• International Journal of Aerospace System Engineering
• /
• v.2 no.2
• /
• pp.29-33
• /
• 2015

The multidisciplinary design optimization (MDO) of a launch vehicle (LV) with a hybrid rocket engine (HRE) was carried out to investigate the ability of an HRE for a single-stage LV. The non-dominated sorting genetic algorithm-II (NSGA-II) was employed to solve two design problems. The design problems were formulated as two-objective cases involving maximization of the downrange distance over the target flight altitude and minimization of the gross weight, for two target altitudes: 50.0 km and 100.0 km. Each objective function was empirically estimated. Several non-dominated solutions were obtained using the NSGA-II for each design problem, and in each case, a trade-off was observed between the two objective functions. The results for the two design problem indicate that economical performance of the LV is limited with the HRE in terms of the maximum downrange distances achievable. The LV geometries determined from the non-dominated solutions were examined.

• Structural Engineering and Mechanics
• /
• v.6 no.1
• /
• pp.77-93
• /
• 1998

Some design formulas and design procedures for single and multiple tuned liquid column dampers (TLCDs) are proposed in this study. Previous studies show that if the properties of the TLCD system are properly selected then the TLCD could be as effective as the traditional tuned mass dampers. In addition, the TLCD system offers advantages such as flexibility in terms of installation, little maintenance required, and potentials for multiple usage, etc., which are incomparable by other mechanical types of dampers. In this paper, a set of optimal properties such as length and head loss of a TLCD system are derived under the assumption that the building vibrates in a dominate mode and is subjected to Gaussian white noise excitation. A design procedure for a single TLCD system will be illustrated and discussed. Due to the nonlinearity in the damping term, the TLCD system is sensitive to the loading intensity. This loading sensitivity could limit the application range of the TLCD system. It will be shown in this paper that such a nonlinear effect can be reduced by using multiple TLCDs. As a demonstrative example, the control effects on a flexible building modeled as a single degree-of-freedom system subjected to white noise excitation will be analyzed and discussed using single or multiple TLCDs.

• Journal of the Optical Society of Korea
• /
• v.19 no.4
• /
• pp.421-426
• /
• 2015

This paper presents a hybrid single optical system for an LED surgical light that combines the advantages of both lens- and reflector-type single optical systems. The proposed hybrid single optical system includes a lens in the center and the LED light originating from the lens is redirected using a reflector to achieve a high beam spread. Iterative optical software simulations are used to provide data for the design of the lens and reflector for a single optical system, and for a complex optical system for the LED light assembly. The resulting data is also used to fabricate a prototype system. Experiments using the prototype of the hybrid single optical system and a mock-up LED surgical light confirm the system's shadow dilution performance and its applicability to surgical operations.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.2
• /
• pp.94-100
• /
• 2018

Generally, in a single-phase energy storage system (ESS) for households, AC ripple component with twice the fundamental frequency exists inevitably in the DC link voltage of single-phase PCS. In the grid-connected mode of a single-phase inverter, the AC ripple component in the DC link voltage causes low-order harmonics on grid-side current that deteriorates power quality on an AC grid. In this work, a control system adopting a feedforward controller is established to eliminate the AC ripple interference on the DC link side. Optimal battery nominal voltage design method is also proposed by considering the voltage loss and AC ripple voltage on DC link side in a single-phase ESS. Finally, the control system and battery nominal voltage design method are verified through simulations and experiments.

• International Journal of Fluid Machinery and Systems
• /
• v.9 no.4
• /
• pp.370-381
• /
• 2016

As a single-channel pump is used for wastewater treatment, this particular pump type can prevent performance reduction or damage caused by foreign substances. However, the design methods for single-channel pumps are different and more difficult than those for general pumps. In this study, a design optimization method to improve the hydrodynamic performance of a single-channel pump impeller is implemented. Numerical analysis was carried out by solving three-dimensional steady-state incompressible Reynolds-averaged Navier-Stokes equations using the shear stress transport turbulence model. As a state-of-the-art impeller design method, two design variables related to controlling the internal cross-sectional flow area of a single-channel pump impeller were selected for optimization. Efficiency was used as the objective function and was numerically assessed at twelve design points selected by Latin hypercube sampling in the design space. An optimization process based on a radial basis neural network model was conducted systematically, and the performance of the optimum model was finally evaluated through an experimental test. Consequently, the optimum model showed improved performance compared with the base model, and the unstable flow components previously observed in the base model were suppressed remarkably well.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.11B no.3
• /
• pp.104-111
• /
• 2001

The design procedures and experimental results of a single-stage electronic ballast using half-bridge resonant inverter are presented in this paper. The proposed topology is based on a single-stage ballast which combines a boost converter and a half-bradge series resonant inverter. High power factor is achieved by using the boost semi-stage operating in discontinuous conduction mode and inverter semi-stage operated above resonant frequency to provide zero voltage switching is empolyed to ballast the fluorescent lamp Experimental results from the ballast system with 36W fluorescent

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.5
• /
• pp.445-452
• /
• 1990

In order to design a conveyer system which is driven by short primary single sided linear induction motors (SLIM), the thrust force characteristics of SLIM have been calculated from the fundamental equation based on Maxwell's electromagnetic equation and by varying the various design parameters. A conveyer system of moving secondary has been constructed using the design values obtained by the simulation and these values are compared with the experimental values. The control method of the conveyer system is also proposed.

• Nuclear Engineering and Technology
• /
• v.55 no.3
• /
• pp.1015-1020
• /
• 2023

A multi-layer design is applied to mitigate single event effect (SEE) in a 28 nm System-on-Chip (SoC). It depends on asymmetric multiprocessing (AMP), redundancy and system watchdog. Irradiation tests utilized 70 and 90 MeV proton beams to examine its performance through comparative analysis. Via examining SEEs in on-chip memory (OCM), compared with the trial without applying the multi-layer design, the test results demonstrate that the adopted multi-layer design can effectively mitigate SEEs in the SoC.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.251-254
• /
• 2011

This paper describes the design and implementation of the DMI display based on ERTMS specification for the Integrated Onboard Signaling System (IOSS). IOSS is consists of ATS, ATC, and ATP based on ERTMS/ETCS Level 1. We propose an improved DMI display design which has single layout concept for the IOSS. When a train is in the ATS, ATC, or ATP railway section, it is protected by the ATS, ATC, or ATP equipment, respectively. Therefore, DMI should display the different information according to the each signaling system. We design DMI display implemented as single layout for ATP, ATS and ATC information. This single layout display has a well integrated look and feel using the ERTMS specification and layout. This is for the driver to perceive the information easily and not to experience inconvenience resulting from the sense of difference when the train crossed into the different signaling section. Finally, we show the implementation result following this concept.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.213-217
• /
• 1999

An expert system is developed for rational and efficient design of multi-component injection molding which is a fairly new manufacturing technique to produce plastic parts by injecting two or more materials sequentially using multiple injection units in a single machine into a single rotary mold. The knowledge base used in the present design system is primarily composed of two parts ; knowledge from domain expert and knowledge from CAE analysis. The present expert system has hour main modules ; general design guidelines for injection molding specific guidelines for multi-component injection molding redesign guidelines from the result of the CAE analysis and finally troubleshooting for multi-component injection molding. To show the validity of the present design methodology two shop floor design problems were tested ; design and fabrication of timing belt cover and power window's assist knob by using multi-component injection molding.