• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1996년도 제23회 학술대회
• /
• pp.7-16
• /
• 1996

Rapid increase of refrigeration & air-conditioning system( r & a system ) in modern industries brings attention to the urgency of development as a core technology in the area. And it required to the compatibility problem of r & a system to alternative refrigerant for the protection of environment. Then, it is requested to research about the lubrication characteristics of refrigerant compressor which is the core thechnology in the r & a system. The study of lubrication characteristics in the critical sliding component is essential for the design of refrigerant compressor. Therefore, theoetical investigation of the lubrication characteristics of rotary compressor for r & a system is studied. And the Runge-Kutta method is used for the analysis of the behavior of rolling piston in the rotary compressor. The results show that the rotating speed of shaft and the discharge pressure have an important effect upon the angular velocity of the rolling piston. This results give important basic data for the further lubrication analysis and design of the rotary compressor.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 제5회 박판성형 SYMPOSIUM
• /
• pp.99-102
• /
• 2006

In the present study, the blow forming characteristics of AZ31 sheet was investigated to test the feasibility of the practical application of wrought Mg alloys. Mg alloys have drawn a huge attention in the field of transportation and consumer electronics industries since it is the lightest alloy which could be industrially applicable. Most Mg alloy components have been fabricated by casting method. However, there have been a lot of research activities on the wrought alloys and their plastic forming process recently. Shallow cups for the small electronics cases have been stamped with warm die system. However, some technical issues will challenge Mg forming when large parts are considered with warm die system over $200^{\circ}C$. Most of all, thermal expansion of die system will deteriorate a die accuracy. On the other hand, blow forming does not have a problem with inaccuracy with die system. In this study, tensile tests were followed by blow forming at various temperature and pressure. AZ31 sheet showed a superplastic deformation behavior with extensive grain boundary sliding at the temperature above $300^{\circ}C$. However, the deformation behavior was likely to differ depending on stress condition.

• Journal of Mechanical Science and Technology
• /
• 제20권11호
• /
• pp.1980-1992
• /
• 2006

Nucleate pool boiling experiments were performed using pure R11 for various surface angles under constant heat flux conditions during saturated pool boiling. A 1-mm-diameter circular heater with an artificial cavity in the center that was fabricated using a MEMS technique and a high-speed controller were used to maintain the constant heat flux. Bubble growth images were taken at 5000 frames per second using a high-speed CCD camera. The bubble geometry was obtained from the captured bubble images. The effects of the surface angle on the bubble growth behavior were analyzed for the initial and thermal growth regions using dimensional scales. The parameters that affected the bubble growth behavior were the bubble radius, bubble growth rate, sliding velocity, bubble shape, and advancing and receding contact angles. These phenomena require further analysis for various surface angles and the obtained constant heat flux data provide a good foundation for such future work.

• 터널과지하공간
• /
• 제9권1호
• /
• pp.56-63
• /
• 1999

암석은 불연속면들에 의해 다양한 방식의 거동을 보인다. 이러한 암석의 복잡한 파괴와 변형거동을 해석하기 위한이전의 많은 연구들은 균열모델의 개발에 중점을 두었다. 본 연구에서는 석탄과 같은 파쇄 암석에 대해 활주균열모형과 전단균열모형의 타당성을 검토하였고 모델을 수치해석에 적용하였다. 수치해석을 수행하기 위해 여러 방식으로 유한 요소 프로그램을 수정하였다. 2차원 해석에서 횡등방성을 설명하기 위하여 대칭축의 방향에 대해 응력-변형률 관계를 수정하였고, 균열성장에 따른 유효탄성계수의 변화를 계산하였다. 2차원 실내 단축압축시험의 가단한 예를 해석하였으며 해석결과는 실내시험에서 구한 결과와 일치하였다.

• 한국농공학회지
• /
• 제41권6호
• /
• pp.64-74
• /
• 1999

The frequency of earthquake occurrence tends to increase in Korea. Therefore, the stability of pipeline, such as watersupply pipe, gas pipe, and oil pipe etc. across fault zones in Gyoung-sang landmass is very important, expecially , in metropolitan area. There were some examples of the construction of buried pipeline across fault zones in Korea. the interactiion between the buried pipeline across fault zones and the ground is considered. As well, in the interfaces of them, the direct shear numerical analysis model including elasto-plastic joint element is assumed that the retained dilatancy theory in them, otherwise. Also, the other elements are modeled the ground is nonlinear elastic coutinuaus beam, respectively. In this study, the maximum shear force point exist inside retaine zone(anchored zone) during shwar (as fault sliding), and the distribution of pipeline's behavior is all alike them of pipeline buried in ladnsliding grounds. Since the pipeline is not continuous beam but jointed by steel-pipe segments , practically, on acting of a large bending moment or a shear force, then, those are may be unstable. The reaearch on this point may be new approach.

• 대한기계학회논문집A
• /
• 제31권2호
• /
• pp.197-204
• /
• 2007

Fretting is a contact damage process that occurs between two contact surfaces. Fretting fatigue reduces fatigue strength of the material due to low amplitude oscillatory sliding and changes in the contact surfaces of strongly connected machine and structure such as bolt, key, pin, fixed rivet and connected shaft, which have relative slip of repeatedly extreme low frequency amplitude. In this research, the fretting fatigue behavior of 2024-T3511 and 7050-T7451 aluminum alloys used mainly in aircraft and automobile industry were experimentally estimated. Based on this experimental wort the following results were obtained: (1) A significant decrease of fatigue lift was observed in the fretting fatigue compared to the plain fatigue. The fatigue limit of 2024-T3511 aluminum alloy decreased about 59% while 7050-T7451 aluminum alloy decreased about 75%. (2) In 7050-T7451 specimen using ATSI4030 contact pad, crack was initiated more early stage than using 2024-T3511 contact pad. (3) In all specimens, oblique cracks were initiated at contact edge. (4) Tire tracks and rubbed scars were observed in the oblique crack region of fracture surface.

• Bulletin of the Korean Chemical Society
• /
• 제30권4호
• /
• pp.907-912
• /
• 2009

Complex breakup behavior in the revival wave has been observed in the Belousov-Zhabotinsky(BZ) reaction system containing 1,4-cyclohexanedione (1,4-CHD) in the dish divided into two compartments with a sliding window. A same reaction mixture is poured into the two compartments individually with time difference. Wave propagation exhibited different behavior in the revival wave of the reaction system. This was largely dependent on the progress time prior to the pouring into each compartment and on the gap between the times of pouring into the two compartments. The revival wave in the reaction system is induced spontaneously as a new wave train with a long time lag after the disappearance of the initially induced wave. A thoroughgoing study of the chaotic breakup of propagating chemical wave train was to be possible since the revival wave has a longer wavelength, clearer wave-train patterns, and longer duration period.

• KSTLE International Journal
• /
• 제6권2호
• /
• pp.45-50
• /
• 2005

Plasma ceramic spray that is applied on a machine part under severe work conditions has been investigated for tribological behavior. The application of ceramic coatings by plasma spray has become essential in tribosystems to produce wear resistance and long life in severe conditions. The purpose of this study was to investigate the wear characteristics of $8\%Y_{2}O_3-ZrO_2$ coating, in view of the effect of post-spay heat treatment. The plasma-sprayed $8\%Y_{2}O_3-ZrO_2$ coating was studied to know the relationship between phase transformations and wear behavior related to post-spray heat treatment. Wear test was carried out with ball on disk type on normal loads of 50N,70N and 90N under room temperature. The phase transformation of phase and the value of residual stress were measured by X-ray diffraction method(XRD). Tribological characteristics and wear mechanisms of coatings were observed by SEM. The tribological wear performance was discussed in the focusing of residual stress. Consequently, post-spray heat treatment plays an important role in decreasing residual stress. Residual stress in the coating system has a significant influence on the wear mechanism of coating.

• 대한조선학회논문집
• /
• 제53권2호
• /
• pp.162-169
• /
• 2016

A new concept of membrane type LNG CCS was proposed. Also, its static behavior was numerically analyzed considering the interaction between primary and secondary barrier together with securing device. Hull deflection was taken into account as an external load, together with temperature distribution across the barriers. The suggested numerical model considers both sliding and contact between the two mating surfaces of both the primary and secondary barrier, and anisotropic material behavior of plywood, R-PUF was also taken into account. Furthermore, detailed local strength was evaluated for the securing device, which is arranged between two barriers to hold the primary barrier. It was confirmed through the numerical analysis that the new concept of membrane type CCS was structurally safe under static loading condition and securing concept was structurally reliable.

• 콘크리트학회논문집
• /
• 제19권4호
• /
• pp.433-439
• /
• 2007

본 연구는 하나의 프리캐스트 거더를 분할하여 세그먼트로 각각 공장에서 제작하여 현장으로 운반한 후 포스트텐션 방식으로 체결하여 가설하는 분절공법으로 제작된 철도교 조립식 콘크리트 박스 거더의 정적 성능을 검증하고자 한다. 길이 20m의 실물 조립식 콘크리트 거더를 3등분으로 분절하여 제작한 후, 정적 성능 검증을 위해 같은 제원의 일체 거더와 동일한 조건에서 재하 실험을 수행하였다. 분절 거더 및 일체 거더에 대해 중앙 처짐, 단부 회전각, 균열 양상 등을 비교하였다. 또한 분절 거더의 접합부 거동을 모니터링하기 위해서 수직 상대 변위 및 수평 상대 변위를 최대 재하 하중까지 측정하였다. 분절 거더의 처짐은 육안으로 균열이 감지되는 균열하중 이상부터 일체 거더보다 상대적으로 크게 발생하고 있음을 알 수 있었다. 그러나 분절 거더는 균열하중에 도달하기 전까지 일체 거더와 동일한 거동을 보였다. 또한 분절부의 전단변형 여부를 조사하기 위한 수직 및 수평 상대 변위를 측정한 결과, 최종 재하 하중까지 전단에 의한 변형이 발생하지 않고 있음을 확인하였다. 또한 각 하중단계 별로 비교한 균열 양상은 분절 거더가 일체 거더와 같이 휨에 의한 사인장균열의 형태로 파괴가 진행되고 있음을 보였다.