• Steel and Composite Structures
• /
• 제44권5호
• /
• pp.741-752
• /
• 2022

Earlier works have shown that excessive shear stiffness at the steel-concrete interface causes a non-uniform distribution of shear force in composite structures. When the shear studs are wrapped at the fixed end with flexible materials with a low elastic modulus, the shear stiffness at the interface is reduced. The objective of this study was to investigate the effect of silicone rubber-sleeve mounted on shear studs on the shear stiffness of steel-concrete composite structures. Eighteen push-out tests were conducted to investigate the mechanical behavior of silicone rubber-sleeved shear stud groups (SRS-SSG). The dimension and arrangement of silicon rubber-sleeves (SRS) were taken into consideration. Test results showed that the shear strength of SRS-SSG was higher than that of a shear stud group (SSG), without SRS. For SRS-SSG with SRS heights of 50 mm, 100 mm, 150 mm, the shear strengths were improved by 13%, 20% and 9%, respectively, compared to the SSG alone. The shear strengths of SRS-SSG with the SRS thickness of 2 mm and 4 mm were almost the same. The shear stiffness of the SRS-SSG specimens with SRS heights of 50 mm, 100 mm and 150 mm were 77%, 67% and 66% of the SSG specimens, respectively. Test results of specimens SSG-1 and predicted values based on the three design specifications were compared. The nominal single stud shear strength of SSG-1 specimens was closest to that calculated by the Chinese Code for Design of Steel Structures (GB50017-2017). An equation is proposed to consider the effects of SRS for GB50017-2017, and the predicted values based on the proposed equation agree well with the tested results of SRS-SSG.

• 대한조선학회지
• /
• 제3권1호
• /
• pp.19-24
• /
• 1966

The maximum shear stress distribution in a stiffening flat attached to a plat undergoing a single tensile force has been investigated by photoelastic method. In the experiments a photoelastic model, as shown in Fig. 1, has been studied in the fields of a polariscope, as shown in Fig. 2. Fig. 3 shows the isoclinics and Fig. 4 and 5 are stress trajectories of the principal stresses and maximum shear stresses, respectively. Fig. 6 is the isochromatics in light field. The maximum shear stress at each point in the stiffener were determined from the isochromatics in both of light field of light field and dark field. Then the maximum shear stresses were divided by the average shear stress in the model, to obtain the ratio ${\tau}max/{\tau}av$ at each point. Finaly the variations of the ratio ${\tau}max/{\tau}av$ along the horizontal and vertical lines in the stiffener have been plotted, as shown in Fig. 7 and 8. The conclusions reached in this investigation are as follows: (1) The shear stresses transmitted to the stiffener through the juncture are concentrated on the end portions. (2) The maximum shear stress at the ends of the stiffener reaches to about 4 times of average shear stress. (3) The irregularities in the stress distribution are restricted in the end portions of the stiffener.

• 대한토목학회논문집
• /
• 제36권6호
• /
• pp.1049-1057
• /
• 2016

파형 마이크로파일은 제트 그라우팅 공법을 활용하여 마이크로파일의 그라우트체를 단일 또는 복수개의 전단키를 갖는 파형의 형상으로 시공하는 기초 형식으로, 전단키와 지반 접촉면에서의 주면마찰력을 증가시켜 기존 마이크로파일의 지지성능을 개선하고자 개발되었다. 본 논문에서는 파형 마이크로파일의 전단키의 위치에 따른 형상별 거동 특성을 검토하기 위하여 전단키가 말뚝의 상부, 중앙, 하부 및 다층에 적용된 파형 마이크로파일과 일반 마이크로파일, 제트 그라우팅 마이크로파일에 대한 원심모형실험을 수행하였다. 실험결과, 각 말뚝의 하중-침하 관계로부터 전단키가 없는 마이크로파일에 비해 파형 마이크로파일의 뚜렷한 지지력 증대 효과를 확인하였으며, 또한 전단키가 큰 구속압을 갖는 지반의 하부 및 단단한 지층에 시공될 경우 지지력 증대에 유리한 것으로 나타났다.

• Structural Engineering and Mechanics
• /
• 제48권4호
• /
• pp.519-545
• /
• 2013

An outline of the Timoshenko beam theory is presented. Two differential equations of motion in terms of deflection and rotation are comprised into single equation with deflection and analytical solutions of natural vibrations for different boundary conditions are given. Double frequency phenomenon for simply supported beam is investigated. The Timoshenko beam theory is modified by decomposition of total deflection into pure bending deflection and shear deflection, and total rotation into bending rotation and axial shear angle. The governing equations are condensed into two independent equations of motion, one for flexural and another for axial shear vibrations. Flexural vibrations of a simply supported, clamped and free beam are analysed by both theories and the same natural frequencies are obtained. That fact is proved in an analytical way. Axial shear vibrations are analogous to stretching vibrations on an axial elastic support, resulting in an additional response spectrum, as a novelty. Relationship between parameters in beam response functions of all type of vibrations is analysed.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2007년 가을학술발표회
• /
• pp.127-137
• /
• 2007

Faults are fractures along which there is visible offset by shear displacement parallel to the fracture surface. Faults can occur as single discrete breaks, but where the rock has been repeatedly faulted, or where the rock is especially weak, no discrete break may be evident. What forms instead is a fault zone composed of countless subparallel and interconnecting closely spaced fault surfaces. Faulting is fundamentally a brittle mechanism for achieving shear displacement. At deep crustal levels where rocks tend to deform plastically under conditions of elevated temperature and confining pressure, shear displacement is achieved by and development of shear zones. In this paper authors propose the fault grade in Korea.

• Journal of Mechanical Science and Technology
• /
• 제16권2호
• /
• pp.255-261
• /
• 2002

A newly designed mass-detecting capillary viscometer uses a novel concept to continuously measure non-Newtonian fluids viscosity over a range of shear rates. A single measurement of liquid-mass variation with time replaces the now rate and pressure drop measurements that are usually required by capillary tube viscometers. Using a load cell and a capillary, we measured change in the mass flow rate through a capillary tube with respect to the time, m(t), from which viscosity and shear rate were mathematically calculated. For aqueous polymer solutions, excellent agreement was found between the results from the mass-detecting capillary viscometer and those from a commercially available rotating viscometer. This new method overcomes the drawbacks of conventional capillary viscometers meassuring non-Newtonian fluid viscosity. First, the mass-detecting capillary viscometer can accurately and consistently measure non -Newtonian viscosity over a wide range of shear rate extending as low as 1 s$\^$-1/. Second, this design provides simplicity (i. e., ease of operation, no moving parts), and low cost.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.987-992
• /
• 1997

Burrs always come out with the machining of ducterial with small size. Though the size of burrs is small, burrs dominate deterioration of the accuracy of the micro grooves. So the burr generation model especially side burr generation model was investigated to predict the size of the burrs at the given cutting conditions. The side shear plane is introduced to build the burr generation model and the width of side shear plane nomalized with cutting depth is defined with the shear angle. From the theoretical observation, the width of side shear plane can vary up 40% of the cutting depth. To determine the size of burr and stiffness, single groovings were carried out and it was found that there exist a critical depth of cut that the size or stiffness of the burr vary.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 봄 학술발표회 논문집
• /
• pp.512-517
• /
• 2003

The repeated loading responses of four shear-critical reinforced concrete beams, with two different shear span-to-depth ratios, were studied. One series of beams was reinforced using pairs of bundled stirrups with $90^{\circ}C$ standard hooks, having free end extensions of $6d_b$. The companion beams contained shear reinforcement made with larger diameter headed bars anchored with 50mm diameter circular heads. A single headed bar had the same area as a pair of bundled stirrups and hence the two series were comparable. The test results indicate that beams containing headed bar stirrups have a superior performance to companion beams containing bundled standard stirrups, with improved ductility, larger energy adsorption and enhanced post-peak load carrying capability. Due to splitting of the concrete cover and local crushing, the hooks of the standard stirrups opened, resulting in loss of anchorage. In contrast, the headed bar stirrups did not lose their anchorage and hence were able to develop strain hardening and also served to delay buckling of the flexural compression steel. Excellent load-deflection predictions were obtained by reducing the tension stiffening to account for repeated load effects.

• Structural Engineering and Mechanics
• /
• 제67권3호
• /
• pp.291-300
• /
• 2018

In this work, a new trigonometry theory of shear deformation is developed for the static analysis of thick isotropic beams. The number of variables used in this theory is identical to that required in the theory of Euler-Bernoulli, sine function is used in the displacement field in terms of the coordinates of the thickness to represent the effects of shear deformation. The advantage of this theory is that shear stresses can be obtained directly from the relationships constitute, while respecting the boundary conditions at the free surface level of the beam. Therefore, this theory avoids the use of shear correction coefficients. The differential equilibrium equations are obtained using the principle of virtual works. A thick isotropic beam is considered, whose numerical study to show the effectiveness of this theory.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2001년도 봄 학술발표회 논문집
• /
• pp.317-322
• /
• 2001

A mathematical modelling technique is proposed for estimating the additional bending stresses of tube(s)-in-tube structures due to tube-tube interaction, which has a significant effects on the shear-lag phenomenon. The proposed method simulates the framed-tube structures with multiple internal tubes as equivalent multiple tubes, each composed of four equivalent orthotropic plate panels. Hence, the tube(s)-in-tube structure can be analysed by using an analogy approach where each tube is individually modelled by a continuous beam that can account for the flexural and shear deformations as well as the shear-lag effects. The numerical analysis is applicable for the structural analysis of framed-tube structures with single and multiple internal tubes, as well as those without internal tubes. The shear-lag phenomenon of such structures is studied with additiona] bending stresses and shear-lag reversal points.