• Journal of the Semiconductor & Display Technology
• /
• v.22 no.3
• /
• pp.21-27
• /
• 2023

In this article, a plate-type megasonic cleaning system with cooling pins is proposed for the sliced ingot, which is a raw material of silicon (Si) wafers. The megasonic system is operated with a lead zirconate titanate (PZT) actuator, which has high electric resistance, thus when it is being operated, it dissipates much heat. So this article proposes a megasonic system with cooling pins. In the design process, finite element analysis was performed and the results were used for the design of the waveguide. The frequency with the maximum impedance value was 998 kHz, which agreed well with the measured value of 997 kHz with 0.1 % error. Based on the results, the 1 MHz waveguide was fabricated. Acoustic pressures were measured, and analyzed. Finally, cleaning tests were performed, and 90 % particle removal efficiency (PRE) was achieved over 10 W power. These results imply that the developed 1 MHz megasonic will effectively clean sliced ingot wafer surfaces.

• Nuclear Engineering and Technology
• /
• v.56 no.3
• /
• pp.1013-1021
• /
• 2024

A series of experiments were performed to produce a fuel source for a molten salt reactor (MSR) through pyroprocessing technology. A simulated LiCl-KCl-UCl₃-NdCl₃ salt system was prepared, and the U element was fully recovered using a liquid cadmium cathode (LCC) by applying a constant current. As a result, the salt was purified with an UCl₃ concentration lower than 100 ppm. Subsequently, the U/RE ingot was prepared by melting U and RE metals in Y₂O₃ crucible at 1473 K as a surrogate for RE-rich ingot product from pyroprocessing. The produced ingot was sliced and used as a working electrode in LiCl-KCl-LaCl₃ salt. Only RE elements were then anodically dissolved by applying potential at - 1.7 V versus Ag/AgCl reference electrode. The RE-removed ingot product was used to produce UCl₃ via the reaction with NH4Cl in a sealed reactor.

• Korean Journal of Materials Research
• /
• v.16 no.2
• /
• pp.75-79
• /
• 2006

The effect of ozone and/or ultrasound treatments on the efficiency of slurry removal in post sliced cleaning (PSC) of silicon ingot was studied. Efficiency of slurry removal was evaluated as functions of time, temperature and surfactant with DOE (Design of Experiment) method. Residual slurries were observed on the wafer surface in case of cleaning by ozone or ultrasound separately. However, a clean wafer surface was appeared when cleaned with ozone and ultrasound simultaneously. It has found that cleaning time was the main effect among temperature, time and surfactant. Elevated temperature, addition of surfactant and high ozone concentration helped to accelerate efficient removal of slurry. The improvement of removal efficiency seems to be related to the formation of more active OH radicals. The highly cleaned surface was achieved at 10 wt% ozone, 1 min and 10 vol% surfactant with ultrasound. Application of ozone and ultrasound might be a useful method for PSC process in wafer cleaning.

• 전기의세계
• /
• v.21 no.1
• /
• pp.17-21
• /
• 1972

Electrical resistivity and switching phenomena in glass semiconductor of AsTe and AsTeGa is studied. Samples sliced from ingot which is air quenched or water quenched, show high resistivity at room temperature. The resistivity of the AsTe and AsTeGa is 1*10$^{6}$ .ohm.-cm and 5*10$^{6}$ .ohm.-cm at 27.deg. C. Switching phenomena take place in thin the thick samples. Holding voltage is different with the thickness of the samples and the characteristics of switching in the thin and thick samhles are similar. When square wave pulse voltage is applied, delay time is detected to 5.mu.sec by oscilloscpoe.

• Korean Journal of Materials Research
• /
• v.22 no.9
• /
• pp.450-453
• /
• 2012

In crystalline solar cells, the substrate itself constitutes a large portion of the fabrication cost as it is derived from semiconductor ingots grown in costly high temperature processes. Thinner wafer substrates allow some cost saving as more wafers can be sliced from a given ingot, although technological limitations in slicing or sawing of wafers off an ingot, as well as the physical strength of the sliced wafers, put a lower limit on the substrate thickness. Complementary to these economical and techno-physical points of view, a device operation point of view of the substrate thickness would be useful. With this in mind, BC-BJ Si and GaAs solar cells are compared one to one by means of the Medici device simulation, with a particular emphasis on the substrate thickness. Under ideal conditions of 0.6 ${\mu}m$ photons entering the 10 ${\mu}m$-wide BC-BJ solar cells at the normal incident angle (${\theta}=90^{\circ}$), GaAs is about 2.3 times more efficient than Si in terms of peak cell power output: 42.3 $mW{\cdot}cm^{-2}$ vs. 18.2 $mW{\cdot}cm^{-2}$. This strong performance of GaAs, though only under ideal conditions, gives a strong indication that this material could stand competitively against Si, despite its known high material and process costs. Within the limitation of the minority carrier recombination lifetime value of $5{\times}10^{-5}$ sec used in the device simulation, the solar cell power is known to be only weakly dependent on the substrate thickness, particularly under about 100 ${\mu}m$, for both Si and GaAs. Though the optimum substrate thickness is about 100 ${\mu}m$ or less, the reduction in the power output is less than 10% from the peak values even when the substrate thickness is increased to 190 ${\mu}m$. Thus, for crystalline Si and GaAs with a relatively long recombination lifetime, extra efforts to be spent on thinning the substrate should be weighed against the expected actual gain in the solar cell output power.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.10
• /
• pp.799-802
• /
• 2011

In this study, SiC single-crystal ingots were prepared on two seed crystals with different doping level by using the physical vapor transport (PVT) technique; then, SiC crystal wafers sliced from the grown SiC ingot were systematically investigated to find the effect of seed doping level on the doping concentration and crystal quality of the SiC. To exclude extra effects induced by adjustment of the process parameters, we simultaneously grew the SiC crystals on two seed crystals with different level, which were fabricated from previous two SiC crystal ingots.