• Journal of the Korean institute of surface engineering
• /
• v.29 no.5
• /
• pp.467-473
• /
• 1996

Heteroepitaxial growth of cubic silicon carbide films on Si(001) and Si(111) substrates at temperatures 900-$1000^{\circ}C$ has been achieved by high vacuum chemical vapor deposition using the single precursor 1, 3-disilabutane without carrying out the carbonization process of the substrate surfaces. The deposition temperature range is much lowered compared with conventiontional chemical vapor deposition where separate sources for silicon and carbon are employed. The deposition procedure is quite simple and safe. The qualities of the films were found to be very good judging from the results obtained by various characterization techniques including reflection high energy electron diffraction, X-ray diffraction, X-ray pole figure analysis, Rutherford backscattering spectrometry, Auger depth profiling, and transmission electron diffraction.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.5
• /
• pp.24-31
• /
• 2004

Masking effect of the nanoscratched silicon (100) surface was studied and applied to a maskless nanofabrication technique. First, the surface of the silicon (100) was machined by ductile-regime nanomachining process using the scratch option of the Nanoindenter${ \circledR}$ XP. To clarify the possibility of the nanoscratched silicon surfaces for the application to wet etching mask, the etching characteristic with a KOH solution was evaluated at room temperature. After the etching process, the convex nanostructures were made due to the masking effect of the mechanically affected layer. Moreover, the height and the width of convex structures were controlled with varying normal loads during nanoscratch.

• Laser Solutions
• /
• v.5 no.2
• /
• pp.9-15
• /
• 2002

Basic principles and unique characteristics of laser-induced shock cleaning have been described compared to a conventional laser cleaning method and the removal of small tungsten particles from silicon wafer surfaces was attempted using both methods. It was found that the conventional laser cleaning was not feasible to remove the tungsten particles whereas a successful removal of the particles was carried out by the laser-induced shock waves. From the quantitative analysis using a surface scanner, the average removal efficiency of the particles was more than 98% where smaller particles were slightly more difficult to remove probably due to the increased adhesion force with a decrease of the particle size. It was also seen that the gap distance between the laser focus and the wafer surface is an important processing parameter since the removal efficiency is strongly dependent on the gap distance.

• Progress in Superconductivity and Cryogenics
• /
• v.20 no.4
• /
• pp.20-25
• /
• 2018

Niobium nitride (NbN) superconducting thin films with the thickness of 100 and 400 nm have been deposited on the surfaces of silicon oxide/silicon substrates using a sputtering method. Their superconducting properties have been evaluated in terms of the transition temperature, critical magnetic field, and critical current density. In addition, the NbN films were patterned in a line with a width of $10{\mu}m$ by a reactive ion etching (RIE) process for their characterization. This study proves the applicability of the standard complementary metal-oxide-semiconductor (CMOS) process in the fabrication of superconducting thin films without considerable degradation of superconducting properties.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.6-7
• /
• 2021

Although the development of free-form architectural technology continues, it consumes a lot of money and time due to the one-time formwork and the difficulty of maintaining quality due to manual work. To this end, in this study, a shape connection technique was proposed and verified to improve the limitations of implementing the curved surface of the existing lower multi-point press. In order to improve the accuracy of the shape, a curved surface was implemented using a silicon cap and a silicon plate. As a result of the error analysis of the shape, a small value of less than 3 mm was found. This study can implement more accurate curved surfaces than conventional technologies and produce high-quality free-form panels.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05b
• /
• pp.103-106
• /
• 2002

The applicability of models based on fractal morphology to characterize $(Ba\;Sr)TiO_{3}$ thin film surfaces was investigated. The fractal morphology of coated barium strontium titan oxide thin film surfaces was described using fractal dimension from scanning electro microscopy image. The $(Ba\;Sr)TiO_{3}$ coating were deposited on silicon wafers using $(Ba\;Sr)TiO_{3}$ solution and spin coater. BST solution was composited by mol ratio, and then spin-coated from 3 times to 5 times coating on $Pt/SiO_{2}/Si$ substrate. Qualitative thin film analysis was performed with scanning electro microscopy (SEM), and surfaces parameters such as average grain diameter, roughness exponent and fractal dimension were determined.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2003.11a
• /
• pp.256-259
• /
• 2003

To develop cleaning process various particles should be deposited on wafer surfaces to measure particle removal efficiencies. The purpose of the article in to evaluate, removal efficient)r of silica and alumina particles from wafer surfaces when they are deposited by dry and wet method. Dry deposition in air and wet spray deposition using solutions are used. van der Waals are considered to calculate the adhesion force of particles on surfaces. Higher adhesion force is measured on alumina particles on silicon when particles are deposited in air.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.40-40
• /
• 2010

Employing synchrotron radiation based photoemission spectroscopy (PES) and scanning tunneling microscopy (STM), our group have investigated Si surfaces, various graphenes and molecular nanolayers. In this talk, I introduce recent results on the surface related systems. All experiments have been performed at the surface science beamlines, 3A2 and 7B1, in Pohang Accelerator Laboratory, where high resolution PES (HRPES) and angle resolved PES (ARPES) are available. Metals or molecules are adsorbed and sometimes extreme ultraviolet is irradiated onto surfaces to give them special functions. I show several examples for surface functionalzation and how to characterize solid surface using the analysis techniques. In particular, lots of ARPES and STM data are provided from graphenes, a strong candidate for replacing Si and conducting oxide currently used in many electronic and optical devices.

• KSTLE International Journal
• /
• v.7 no.1
• /
• pp.14-17
• /
• 2006

In this paper, we report on the replication of surface topography of natural leaf of Lotus onto thin polymeric films using a capillarity-directed soft lithographic technique. PDMS molds were used to replicate the surface. The replication was carried out on poly(methyl methacrylate) (PMMA) film coated on silicon wafer. The patterns so obtained were investigated for their friction properties at micro-scale using a ball-on-flat type micro-tribo tester, under reciprocating motion. Soda lime balls (1 mm diameter) were used as counterface sliders. Friction tests were conducted at a constant applied normal load of $3000{\mu}N$ and speed of 1mm/s. All experiments were conducted at ambient temperature ($24{\pm}1^{\circ}C$) and relative humidity ($45{\pm}5%$). Results showed that the patterned samples exhibited superior tribological properties when compared to the silicon wafer and non patterned sample (PMMA thin film). The reduced real area of contact projected by the surfaces was the main reason for their enhanced friction property.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.368-368
• /
• 2010

Monolayers of graphite can be grown by fine controlled surface graphitization on the surfaces of various metallic and semiconducting materials. Epitaxial graphene grown on polished silicon carbide crystal surfaces has drawn much attention due to well known vacuum annealing procedures from surface analysis methods, especially scanning tunneling microscopy(STM) and scanning tunneling spectroscopy(STS). In this study, we have grown single layer and few layer graphene on silicon terminated 6H-SiC(0001) crystals. The growth of graphene layers were observed by low energy electron diffraction(LEED) patterns. Scanning tunneling microscopy and spectroscopy measurements were performed to illustrate the electronic structure which may display some clue on the influence of the underlying structure. Spatially resolved STS results acquired at the edges of epitaxial graphene show in detail the electron density of states, which is compared to theoretical calculations. STM measurements were also done on graphene films grown by chemical vapor deposition(CVD) and transferred onto a SiC(0001) crystal. These observations may provide a hint for the understanding of carrier scattering at the edges.