• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.5
• /
• pp.76-84
• /
• 2007

In this paper, we measured the propagation characteristics of I-UWB channel in time domain and in frequency domain. The measurements carried out in apartment environment while furniture and household electric appliance. Typical indoor scenarios, including line-of-sight(LOS), non-line-of-sight(NLOS) in room-to-room, within-the-room. A transmitting and receiving antenna is a biconical antenna. Results for indoor propagation measurements are presented for power delay profiles(PDP). We extracted the channel characteristic parameters from a power delay profile. Finally, we designed I-UWB channel model in indoor environment, and I-UWB simulator. The results of simulation shows BER characteristics below $10^{-5}$ for SNR over 20[dB].

• Journal of the Korean Solar Energy Society
• /
• v.37 no.3
• /
• pp.47-59
• /
• 2017

As the global warming threats to humanity, renewable energy is considered the key solution to overcome the climate change. In this circumstance, distributed PV systems are being expanded significantly its market share in the renewable energy industry. The performance of inverter is the most important component at PV system and numerous researches are focusing on it. In order to improve the inverter, PV simulator is an essential device to experiment under various load and conditions. This paper proposes the PV Power-Hardware-In-Loop simulator (PHILS) with real-time processing converted electrical and mathematical models to improve computation speed. Single-diode PV model is used in MATLAB/SIMULINK for the PV PHILS to boosting computation speed and dynamic model accuracy. In addition, control algorithms for sub-components such as DC amplifier, measurement device and several interface functions are implemented in the model. The proposed PV PHILS is validated by means of experiments with commercial PV module parameters.

• Journal of Power Electronics
• /
• v.15 no.1
• /
• pp.190-201
• /
• 2015

This paper uses the switching function approach to present a simple state model of the Vienna-type rectifier. The approach introduces the relationship between the DC-link neutral point voltage and the AC side phase currents. A novel direct power control (DPC) strategy, which is based on the sliding mode control (SMC) for Vienna I rectifiers, is developed using the proposed power model in the stationary ${\alpha}-{\beta}$ reference frames. The SMC-based DPC methodology directly regulates instantaneous active and reactive powers without transforming to a synchronous rotating coordinate reference frame or a tracking phase angle of grid voltage. Moreover, the required rectifier control voltages are directly calculated by utilizing the non-linear SMC scheme. Theoretically, active and reactive power flows are controlled without ripple or cross coupling. Furthermore, the fixed-switching frequency is obtained by employing the simplified space vector modulation (SVM). SVM solves the complicated designing problem of the AC harmonic filter. The simplified SVM is based on the simplification of the space vector diagram of a three-level converter into that of a two-level converter. The dwelling time calculation and switching sequence selection are easily implemented like those in the conventional two-level rectifier. Replacing the current control loops with power control loops simplifies the system design and enhances the transient performance. The simulation models in MATLAB/Simulink and the digital signal processor-controlled 1.5 kW Vienna-type rectifier are used to verify the fast responses and robustness of the proposed control scheme.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05a
• /
• pp.21-25
• /
• 2002

Activated sludge processes are widely used in biological wastewater treatment processes. The main motivation of this research is to develop an intelligent control strategy for activated sludge process (ASP). ASP is a complex and nonlinear dynamic system because of the characteristic of wastewater, the change in influent rate, weather conditions, and so on. The mathematical model of ASP also includes uncertainties which are ignored or not considered by process engineer or controller designer. The ASP model based on Matlab/Simulink is designed in this paper. The performance of the model is tested by IWA (International Water Association) and COST (European Cooperation in the filed of Scientific and Technical Research) data that include steady-state results during 14 days. In this paper, fuzzy logic control approach is applied to control the DO (dissolved oxygen) concentration. The fuzzy logic controller that includes two inputs and one output can adjust air flowrate. Also, this paper introduces the remote monitoring and control system that is applied for the CSTR (Continuously Stirred Tank Reactor) wastewater treatment system. The CSTR plant has a local control and the remote monitoring system which is contained communication parts which consist of LAN (Local Area Network) network and CDMA (Code Division Multiple Access) wireless module. Remote control and monitoring systems are constructed in the laboratory.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.10
• /
• pp.1905-1919
• /
• 2000

The main motivation of this research is to develop an intelligent control strategy for Activated Sludge Process (ASP). ASP is a complex and nonlinear dynamic system because of the characteristic of wastewater, the change in influent flow rate, weather conditions, and etc. The mathematical model of ASP also includes uncertainties which are ignored or not considered by process engineer or controller designer. The ASP is generally controlled by a PID controller that consists of fixed proportional, integral, and derivative gain values. The PID gains are adjusted by the expert who has much experience in the ASP. The ASP model based on $Matlab^{(R)}5.3/Simulink^{(R)}3.0$ is developed in this paper. The performance of the model is tested by IWA(International Water Association) and COST(European Cooperation in the field of Scientific and Technical Research) data that include steady-state results during 14 days. The advantage of the developed model is that the user can easily modify or change the controller by the help of the graphical user interface. The ASP model as a typical nonlinear system can be used to simulate and test the proposed controller for an educational purpose. Various control methods are applied to the ASP model and the control results are compared to apply the proposed intelligent control strategy to a real ASP. Three control methods are designed and tested: conventional PID controller, fuzzy logic control approach to modify setpoints, and fuzzy-PID control method. The proposed setpoints changer based on the fuzzy logic shows a better performance and robustness under disturbances. The objective function can be defined and included in the proposed control strategy to improve the effluent water quality and to reduce the operating cost in a real ASP.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.4
• /
• pp.340-346
• /
• 2008

An unmanned surveillance robot consists of a machine gun, a laser receiver, a thermal imager, a color CCD camera, and a laser illuminator. It has two axis control systems for elevation and azimuth. Because the current robot system is mounded at a fixed post to take care of surveillance tasks, it is necessary to modify such a surveillance robot to be installed on an UGV (Unmanned Ground Vehicle) system in order to watch blind areas. Thus, it is required to have a stabilization system to compensate the disturbance from the UGV. In this paper, a simulation based design scheme has been adopted to develop a mobile surveillance robot. The 3D CAD geometry model has first been produced by using Pro-Engineer. The required pan and tilt motor capacities have been analyzed using ADAMS inverse dynamics analysis. A target tracking and stabilization control algorithm of the mobile surveillance robot has been developed in order to compensate the motion of the vehicle which will experience the rough terrain. To test the performance of the stabilization control system of the robot, ADAMS/simulink co-simulations has been carried out.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.3
• /
• pp.1-9
• /
• 2005

In this paper, an operation algorithm and a performance simulator are developed for a 42-volt ISG vehiclewhich consists of 5 kW ISG, 2500cc IC engine, torque converter and 4 speed automatic transmission. Modularapproach using MATLAB Simulink is used to construct a dynamic model of the vehicle powertrain which is obtainedfrom each component such as engine, battery, ISG, torque converter, etc.. An operation strategy for a 42-volt ISG vehicle including the function such as engine idle stop and regenerative braking is proposed. Performance simulator is developed based on the dynamic models of the powertrain. It is found from the simulation results that fuel economy can be improved as much as 6 percent for FTP75 driving cycle mostly owing to the engine idle stop.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.3079-3085
• /
• 2011

Through Korean Urban Maglev Program started in 2006, an urban maglev train was developed and the demonstration line is under construction as of now in 2011. The target speed of the developed maglev train is 110km/h, and the core technologies for super speed maglev trains over 500km/h are being studied. The propulsion and levitation systems of the super speed maglev train under consideration consist of linear synchronous motors (LSM) and levitation electromagnets which also act as a mover of LSM. In addition, guidance electromagnets are used to ensure stable running on curved tracks during super speed operation. The levitation and guidance control is focused on in this paper. For experimental purpose, a small maglev train is being manufactured, and its levitation and guidance controller is studied. The main task of the controller is to maintain the gap between the corresponding electromagnet and the guideway constantly. In general, measurements of the gap, acceleration and current and so on are utilized, and the gap control is implemented independently for each electromagnet. In this paper, the levitation and guidance system is modelled considering mechanical interactions, and the levitation and guidance controller is proposed based on this model. The developed controller is verified by various simulations using MATLAB/Simulink.

• Journal of Power Electronics
• /
• v.15 no.3
• /
• pp.577-586
• /
• 2015

The combination of voltage feedforward and feedback control is a conventional approach for correcting the power factor in single-phase ac-dc boost converters. The feedback duty ratio increases significantly with an increase of the line frequency and input inductance. Therefore, the performance of the conventional approach is highly dependent on the bandwidth of the feedback controller. As a result, the input power quality can be significantly exacerbated due to uncompensated duty ratios if the feedback controller is limited. This paper proposes an input impedance and current feedforward control method to reduce the control portion of the feedback controller. The findings in this paper are 1) the theoretical derivation and analysis of variations of line frequency and input inductance on a power factor correction approach, 2) guaranteed consistent performance in a wide range of conditions, and 3) that a low switching frequency can be utilized by the proposed method. A MATLAB/Simulink model and a 1.2kW dual boost converter are built to demonstrate the effectiveness of the proposed method.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.1
• /
• pp.261-270
• /
• 2015

In this paper, the Optimal Harmonic Stepped Waveform (OHSW) method is proposed in order to eliminate the selective harmonic orders available at the output of cascaded multilevel inverter (CMLI) fed by solar photovoltaic (SPV). This technique is used to solve the harmonic elimination equations based on stepped waveform analysis in order to obtain the optimal switching angles which in turn reduce the Total Harmonic Distortion (THD). The OHSW method considers the output voltage waveform as four equal symmetries in each half cycle. In the proposed method, a solar fed fifteen level cascaded multilevel is considered where the magnitude of six numbers of harmonic orders is reduced. A programmable pulse generator is developed to carry the switching angles directly to the semiconductor switches obtained as a result of OHSW analysis. Simulations are carried out in MATLAB/Simulink in which a separate model is developed for solar photovoltaic which serves as the input for cascaded multilevel inverter. A 3kWp solar plant with multilevel inverter system is implemented in hardware to show the effectiveness of the proposed system. Based on the observation the OHSW method provides the reduced THD thereby improving power quality in renewable energy applications.