• Journal of Powder Materials
• /
• v.23 no.3
• /
• pp.221-227
• /
• 2016

Waste oyster shells create several serious problems; however, only some parts of them are being utilized currently. The ideal solution would be to convert the waste shells into a product that is both environmentally beneficial and economically viable. An experimental study is carried out to investigate the recycling possibilities for oyster shell waste. Bulk ceramic bodies are produced from the oyster shell powder in three sequential processes. First, the shell powder is calcined to form calcium oxide CaO, which is then slaked by a slaking reaction with water to produce calcium hydroxide $Ca(OH)_2$. Then, calcium hydroxide powder is formed by uniaxial pressing. Finally, the calcium hydroxide compact is reconverted to calcium carbonate via a carbonation reaction with carbon dioxide released from the shell powder bed during firing at $550^{\circ}C$. The bulk body obtained from waste oyster shells could be utilized as a marine structural porous material.

• Journal of Powder Materials
• /
• v.27 no.3
• /
• pp.256-267
• /
• 2020

Metal additive manufacturing (AM) technologies are classified into two groups according to the consolidation mechanisms and densification degrees of the as-built parts. Densified parts are obtained via a single-step process such as powder bed fusion, directed energy deposition, and sheet lamination AM technologies. Conversely, green bodies are consolidated with the aid of binder phases in multi-step processes such as binder jetting and material extrusion AM. Green-body part shapes are sustained by binder phases, which are removed for the debinding process. Chemical and/or thermal debinding processes are usually devised to enhance debinding kinetics. The pathways to final densification of the green parts are sintering and/or molten metal infiltration. With respect to innovation types, the multi-step metal AM process allows conventional powder metallurgy manufacturing to be innovated continuously. Eliminating cost/time-consuming molds, enlarged 3D design freedom, and wide material selectivity create opportunities for the industrial adoption of multi-step AM technologies. In addition, knowledge of powders and powder metallurgy fuel advances of multi-step AM technologies. In the present study, multi-step AM technologies are briefly introduced from the viewpoint of the entire manufacturing lifecycle.

• Journal of the Korean Society of Combustion
• /
• v.19 no.3
• /
• pp.18-25
• /
• 2014

Bottom ash from a coal-fired power plant is usually landfilled to a nearby site, which causes a growing environmental concern and increased operating costs. One way of recycling the bottom ash is to produce light-weight aggregate (LWA) using a rotary kiln. This study investigated the temperature profiles of raw LWA particles in a rotary kiln to identify the range of operating conditions appropriate for ideal bloating. For this purpose, a new simulation method was developed to integrate a 1-dimensional model for the bed of LWA particles and the computational fluid dynamics (CFD) for the fuel combustion and gas flow. The temperature of LWA particles was found very sensitive to the changes in the air preheating temperature and excess air ratio. Therefore, an accurate control of the operation parameters was essential to achieve the bloating of LWA particles without excessive sintering or melting.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.5
• /
• pp.117-122
• /
• 2018

3D printing technology and its applications have grown rapidly in academia and industry. We consider a 3D printing system designed for the selective laser sintering (SLS) method, which is one of the powder bed fusion (PBF) techniques to build up the final product by layering sintered powder slices. Thermal distortion of printing products is a critical challenge in 3D printing. This study investigates temperature-dependent conformational behaviors of 3D printed samples of sintered poly-ether-ether-ketone (PEEK) powders using molecular dynamics simulations. The wear and chemical resistance properties of PEEK are understood, as it is a well-known biocompatible material used for implants. However, studies on physical phenomena at nanoscale in PEEK are rarely published in public. We simulate dissipative particle dynamics to elucidate how a cavity regime forms in PEEK at different system temperatures. We demonstrate how PEEK structures deform subject to the system temperature distribution.

• Clean Technology
• /
• v.20 no.3
• /
• pp.212-217
• /
• 2014

In order to regenerate the sulfidated desulfurization sorbent, oxygen is used as the oxidant agent on the regeneration process. The small amount of oxygen un-reacted in regeneration process is flowed into direct sulfur recovery process. However, the reactivity for $SO_2$ reduction can be deteriorated with the un-reacted oxygen by various reasons. In this study, the deactivation effects of un-reacted oxygen contained in the off-gas of regeneration process flowed into direct sulfur recovery process of hot gas desulfurization system were investigated. Sn-Zr based catalysts were used as the catalyst for $SO_2$ reduction. The contents of $SO_2$ and $O_2$ contained in the regenerator off-gas used as the reactants were fixed to 5.0 vol% and 4.0 vol%, respectively. The catalytic activity tests with a Sn-Zr based catalyst were for $SO_2$ reduction performed at $300-450^{\circ}C$ and 1-20 atm. The un-reacted oxygen oxidized the elemental sulfur produced by $SO_2$ catalytic reduction and the conversion of $SO_2$ was reduced due to the production of $SO_2$. However, the temperature for the oxidation of elemental sulfur increased with increasing pressure in the catalytic reactor. Therefore, it was concluded that the decrease of reactivity at high pressure is occurred by catalytic deactivation, which is the re-oxidation of lattice oxygen vacancy in Sn-Zr based catalyst with the un-reacted oxygen on the catalysis by redox mechanism. Meanwhile the un-reacted oxygen oxidized CO supplied as the reducing agent and the temperature in the catalyst packed bed also increased due to the combustion of CO. It was concluded that the rapidly increasing temperature in the packed bed can induce the catalytic deactivation such as the sintering of active components.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.37 no.1
• /
• pp.1-15
• /
• 2021

Additive manufacturing (AM) for dental materials can produce more complex forms than conventional manufacturing methods. Compared to milling processing, AM consumes less equipment and materials, making sustainability an advantage. AM can be categorized into 7 types. Polymers made by vat polymerization are the most suitable material for AM due to superior mechanical properties and internal fit compared to conventional self-polymerizing methods. However, polymers are mainly used as provisional restoration due to their relatively low mechanical strength. Metal AM uses powder bed fusion methods and has higher fracture toughness and density than castings, but has higher residual stress, which requires research on post-processing methods to remove them. AM for ceramic use vat polymerization of materials mixed with ceramic powder and resin polymer. The ceramic materials for AM needs complex post-processing such as debinding of polymer and sintering. The low mechanical strength and volumetric accuracy of the products made by AM must be improved to be commercialized. AM requires more research to find the most suitable fabrication process conditions, as the mechanical properties and surface of any material will vary depending on the processing condition.

• Journal of Korean Society for Atmospheric Environment
• /
• v.23 no.1
• /
• pp.64-73
• /
• 2007

The catalytic activity of transition metals (Cu, Co, Mn, Fe and Ni) supported on ${\gamma}-Al_2O_3$ for the oxidation of toluene was investigated in the microreactor of fixed-bed type. The catalytic activity of transition metals for the oxidation of toluene turned out to be increasing in the order of Ni$Cu/{\gamma}-Al_2O_3$ catalysts for the oxidation of toluene increased with the increasing loadings of copper, reached the maximum activity at 5% loadings of copper, and decreased with higher loadings of copper in the catalysts. The activity of $Cu/{\gamma}-Al_2O_3$ catalysts for the oxidation of toluene decreased with the increasing calcination temperatures. This might result from the decreasing surface area of catalysts due to the sintering of copper oxide as well as ${\gamma}-Al_2O_3$ supports. The 5wt% $Cu/{\gamma}-Al_2O_3$ catalysts calcined at $400^{\circ}C$ for 4 hrs in the air showed the highest activity for the oxidation of toluene. Mutual inhibition was observed for the binary mixture of toluene and xylene. The activity of the easy-to-oxidize toluene was greatly decreased while the difficult-to-oxidize xylene was slightly decreased in the binary mixture of toluene and xylene. It might suggest that the inhibition of toluene and xylene in the binary mixture resulted from the competitive adsorption for the adsorbed oxygen on the catalytic surface.

• Journal of Biomedical Engineering Research
• /
• v.43 no.2
• /
• pp.116-123
• /
• 2022

This study analyzes the Mechanical properties of a medical bone plate by 3D printing. With the recent development of 3D printing technology, it is being applied in various fields. In particular, in the medical field, the use of 3D printing technology, which was limited to the existing orthosis and surgical simulation, has recently been used to replacement bones lost due to orthopedic implants using metal 3D printing. The field of application is increasing, such as replacement. However, due to the manufacturing characteristics of 3D printing, micro pores are generated inside the metal printing output, and it is necessary to reduce the pores and the loss of mechanical properties through post-processing such as heat treatment. Accordingly, the purpose of this study is to analyze the change in mechanical performance characteristics of medical metal plates manufactured by metal 3D printing under various conditions and to find efficient metal printing results. The specimen to be used in the experiment is a metal plate for trauma fixation applied to the human phalanx, and it was manufactured using the 'DMP Flex 100(3D Systems, USA), a metal 3D printer of DMLS (Direct Metal Laser Sintering) method. It was manufactured using the PBF(Powder Bed Fusion) method using Ti6Al4V ELI powder material.

• Journal of Institute of Convergence Technology
• /
• v.6 no.2
• /
• pp.35-40
• /
• 2016

Ignitor tip is a component of burner to start the burning process in power plant. This is used to ignite the coal to a constant operating state by fuel mixed with air and kerosene. This component is composed of three components so that air and kerosene are mixed in the proper ratio and injected uniformly. Because the parts with the designed shape are manufactured in the machining process, they have to be made of three parts. These parts are designed to have various functions in each part. The mixing part mixes the supplied air and kerosene through the six holes and sends it to the injecting part at the proper ratio. The inject part injects mixed fuel, which is led to have a constant rotational direction in the connecting part, to the burner. And the connecting plate that the mixed fuel could rotate and spray is assembled so that the flame can be injected uniformly. But this part causes problems that are worn by vibration and rotation because it is mechanically assembled between the mixing part and the inject part. In this study, 3D printing method is used to integrate a connecting plate and an inject part to solve this wear problem. The 3D printing method could make this integrated part because the process is carried out layer by layer using a metal powder material. The part manufactured by 3D printing process should perform the post process such as support removal and surface treatment. However, while performing the 3D printing process, the material properties of the metal powders are changed by the laser sintering process. This change in material properties makes the post process difficult. In consideration of these variables, we have studied the optimization of manufacturing process using 3D printing method.

• Journal of Korean Society for Atmospheric Environment
• /
• v.22 no.6
• /
• pp.799-807
• /
• 2006

The catalytic activity of $Pt/{\gamma}-Al_2O_3$ catalysts for the oxidation of toluene and toluene+xylene mixture was investigated in the microreactor of fixed-bed type. The calcination temperatures and loadings of $Pt/{\gamma}-Al_2O_3$ catalysts played the important role in the activity of catalysts for the oxidation of toluene. The increasing calcination temperatures and loadings of $Pt/{\gamma}-Al_2O_3$ catalysts increased the crystallite size of the platinum to result in the higher oxidation activity of catalysts. The catalytic activity for the toluene oxidation over $Pt/{\gamma}-Al_2O_3$ catalysts turned out to be increasing in the order of $500^{\circ}C\;<\;800^{\circ}C<600^{\circ}C\;<\;700^{\circ}C$ for calcination temperatures and 0.1 wt% < 0.3 wt% < 1.0 wt% for platinum loadings, respectively. The 1.0 wt% $Pt/{\gamma}-Al_2O_3$ catalysts calcined at $700^{\circ}C$ for 3 hrs in the air showed the highest activity for the oxidation of the toluene. The decrease of oxidation activity of $Pt/{\gamma}-Al_2O_3$ catalysts calcined at $800^{\circ}C$ might result from the decrease of active sites by sintering of platinum metals as well as ${\gamma}-Al_2O_3$ supports. The 1.0wt% $Pt/{\gamma}-Al_2O_3$ catalyst showed the activity from the lower temperature at $120^{\circ}C$, reached the light-off temperature ($T_{50%}$) at $180^{\circ}C$, and leveled off its activity at $340^{\circ}C$ with the conversion of 100% 'Mutual promotion' effects were observed for the binary mixture of toluene and xylene. The activity of the easy-to-oxidize toluene was slightly increased with the existence of the xylene. It might suggest the different mechanism for the oxidation of toluene and xylene on the $Pt/{\gamma}-Al_2O_3$ catalysts on different sites, and its reaction of gaseous oxygen.