the UWB bands. In addition, the proposed antenna shows good radiation characteristics and gains in the UWB bands.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.472-475
• /
• 2005

In this study, the equivalent physical properties of the shield-slot plate that has a lot of very tiny bridge shape structures on its plane were determined by tensile tests and structural analyses. With those results in hand, numerical analyses for the deflection profile by gravity effect were carried out to compare with experimental results. The two results were shown coincident very well so that the estimated equivalent physical properties were verified enough for further studies such as curvature reduction for the shield-slot plate.

• 화약ㆍ발파
• /
• 제28권2호
• /
• pp.50-58
• /
• 2010

본 연구는 아직 국내에서 연구가 미비한 분야인 슬롯드릴링 공법에 대해 분석한 것이며 슬롯드릴링 공법을 공사현장에서 적용할 수 있는 이론적인 기반을 마련하고자 하였다. 본 연구는 슬롯드릴링 공법을 통해 진동저감의 가능성을 제안한다. 수치해석을 통해 슬롯드릴링의 유효제원 관해 크게 두 가지를 분석 하였다. 하나는 슬롯과 진원 사이의 거리에 따른 진동속도의 변화를 분석이며 다른 하나는 진동제어를 위한 적절한 크기의 슬롯너비와 슬롯높이를 찾고자 하였다. 결론적으로 진원과 슬롯사이의 거리가 멀어질수록 진동저감 효과가 감소함을 알 수 있었다. 그리고 슬롯제원의 변화에 따른 임의의 계측지점에서의 진동속도에 대한 영향도 확인할 수 있었다.