• Journal of Electrical Engineering and information Science
• /
• v.3 no.2
• /
• pp.174-183
• /
• 1998

A simple and robust digital current control technique for a permanent magnet (PM) synchronous motor under the parameter variations is presented. Among the various current control schemes for an inverter-fed PM synchronous motor drive, the predictive control is known to give a superior performance. This scheme, however, requires the full knowledge of machine parameters and operating conditions, and cannot give a satisfactory response under the parameter mismatch. To overcome such a limitation, the disturbances caused by the parameter variations will be estimated by using a disturbance observer theory and used for the computation of the reference voltages by a feedforward control. Thus, the steady-state control performance can be significantly improved with a relatively simple control algorithm, while retaining the good characteristics of the predictive control. The proposed control scheme is implemented on a PM synchronous motor using the software of DSP TMS320C30 and the effectiveness is verified through the comparative simulations and experiments.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.6
• /
• pp.748-754
• /
• 1999

The acoustic performance of reactive type single expansion chamber can be calculated theoretically by plane wave theory. But higher order modes should be considered to widen the frequency range. Munjal has suggested the method for analyzing the acoustic properties of simple expansion chamber with taking into consideration of higher order mode of inlet/outlet. But his method cannot predict the acoustic properties exactly when the dimensions of inlet/outlet and expansion chamber have not integer multiples. In this paper the new method was suggested to overcome the shortcomings of Munjal's method The predictions by this method were also compared with those by the finite element method.

• Asian-Australasian Journal of Animal Sciences
• /
• v.25 no.4
• /
• pp.592-596
• /
• 2012

The simple method of evaluating highly marbled beef was examined by image analysis. The images of the cross section at the 6 to 7th rib were obtained from 82 carcasses of Wagyu cattle. By using an overall trace method, the surrounding edges of the longissimus thoracis and three muscles were traced automatically and manually with image analysis. In a spot method, 3 to 5 locations (2.5 or 3.0 cm in diameter) for each muscle were rapidly selected with no manual trace. The images were flattened, binarized, and the ratio of fat area to muscle area was determined. The correlation coefficients for marbling between different muscles, and between the overall trace and the spot methods were 0.55 to 0.81 between different muscles and 0.89 to 0.97, respectively. These results suggested that the simple spot method is speedy and almost as useful as the overall trace method as a measuring technique for beef marbling in loin muscles, especially for highly marbled beef.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.45 no.2
• /
• pp.68-77
• /
• 2003

Shell structure are widely used in a variety of engineering application and mathematical solution of shell structures are available only for a few special cases. The solution of shell structure is more complicated when it has such condition as winker foundation, variable thickness and other problem. In this paper, a simple finite element method is presented for the analysis of axisymmetric several types of shell structure subjected to axisymmetric loads and having uniform and varying wall thickness on elastic foundation. The method is based on the analogy with a beam on elastic foundation (BEF), foundation stiffness matrix where the foundation modulus and beam flexural rigidity are replaced by appropriate parameters pertaining to the shell under considerations. The technique is attractive for implementation on a numerical solution by means of a computer program coded in FORTRAN language with a few elements. To demonstrate this fact, it gives good results which compare well with SAP2000.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2001.04a
• /
• pp.223-232
• /
• 2001

This paper describes Genetic Algorithm-Based Relay Search Method, RS-GA, which is developed in this study to search the multiple design variables in the design space. The RS-GA based on Simple-GA consists of some functions to search many variables from some wide variable space. It repeats a Simple-GA, that is the convergence process of the Simple-GA, which makes many time reiteration itself. From the results of the numerical studies, it was actually found that RS-GA can search all peak-variable from the 2D functions including 5 peaks. Finally, RS-GA applied for design-strengthening problems in composite plate girder bridges using the external prestressing technique is also verified.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.23 no.3
• /
• pp.10-16
• /
• 1986

This paper deals with a simple, approximate formula to predict the natural frequencies of the sagged cable structures. Assuming that the propagation velocity of the lateral wave is dependent only on the local mass per unit length and local tension, the explicit simple formula to predict the fundamental period is newly derived. The modified form of these formula is also presented for the prediction of the fundamental period of general shaped cable structures. The results of comparison shows fairly good agreements with experimental results and with theoretical ones. This formula is also used to predict the natural frequencies of a long vertical cable and the derived approximate formula in that case, becomes identical to the exact solution.

• Journal of KSNVE
• /
• v.9 no.2
• /
• pp.340-347
• /
• 1999

The acoustic performance of reactive type single expansion chamber can be calculated theoretically by plane wave theory. But higher order model should be considered to widen the frequency range. Mode matching method has been developed to consider higher order modes, but very complicated algebra should be used. Munjal suggested a numerical collocation method, which can overcome the shortcomings of mode matching method, using the compatibility conditions for acoustic pressure and particle velocity at the junctions of area discontinuities. But the restriction of Munjal's method is that the ratio between the area of inlet(or outlet) pipe and that of chamber must be natural number. In this paper, the new method was suggested to overcome the shortcomings of Munjal's method. The predictions by this method was also compared with those by the finite element method and Munjal's method in order to demonstrate the accuracy of the modified method presented here.

• Journal of Industrial and Engineering Chemistry
• /
• v.68
• /
• pp.220-228
• /
• 2018

In this study, we found a simple surface biofunctionalization of biphasic calcium phosphate (BCP) based on the high affinity between alendronate and the calcium ions of BCP, and the strong interaction between heparin and bone morphogenic protein-2 (BMP-2). The biofunctionalized BCP did not be precipitated well and display a remarkable enhancement of osteogenic activity of human adipose-derived stem cells by showing increased alkaline phosphatase (ALP), calcium deposition and osteogenic-related genes (i.e., Runx-2, ALP, osteocalcin, and osteopontin), and bone regeneration in the calvarial defect model. Therefore, this simple surface technique can be used to easily functionalize various calcium phosphates.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.3
• /
• pp.331-337
• /
• 2012

In this study, the front side member is optimized using a topography optimization technique. Optimization of a simple beam is conducted before optimization of the front side member. The objective function is set to minimize the first buckling factor in the longitudinal direction. The design variable corresponds to the perturbation of nodes normal to the shell's mid-plane space. The crash analysis is conducted on a simple beam, which is optimized by Response Surface Method and the topography optimization technique. In order to verify the topography optimization technique, the results of the RSM and topography optimization model are compared. Consequently, we confirm the satisfactory performance of the topography optimization technique, and apply this topography optimization to the front side member. Thus, the front side member is optimized and its crashworthiness is increased.

• Geophysics and Geophysical Exploration
• /
• v.8 no.2
• /
• pp.184-190
• /
• 2005

We have attempted to give some physical into the factors that control the response of subsurface target to plane wave excitation at VLF (very low frequency) frequencies. Although the VLF technique has some serious disadvantages, such as a lack of penetration depth and limited frequencies, its advantages are also extremely important to have made it by far the most popular electromagnetic technique in current use. In the magnetic-field measurement mode these lightweight, relatively low-priced tools allow us to survey large areas rapidly and inexpensively, to locate and roughly define subsurface electrical conductors. When used in the electric-field mode the technique is, in simple environments, capable of quantitative interpretation and once again the speed and relative cheapness of these devices makes them a natural 'first electromagnetic tool ' to use in reconnaissance mapping.