• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.8
• /
• pp.36-41
• /
• 2013

This paper is development of single-phase brushless DC motor with outer rotor for ventilation fan. Cogging torque causes the noise vibration to greatest impact on ventilation fan. Asymmetric notches are applied to tapered-teeth for cogging torque reduction of single-phase brushless DC motor. Initial model is notchless and proposed model is applied 2 asymmetric notches. The proposed method is proved motor characteristic through finite element analysis(FEA). Also, experimental results verify that the proposed model considerably reduces cogging torque and have the good sound quality in ventilation system.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.12
• /
• pp.592-600
• /
• 2001

This Paper presents the transient analysis of the single-phase line-start permanent magnet synchronous motor. To analyse the starting characteristics, the dynamic equation which is combined electric dynamic equations with mechanical dynamic equation is used. The electric dynamics are derived from the d-q axis voltages of stator and rotor respectively. Especially, symmetrical components transformation is used to consider unbalanced magnetic field which is produced by single-phase input. Non-linear d-q axis inductances according to current amplitude and current phase angle are calculated by Finite Element Method and applied to lumped parameter circuit. The analysis methods are validated by comparing simulated and experimental results.

• Proceedings of the KIEE Conference
• /
• 2005.10c
• /
• pp.89-91
• /
• 2005

In This paper the convertor topology using single diode bridge rectifier for the now two-phase switched reluctance motor is proposed. The single diode bridge rectifier is supplied by the Ac voltage source. The nonlinear model of two-phase SRM is implement by maxwell and result show the photographic.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.5
• /
• pp.238-245
• /
• 2001

During an AC motor's start-up accelerating period, a large amount of current is required to reach to the rating speed. This is called in-rush current. This peak in-rush current can be more than about several times the operating or steady-state current in the full load rating of the motor. In-rush current is present in both and electronic ballasts. The main area of concern is the tripping of circuit breaker and fuses which can affect electrical system components From this, we can see that the electrical power controllers will be rather concerned, since they have to supply the actual current necessary to start the motor. This paper presents a new method to reducing in-rush current and energy saving of the single-phase induction motor used in air-conditioner. It can be obtained that proposed system is low cost and small size as compared with other controller. Experiments are focused on a capacitor starting single-phase induction motor. The optimal power saving and in-rush current limiting by phase angle control are verified by experimental results. Also, auxiliary winding was controlled by electronic starting switch.

• 전기의세계
• /
• v.22 no.1
• /
• pp.42-51
• /
• 1973

The contriving equivalent circuit of single phase induction motor which does not separate the primary leakage reactance and the secondary leakage reactance by the revolving field theory, and the graphically calculating method of the characteristics with T-type circle diagram of three phase induction motor which does not suppose the primary leakage reactance can be drawn up only by the no load test, the lock test, and measuring the resistance of stator winding are suggested in this paper. The method which can calculate the parameters of the equivalent circuit and the characteristics with no load test, lock test and measuring resistance of stator windings is suggested in this paper. Considered the exciting current in lock test, we could calculate very accurate characteristics of the single phase induction motor.

• Fire Science and Engineering
• /
• v.34 no.2
• /
• pp.64-71
• /
• 2020

In this paper, the fire risk of a single-phase induction motor under a locked-rotor condition is described. In general, motor failure occurs in the locked-rotor condition owing to poor rotation of the rotor. Large inrush current flows when a motor starts, which is approximately 2-15 times larger than the rated current. In a single-phase induction motor under the locked-rotor condition, a large current that corresponds to the inrush current flows continuously through the stator winding. Such an overcurrent rises the temperature inside the stator winding, and thus the insulating material may catch fire. In this study, the restrained operating condition of the single-phase induction motor was simulated. Further, the degree of the overcurrent and temperature rise in the stator winding was measured. The experimental results, confirmed that the overcurrent was seven times larger than the rated current and the fire commenced at a temperature of approximately 300 ℃ inside the stator winding.

• Proceedings of the KIEE Conference
• /
• 2006.04b
• /
• pp.203-205
• /
• 2006

This paper presents a study on the winding method and structure of core of single phase induction motor in order to design the high efficiency motor. In case of single phase induction motor, winding fill factor and the number of turns in each slot are not uniform in general. Moreover, these can be the critical parameters for high efficiency design in case the size of motor should be restricted within certain volume. Therefore, we should analyze the effects of these parameters related to efficiency parameter. The characteristic analysis was performed by using FEM.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.846-847
• /
• 2011

This paper presents the study on analysis of single phase induction motor characteristics by equivalent circuit. For high efficiency of single phase induction motor, the motor parameters used for equivalent circuit analysis is important. The accuracy of equivalent circuit analysis of motor depends on the circuit parameters like saturation factor. Therefore this paper proposed the analysis method considering saturation factor. The saturation factor was calculated by iteration routine and numerical method. this proposed method was verified by FEM analysis results and dynamo test results of the prototype model.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.12
• /
• pp.596-607
• /
• 2006

This paper presents Single Phase Switched Reluctance Motor (SPSRM) optimum design for vacuum cleaners using Response Surface Methodology (RSM) to determine geometric parameters, and the 2-D Finite Element Method (FEM) has been coupled with the circuit equations of the driving converter. Additionally, an optimum process for SPSRM has been proposed and peformed with geometric and electric parameters thereby influencing the inductance variation and effective torque generation as design variables. SPSRM performances have also been analyzed to determine an optimal design model for maximized efficiency at high power factor. In order to confirm the propriety of the Finite Element Method and motor performance calculation, simulation waveform and experiment waveform for motor voltage and current were compared.

• Journal of the Korean Society of Industry Convergence
• /
• v.17 no.3
• /
• pp.113-121
• /
• 2014

This paper presents a optimization design of 10[W] single phase BLDC motor applied Notch shape. Cogging Torque causes noise, vibration and torque ripple so notched stator is proposed in this paper. Firstly, a single phase BLDC motor needs applying aymmetric air-gap shape because this type motor cannot help having dead-point which is zero torque position. However, using asymmetric air-gap structure causes cogging torque increase. Therefore, this paper proposes the notch shape structure. Notch shape structure has some advantages; low cost, easy to apply. There are 4 optimal factors selected in optimization process, which are position and size of notches. Through building a prototype, the result of FE analysis and the experimental measurement value are compared each other and then vailidity and utility of simulation will be verified.