• Proceedings of KOSOMES biannual meeting
• /
• 2009.06a
• /
• pp.85-86
• /
• 2009

The sloshing phenomenon can be defined as the nonlinear movement of the free-surface of liquids inside tanks. It generates dynamic loads on the tank structure and thus becomes a problem of relative importance in the design of marine structures. The present study describes a experiment of the sloshing of flows with free-surface which contained in a rectangular tank moving in pitching motion.

• International Journal of Ocean System Engineering
• /
• v.3 no.4
• /
• pp.225-230
• /
• 2013

This paper introduces the experimental results of sloshing model tests carried out at Seoul National University. Two 1/50-scale tanks, i.e., 2D and 3D models with the same shape, were manufactured for the comparative study. Particular interest was taken in the differences in impact pressures between the 2D and 3D models. Regular motion tests were conducted for different filling depths. For each filling depth, 500 cycles of regular excitation were imposed at each frequency. To observe the characteristics and severity of sloshing from the acquired pressure data, statistical analyses were performed, not only for the peak pressure, but also for the area-concept indices, which represented the amount of impulse.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.8 no.5
• /
• pp.434-441
• /
• 2016

Numerical simulations of 1D Burgers equation and 2D sloshing problem were carried out to study numerical discrepancy between serial and parallel computations. The numerical domain was decomposed into 2 and 4 subdomains for parallel computations with message passing interface. The numerical solution of Burgers equation disclosed that fully explicit boundary conditions used on subdomains of parallel computation was responsible for the numerical discrepancy of transient solution between serial and parallel computations. Two dimensional sloshing problems in a rectangular domain were solved using OpenFOAM. After a lapse of initial transient time sloshing patterns of water were significantly different in serial and parallel computations although the same numerical conditions were given. Based on the histograms of pressure measured at two points near the wall the statistical characteristics of numerical solution was not affected by the number of subdomains as much as the transient solution was dependent on the number of subdomains.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.10a
• /
• pp.534-537
• /
• 2012

Hydroelastic effects on sloshing phenomena in a rectangular tank are numerically investigated. The dimension of the tank is $1000mm{\times}600mm$, and the filling ratio of water is 20% of tank height. One of the side walls of tank is assumed to be flexible. The tank is excited into sway motion with amplitude of 100mm and frequency of 0.53Hz that is first natural frequency of water inside the tank. Prediction results for time histories of pressure and displacement of flexible and rigid walls are compared to quantitatively assess hydroelastic effects on sloshing phenomena.

• Structural Engineering and Mechanics
• /
• v.16 no.4
• /
• pp.423-440
• /
• 2003

Arbitrary Lagrangian Eulerian finite element methods gain interest for the capability to control mesh geometry independently from material geometry, the ALE methods are used to create a new undistorted mesh for the fluid domain. In this paper we use the ALE technique to solve fuel slosh problem. Fuel slosh is an important design consideration not only for the fuel tank, but also for the structure supporting the fuel tank. "Fuel slosh" can be generated by many ways: abrupt changes in acceleration (braking), as well as abrupt changes in direction (highway exit-ramp). Repetitive motion can also be involved if a "sloshing resonance" is generated. These sloshing events can in turn affect the overall performance of the parent structure. A finite element analysis method has been developed to analyze this complex event. A new ALE formulation for the fluid mesh has been developed to keep the fluid mesh integrity during the motion of the tank. This paper explains the analysis capabilities on a technical level. Following the explanation, the analysis capabilities are validated against theoretical using potential flow for calculating fuel slosh frequency.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2011.04a
• /
• pp.544-551
• /
• 2011

As the cargo tank size and configuration of Liquefied Natural Gas carriers(LNGC) grows in response to the global increase in demands for LNG and the necessities of its economical transportation, impact loading from sloshing may become one of the most important factors in the structural safety of LNG Cargo Containment Systems(CCS). The objective of this study is to demonstrate the procedure of the structural safety assessment of MARK III membrane type CCS under sloshing impact loading using local zooming analysis technique of LS-DYNA code.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2011.04a
• /
• pp.557-560
• /
• 2011

In the present paper, the sloshing resistance performance of an LNG carrier insulation system is evaluated by fluid-structure interaction (FSI) analysis. For this analysis, the arbitrary Lagrangian Eulerian (ALE) method is adopted to accurately calculate the structural behavior induced by internal LNG motion of a KC-1 type LNG carrier cargo tank. In addition, the global-local analysis method is introduced to reduce computational time and cost. The global model is built from shell elements to reduce the sloshing analysis time. The proposed novel analysis techniques can potentially be used to evaluate the structural integrity of LNG carrier insulation systems.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2401-2405
• /
• 2008

In the present study, a three-dimensional least square/level set based two-phase flow code was developed for the simulation of three-dimensional sloshing problems using finite element discretization. The present method can be utilized for the analysis of a free surface flow problem in a complex geometry due to the feature of FEM. Since the finite element method is employed for the spatial discretization of governing equations, an unstructured mesh can be naturally adopted for the level set simulation of a free surface flow without an additional load for the code development except that solution methods of the hyperbolic type redistancing and advection equations of the level set function should be devised in order to give a bounded solution on the unstructured mesh. From the numerical experiments of the present study, it is shown that the proposed method is both robust and accurate for the simulation of three-dimensional sloshing problems.

• Journal of the Korean Society for Precision Engineering
• /
• v.8 no.1
• /
• pp.96-104
• /
• 1991

This study is concerned with the fluid sloshing dampers to suppress the high vibration in the resonance and operating regions. An experimental investigation was conducted to determine the logarithmic decrement, natural frequency, tuning frequency ratio of oscillation of liquids contained in an spherical rigid container. The decay of the vibration amplitude was studied for the range of liquid filling ratio in container. The results of the investigation indicate that the sloshing motion of liquids results in an increase in the available effective damping when the filling ratio is in the region near H/R=1.3-1.6.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.1097-1100
• /
• 2004

In this study the fluid-solid coupling(sloshing) behavior of the tanker-lorry during turning are investigated numerically. The ALE numerical method is used as sloshing analysis algorithm and numerical simulation is conducted for the various fluid filling height 25%, 50% and 75%. The forces for radial and vertical direction are calculated and compared for various fluid-filling heights. From the analysis results, in case of 25% filling, the sloshing effect is the most highest.