• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.5
• /
• pp.455-462
• /
• 2015

H-field EMI measurements have been performed for the single-ended, the differential, and the pseudo-differential signaling on a 11" FR4 microstrip line. The pseudo-differential signaling reduces EMI by more than 10 dB compared to the single-ended signaling if the delay mismatch is lower than 5% of a period for a 3 GHz clock signal. Empirical H-field equations for both differential and single-ended signaling showed fair agreements with measurements.

• Journal of IKEEE
• /
• v.23 no.3
• /
• pp.1046-1053
• /
• 2019

In a multi-channel single-ended system, the far-end crosstalk (FEXT) due to mutual inductance and mutual capacitance between two adjacent channels critically limit the bandwidth. FEXT causes crosstalk-induced jitter (CIJ) and crosstalk-induced glitch (CIG) which leads to timing margin and voltage margin degradations, respectively. Therefore, FEXT must be compensated in order to increase eye opening and achieve high data-rate. It can be compensated in transmitter by controlling the timing of the data or reshaping the waveform of the signal. Also, FEXT can be compensated in receiver by generating mimicked FEXT using high-pass filter. In this paper, recent techniques to compensate FEXT are investigated, with discussions of their pros and cons.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.6
• /
• pp.817-824
• /
• 2016

A simultaneous bidirectional transceiver over a single wire has been developed in a 65 nm CMOS technology for a command and control bus. The echo signals of the simultaneous bidirectional link are cancelled by controlling the decision level of receiver comparators without power-hungry operational amplifier (op-amp) based circuits. With the clock information embedded in the rising edges of the signals sent from the source side to the sink side, the data is recovered by an open-loop digital circuit with 20 times blind oversampling. The data rate of the simultaneous bidirectional transceiver in each direction is 75 Mbps and therefore the overall signaling bandwidth is 150 Mbps. The measured energy efficiency of the transceiver is 56.7 pJ/b and the bit-error-rate (BER) is less than $10^{-12}$ with $2^7-1$ pseudo-random binary sequence (PRBS) pattern for both signaling directions.

• Journal of IKEEE
• /
• v.20 no.3
• /
• pp.285-290
• /
• 2016

Inter-symbol interference (ISI) due to channel bandwidth limitation constrains the maximum data rate in high speed I/O. Decision feedback equalizer (DFE) is known as the most popular technique for removing ISI. To ensure fast data transmission, not only removing ISI but also raising maximum operating frequency of the circuit itself by relaxing feedback delay margin is important. For single-ended signaling, DFE should cancel out both ISI and high frequency noises. Low-power operation is as important as fast operation because required DFE elements increase as the data rate goes up. This paper surveys recent techniques for fast DFE by removing ISI and high frequency noises, and low power DFE and discusses about their merits and limitations.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.05a
• /
• pp.490-492
• /
• 2010

A swing level controlled voltage-mode transmitter is proposed to support a stub series-terminated logic channel with center-tapped termination. This transmitter provides a swing level control to support the diagnostic mode and improve the signal integrity in the absence of the destination termination. By using the variable parallel termination, the proposed transmitter maintains the constant output impedance of the source termination while the swing level is controlled. Also, the series termination using an external resistor is used to reduce the impedance mismatch effect due to the parasitic components of the capacitor and inductor. To verify the proposed transmitter, the voltage-mode driver, which provides eight swing levels with the constant output impedance of about $50{\Omega}$, was implemented using a 70nm 1-poly 3-metal DRAM process with a 1.5V supply. The jitter reduction of 54% was measured with the swing level controlled voltage-mode driver in the absence of the destination termination at 1.6-Gb/s.

• Journal of Power Electronics
• /
• v.9 no.4
• /
• pp.604-611
• /
• 2009

A dP/dV feedback-controlled MPPT (Maximum Power Point Tracking) method for photovoltaic power systems using II-SEPIC (Isolated Inverse-SEPIC; Single Ended Primary Inductance Converter) is presented and a current-mode dP/dV feedback-controlled MPPT method is devised to apply for the PV power converter system. A control strategy for the current-mode dP/dV feedback control system is developed in this paper and the proposed MPPT shows relatively satisfactory dynamics against rapidly changing insolation conditions. In order to verify the validity and effectiveness of the proposed method, simulations and experiments of the PV power system using II-SEPlC converter are performed. These simulation and experiment results show that the proposed method enables the PV power system to extract maximum power from the photovoltaic module against the solar insolation variation.