• Proceedings of the KIEE Conference
• /
• 2004.11a
• /
• pp.82-85
• /
• 2004

In this study, in order to increase piezoelectric properties of the low temperature sintering ceramics for multilayer piezoelectric transformer, PCW-PMN-PZT ceramics added with $Li_2CO_3$, $Bi_2O_3$ and CuO as sintering aids were manufactured according to the amount of $MnO_2$ addition, and their microstructural, dielectric and piezoelectric properties were investigated. When the sintering aids was added, specimens could be sintered at $950^{\circ}C$. However, sintering aids added specimens showed lower piezoelectric properties than those of non-added specimens. $0.1wt%MnO_2$ added specimen at $950^{\circ}C$ showed ${\varepsilon}_r$, of 1503, $k_p$ of 0.57 and $Q_m$ of 1502 were shown, respectively, and showed optimum properties for multilayer piezoelectric transformer.

• Journal of Powder Materials
• /
• v.7 no.4
• /
• pp.218-227
• /
• 2000

It is well known that the Cu-Cr alloys are very difficult to be made by conventional sintering methods. This difficulty originates both from limited solubility of Cr in the Cu matrix and from limited sintering temperature due to high vapor pressures of Cr and Cu components at the high temperature. Densification of Cu-50%Cr Powder compacts by conventional Powder metallurgy Process has been studied. Three kinds of sintering methods were tested in order to obtain high-density sintered compacts. Completely densified Cu-Cr compacts could be obtained neither by solid state sintering method nor by liquid phase sintering method. Both low degree of shrinkage and evolution of large pores in the Cu matrix during the solid state sintering are attributed to the anchoring effect of large Cr particles, which inhibits homogeneous densification of Cu matrix and induces pore generation in the Cu matrix. In addition, the effect of undiffusible gas coming from the reduction of Cu-oxide and Cr-oxide was observed during liquid phase sintering. A two-step sintering method, solid state sintering followed by liquid phase sintering, was proved to have beneficial effect on the fabrication of high-dendsity Cu-Cr sintered compacts. The sintered compacts have properties similar to those of commercial products.

• Journal of Powder Materials
• /
• v.5 no.4
• /
• pp.286-292
• /
• 1998

Ni$_3$Al intermetallic compound has been tested as a binder phase, in order to improve the oxidation resistance and the mechanical properties of TiC-Ni cermet at a high temperature. The wettability of $Ni_3Al$ on TiC and the optimum sintering condition were investigated in TiC-(30, 40) vol% $Ni_3Al$ cermets with the sintering temperature (1380~$1430^{\circ}C$) and time (30~99 min). The results are summarized as follows: 1) Ni$_3$Al showed good wettability on TiC above 1400$^{\circ}C$ ; 2) The shrinkages of the specimens increased with the sintering temperature, the sintering time and the binder content, whereas the relative densities were decreased; 3) Any other phase did not appeared in the microstructures of all sintered cermets. The grain sizes of TiC became larger as the sintering temperature and the sintering time as well as the binder content increased; 4) The hardness of the cermets decreased with increase in the sintering temperature and the sintering time as well as the binder content; 5) The transverse-rupture strength of the cermets increased with the sintering temperature and the sintering time, whereas it decreased with the binder content.

• The Journal of Advanced Prosthodontics
• /
• v.16 no.1
• /
• pp.25-37
• /
• 2024

PURPOSE. To investigate the effect of sintering programs and surface treatments on surface properties, phase transformation and flexural strength of monolithic zirconia. MATERIALS AND METHODS. Zirconia specimens were sintered using three distinct sintering programs [classic (C), speed (S), and superspeed (SS)] (n = 56, each). One sample from each group underwent scanning electron microscopy (SEM) and grain size analysis following sintering. Remaining samples were divided into five subgroups (n = 11) based on the surface treatments: control (CL), polish (P), glaze (G), grind + polish (GP), and grind + glaze (GG). One sample from each subgroup underwent SEM analysis. Remaining samples were thermally aged. Monoclinic phase volume, surface roughness, and three-point flexural strength were measured. Monoclinic phase volume and surface roughness were analyzed by Kruskal-Wallis and Dunn tests. Flexural strength was analyzed by two-way ANOVA and Weibull analysis. The relationships among the groups were analyzed using Spearman's correlation analysis. RESULTS. Sintering program, surface treatment, and sintering × surface treatment (P ≤ .010) affected the monoclinic phase volume, whereas the type of surface treatment and sintering × surface treatment affected the surface roughness (P < .001). Type of sintering program or surface treatment did not affect the flexural strength. Weibull analysis revealed no significant differences between the m and σ_o values. Monoclinic phase volume was positively correlated with surface roughness in the SGG and SSP groups. CONCLUSION. After sintering monolithic zirconia in each of the three sintering programs, each of the surface treatments can be used. However, for surface quality and aging resistance, G or GG can be recommended as a surface finishing method.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1200-1201
• /
• 2006

Attempts have been made to describe the influence of production process parameters on the microstructure and properties of W-Ag and Mo-Ag composites. The compositions of powder mixtures are W+30% Ag and Mo+30%Ag. Silver additions assists densification during sintering by a liquid phase sintering process. The main goal of this work is to compare properties and microstructure of as-sintered and as-infiltrated composites.

• Journal of Korea Foundry Society
• /
• v.10 no.1
• /
• pp.64-70
• /
• 1990

In order to lower the cabon content of sintered products below the solubility of austenite, Fe-oxide was added to cast iron powder of which matrix was pearlite. And the effects of it on some sintering properties and mechanical properties were investigated. Roughly speaking, the linear shrinkage, density, and tensile strendth of sintered properties increased as the sintering temperature became higher, the size distribution of powder became finer, and the amount of Fe-oxide added became less. The maximum tensile strength of sintered products was $78㎏f/mm^2$ more or less, of which carbon content was 1.4% and sintering temperature was $1180^{\circ}C$.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.2
• /
• pp.183-191
• /
• 1990

Polycrystalline CdS film have been prepared by coating a slurry constiting of CdS, CdCl2, various amount of InCl3 and propylene glycol on glass substrate and by sintering in a nitrogen atmosphere, and their sintering behaviors, electrical properties and optical properties have been investigated. As the amount of InCl3 increases, the enhancing effect of CdCl2 on sistering decreses resulting in a sharp decrease in optical transmittance and an increase in electrical resistivity. The carrier concentration is almost independent of InCl3 added due to the occurrence of chlorine doping and to the compensating effect of indium dopant. Microstructure an optical properties of CdS film, which contain CdCl2 and InCl3 before sintering, can be improved by sintering in a sealed boat.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.765-766
• /
• 2006

[ $Mo_2FeB_2$ ] boride base cermets produced by a novel sintering technique, called reaction boronizing sintering through a liquid phase, have excellent mechanical properties and wear and corrosion-resistances. Hence, the cermets are applied to the injection molding die-casting machine parts and so on. We investigated that the effect of deoxidization and sintering temperature on mechanical properties and deformation of the MIM processed cermets. As a result, deoxidization temperature of 1323K and sintering temperature of 1518K were suitable. The MIM products of the cermets showed allowable dimensional accuracy and the same mechanical properties as the press-sintered ones.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.7
• /
• pp.543-546
• /
• 2011

We studied sintering temperature to enhance the piezoelectric properties of $0.98(Na_{0.5}K_{0.5})NbO_3-0.02Li(Sb_{0.17}Ta_{0.83})O_3$+0.01wt%ZnO (hereafter NKN-LST+ZnO) lead free piezoelectric ceramics. The synthesis and sintering method were the conventional solid state reaction method and sintering was executed at $1,080\sim1,120^{\circ}C$. We found that NKN-LST+ZnO ceramics at optimal sintering temperature showed the improved piezoelectric properties at the optimal sintering temperature. The NKN-LST+ZnO ceramics show good performance with piezoelectric constant $d_{33}$= 153 pC/N sintered at $1,090^{\circ}C$. The results reveal that NKN-LST+ZnO ceramics are promising candidate materials for lead-free piezoelectric application.

• Journal of the Korean Ceramic Society
• /
• v.27 no.3
• /
• pp.337-344
• /
• 1990

As a function of sintering temperature and time, the electrical properties of ruthenium based thick film resistors were investigated with microstructure. The variatio of resistivity and TCR(temperature coefficient of resistance)trends of sintered speciman at various sintering temperature were different low resistivity paste(Du Pont 1721) from high one(Du Pont 1741). These phenomena are deeply relative to microstructure of sintered film. With increasing the sintering temperature for 1721 system, the electrical sheet resistivity decreased, but again gradually increased above 80$0^{\circ}C$. And TCR trends in 1721 system are all positive. On the other hand the electrical sheet resistivity of 1741 resistor system decreased with sintering temperature. And TCR trends variable according to sintering temperature. TCR of speciman sintered at $700^{\circ}C$ was negative value, and TCR of 80$0^{\circ}C$ sintered speciman coexisted negative and positive value. But in case of speciman sintered at 90$0^{\circ}C$, TCR was positive value. As results of this fact, it was well known that the charge carrier contributied to electrical conduction in 1741 resistor system varied with sintering temperature.