Environmentally benign lead-free solder coated ribbon (e. g. SnCu, SnZn, SnBi${\cdots}$) has been intensively studied to interconnect cells without lead mixed ribbon (e. g. SnPb) in the crystalline silicon(c-Si) photovoltaic modules. However, high melting point (> $200^{\circ}C$) of non-lead based solder provokes increased thermo-mechanical stress during its soldering process, which causes early degradation of PV module with it. Hence, we proposed low-temperature conductive paste (CP) based tabbing method for lead-free ribbon. Modules, interconnected by the lead-free solder (SnCu) employing CP approach, exhibits similar output without increased resistivity losses at initial condition, in comparison with traditional high temperature soldering method. Moreover, 400 cycles (2,000 hour) of thermal cycle test reveals that the module integrated by CP approach withstands thermo-mechanical stress. Furthermore, this approach guarantees strong mechanical adhesion (peel strength of ~ 2 N) between cell and lead-free ribbons. Therefore, the CP based tabbing process for lead free ribbons enables to interconnect cells in c-Si PV module, without deteriorating its performance.
Dye sensitized solar cells(DSSC) are the most promising future energy resource due to their high energy efficiency, low production cost, and simple manufacturing process. But one problem in DSSC is short life time compared to silicon solar cells. This problem occurred from photocatalytic degradation of dye material by nanometer sized $TiO_2$ particles. To prevent dye degradation as well as to increase its life time, the transparent coating film is needed for UV blocking. In this study, we synthesized nanometer sized $TiO_2$ particles in sols by increasing its internal pressure up to 200 bar in autoclave at $120^{\circ}C$ for 10 hrs. The synthesized $TiO_2$ sols were all formed with brookite phase and their particle size was several nm to 30 nm. Synthesized $TiO_2$ sols were coated on the backside of fluorine doped tin oxide(FTO) glass by ink jet printing method. With increasing coating thickness by repeated ink jet coating, the absorbance of UV region (under 400 nm) also increases reasonably. Decomposition test of titania powders dispersed in 0.1 mM amaranth solution covered with $TiO_2$ coating glass shows more stable dye properties under UV irradiation, compared to that with as-received FTO glass.
Advances in screen printing technology have been led to development of high efficiency silicon solar cells. As a post PERx structure, an n-type wafer-based rear side TOPCon structure has been actively researched for further open-circuit voltage (Voc) improvement. In the case of the metal contact of the TOPCon structure, the poly-Si thickness is very important because the passivation of the substrate will be degraded when the metal paste penetrates until substrate. However, the thin poly-Si layer has advantages in terms of current density due to reduction of parasitic absorption. Therefore, poly-Si thickness and firing temperature must be considered to optimize the metal contact of the TOPCon structure. In this paper, we varied poly-Si thickness and firing peak temperature to evaluate metal induced recombination (Jom) and contact resistivity. Jom was evaluated by using PL imaging technique which does not require both side metal contact. As a results, we realized that the SiNx deposition conditions can affect the metal contact of the TOPCon structure.
The formation of high-quality polycrystalline silicon (poly-Si) on relatively low cost substrate has been an important issue in the development of thin film solar cells. Poly-Si seed layers were fabricated by an inverse aluminum-induced crystallization (I-AIC) process and the properties of the resulting layer were characterized. The I-AIC process has an advantage of being able to continue the epitaxial growth without an Al layer removing process. An amorphous Si precursor layer was deposited on Corning glass substrates by RF magnetron sputtering system with Ar plasma. Then, Al thin film was deposited by thermal evaporation. An $SiO_2$ diffusion barrier layer was formed between Si and Al layers to control the surface orientation of seed layer. The crystallinity of the poly-Si seed layer was analyzed by Raman spectroscopy and x-ray diffraction (XRD). The grain size and orientation of the poly-Si seed layer were determined by electron back scattering diffraction (EBSD) method. The prepared poly-Si seed layer showed high volume fraction of crystalline Si and <100> orientation. The diffusion barrier layer and processing temperature significantly affected the grain size and orientation of the poly Si seed layer. The shorter oxidation time and lower processing temperature led to a better orientation of the poly-Si seed layer. This study presents the formation mechanism of a poly seed layer by inverse aluminum-induced crystallization.
In commercial solar cells, the pattern of the front electrode is critical to effectively assemble the photo generated current. The power loss in solar cells caused by the front electrode was categorized as four types. First, losses due to the metallic resistance of the electrode. Second, losses due to the contact resistance of the electrode and emitter. Third, losses due to the emitter resistance when current flows through the emitter. Fourth, losses due to the shading effect of the front metal electrode, which has a high reflectance. In this paper, optimizing the number of finger on a $4{\times}4$ solar cell is demonstrated with known theory. We compared the short circuit current density and fill factor to evaluate the power loss from the front metal contact calculation result. By experiment, the short circuit current density($J_{sc}$), taken in each pattern as 37.61, 37.53, and $37.38mA/cm^2$ decreased as the number of fingers increased. The fill factor(FF), measured in each pattern as 0.7745, 0.7782 and 0.7843 increased as number of fingers increased. The results suggested that the efficiency(Eff) was measured in each pattern as 17.51, 17.81, and 17.84 %. Throughout this study, the short-circuit current densities($J_{sc}$) and fill factor(FF) varied according to the number of fingers in the front metal pattern. The effects on the efficiency of the two factors were also investigated.
Silicon microwire array is one of the promising platforms as a means for developing highly efficient solar cells thanks to the enhanced light trapping efficiency. Among the various fabrication methods of microstructures, deep reactive ion etching (DRIE) process has been extensively used in fabrication of high aspect ratio microwire arrays. In this presentation, we show precisely controlled Si microwire arrays by tuning the DRIE process conditions. A periodic microdisk arrays were patterned on 4-inch Si wafer (p-type, $1{\sim}10{\Omega}cm$) using photolithography. After developing the pattern, 150-nm-thick Al was deposited and lifted-off to leave Al microdisk arrays on the starting Si wafer. Periodic Al microdisk arrays (diameter of $2{\mu}m$ and periodic distance of $2{\mu}m$) were used as an etch mask. A DRIE process (Tegal 200) is used for anisotropic deep silicon etching at room temperature. During the process, $SF_6$ and $C_4F_8$ gases were used for the etching and surface passivation, respectively. The length and shape of microwire arrays were controlled by etching time and $SF_6/C_4F_8$ ratio. By adjusting $SF_6/C_4F_8$ gas ratio, the shape of Si microwire can be controlled, resulting in the formation of tapered or vertical microwires. After DRIE process, the residual polymer and etching damage on the surface of the microwires were removed using piranha solution ($H_2SO_4:H_2O_2=4:1$) followed by thermal oxidation ($900^{\circ}C$, 40 min). The oxide layer formed through the thermal oxidation was etched by diluted hydrofluoric acid (1 wt% HF). The surface morphology of a Si microwire arrays was characterized by field-emission scanning electron microscopy (FE-SEM, Hitachi S-4800). Optical reflection measurements were performed over 300~1100 nm wavelengths using a UV-Vis/NIR spectrophotometer (Cary 5000, Agilent) in which a 60 mm integrating sphere (Labsphere) is equipped to account for total light (diffuse and specular) reflected from the samples. The total reflection by the microwire arrays sample was reduced from 20 % to 10 % of the incident light over the visible region when the length of the microwire was increased from $10{\mu}m$ to $30{\mu}m$.
Silane($SiH_4$), methane($CH_4$), diborane(B_2H_6)그리고 phosphine($PH_3$)을 이용하여 rf글로방전분해법으로 PIN형 a-SiC:H/a-Si:H 이종접합 태양전지를 제작하였다. $SnO_2/ITO$층 형성치 태양전지의 효율은 ITO 투명전극만의 경우보다 1.5% 향상되었다. 제작조건은 P층의 경우 $CH_4/SiH_4$의 비를 5로 하고 두께는 $100{\AA}$이었다. I층은 P층위에 증착하였으나 진성이 아니고 N형에 가깝다. 이 I층을 진성으로 바꾸기 위해서 0.3ppm의 $B_2H_6$를 $SiH_4$에 혼합하여 5000${\AA}$증착했다. 또한 N층은 $PH_4/SiH_4$의 비를 $10^{-2}$로 하여 $400{\AA}$ 증착시켰다. 그 결과 입사강도가 15mW/$cm^2$일 때 개방전압 $V_{oc}=O'$단락전류밀도 $J_{sc=14.6mA/cm^2}$, 충진율 FF=58.2%, 그리고 효율 ${eta}=8.0%$를 나타내었다. 빛의 반사에 의한 손실을 감소시키기 위하여 $MgF_2$를 유리기판위에 도포하였다. 이에 의한 효율은 0.5% 향상되어 전체적인 효율은 8.5%였다.
건물기능과 디자인을 개선하는 건물일체형 태양전지의 발전 가능성이 높게 평가되고 있다. 현재는 투명 염료감응형 태양전지가 유력한 건물일체형 태양전지 기술로서 개발되고 있는데 박막 공정 기술에 기초하는 Si계 투명 박막 태양전지가 새로운 대안으로서 조명받고 있다. Si계 투명 박막 태양전지에 선택적 투과막을 적용하면 가시광선은 태양전지를 투과하고 적외선은 광 흡수층으로 재반사되기 때문에 변환효율이 향상된다. 본 연구에서는 여러 종류의 박막 증착 기술 중에서 경제성이 높은 스퍼터링 방식을 이용하여 Al-Ti계 산화물 박막을 형성하고 조성에 따른 선택적 투과 특성 변화를 관찰하였다. Al-Ti계 산화물 박막의 투과율 및 반사율은 조성에 따라 크게 변화하였으며 25 nm 두께의 AlTiO 박막에서 선택적 투과 특성이 관찰되었다. 이러한 Al-Ti계 산화물 박막의 광학적 특성을 Si계 박막 태양전지에 응용하면 투명 태양전지 구현 및 변환효율 향상이 가능해 지리라 판단된다.
Plasmonics, sensor, field effect transistors, solar cells 등 다양한 적용분야를 가지는 실리콘 구조체는 제작공정에 의해 전기적 및 광학적 특성이 달라지기 때문에 적합한 나노구조 제작방법이 요구되고 있다. 나노구조체 제작방법으로는 Photo lithography, Extreme ultraviolet lithography (EUV), Nano imprinting lithography (NIL), Block copolymer (BCP) 방식의 방법들이 연구되고 있으며, 특히 BCP는 direct self-assembly 특성을 가지고 있으며 가격적인 면에서도 큰 장점을 가진다. 하지만 BCP를 mask로 사용하여 식각공정을 진행할 경우 BCP가 버티지 못하고 변형되어 mask로서의 역할을 하지 못한다. 이러한 문제를 해결하기 위하여 본 논문에서는 BCP와 질화막을 이용한 double mask 방법을 사용하였다. 기판 위에 BCP를 self-assembly 시키고 mask로 사용하여 hole 부분으로 노출된 기판을 Ion gun을 통해 질화 시킨 후에 BCP를 제거한다. 기판 위에 hole 모양의 질화막 표면은 BCP와 다르게 etching 공정 중 변형되지 않는다. 이러한 질화막 표면을 mask로 사용하여 pillar pattern의 실리콘 나노구조체를 제작하였다. 질화막 mask로 사용되는 template은 PS와 PMMA로 구성된 BCP를 사용하였다. 140kg/mol의 polystyrene과 65kg/mol의 PMMA를 톨루엔으로 용해시키고 실리콘 표면 위에 spin coating으로 도포하였다. Spin coat 후 230도에서 40시간 동안 열처리를 진행하여 40nm의 직경을 가진 PS-b-PMMA self-assembled hole morphology를 형성하였다. 질화막 형성 및 etching을 위한 장비로 low-energy Ion beam system을 사용하였다. Reactive Ion beam은 ICP와 3-grid system으로 구성된 Ion gun으로부터 형성된다. Ion gun에 13.56 MHz의 frequency를 갖는 200W 전력을 인가하였다. Plasma로부터 나오는 Ion은 $2{\Phi}$의 직경의 hole을 가지는 3-grid hole로 추출된다. 10~70 voltage 범위의 전위를 plasma source 바로 아래의 1st gird에 인가하고, 플럭스 조절을 위해 -150V의 전위를 2nd grid에 인가한다. 그리고 3rd grid는 접지를 시켰다. chamber내의 질화 및 식각가스 공급은 2mTorr로 유지시켰다. 그리고 기판의 온도는 냉각칠러를 이용하여 -20도로 냉각을 진행하였다. 이와 같은 공정 결과로 100 nm 이상의 높이를 갖는 40 nm직경의 균일한 Silicon pillar pattern을 형성 할 수 있었다.
일본 Sanyo 사에 의해서 획기적으로 HIT 태양전지가 개발된 바 있다. 이러한 HIT 태양전지는 기존의 확산-접합 Si 태양전지에 비해서 저비용 고효율의 장점을 갖는다: 22% 이상의 변환효율, $200^{\circ}C$ 이하의 공정온도, 낮은 태양전지 온도 의존도, 높은 개방전압. 한편 Sanyo사의 HIT 태양전지는 n-형 Si 웨이퍼를 이용한 반면에, 최근 미국 National Renewable Energy Laboratory는 p-형 Si 웨이퍼를 이용해서 변환효율 19% 대의 HIT 태양전지를 개발한 바 있다. 그 동안 지속적으로 p-형 Si HIT 태양전지를 고효율화하기(< 22%) 위해서 많은 노력이 진행되어 왔지만 이와 같은 노력에도 불구하고 아직 p-형 HIT는 n-형 HIT 태양전지에 비해서 다소 성능면에서 떨어져 있다. 본 연구는 n- 및 p-형 실리콘 웨이퍼로 구성된 HIT 태양전지의 물리적인 차이점에 초점을 맞추고, 결정 및 비정질 실리콘 층의 역할에 대해서 연구하였다. 특히 태양전지 효율을 향상시키는 요소들로서 결정 실리콘의 불순물 준위(n- 및 p-형) 또는 비저항, 비정질 실리콘으로 구성된 emitter 층, intrinsic 층, 경계면이 고려되었다. 그리고 이러한 요소들이 HIT 태양전지에 미치는 영향을 조사하기 위해서 AMPS-1D 컴퓨터 프로그램을 사용하였고, 이를 통해서 HIT 태양전지의 결정 및 비정질 실리콘 층의 역할을 물리적 정량적으로 분석하였다. 본 연구에 적용되는 HIT는 ITO/a-Si:H(p+)/a-Si:H(i)/c-Si(n)/a-Si:H(i)/a-Si:H(n+) 및 ITO/a-Si:H(n+)/a-Si:H(i)/c-Si(p)/a-Si:H(i)/a-Si:H(p+)의 구조로서 다음과 같은 태양전지 특성을 갖는다: n-형 HIT의 경우, fill factor ~ 0.78, 단락전류밀도 ~ 38.1 $mA/cm^2$, 개방전압 0.74 V, 변환효율 22.3 % (그리고 p-형 HIT의 경우, fill factor ~ 0.76, 단락전류밀도 ~ 36.5 $mA/cm^2$, 개방전압 0.69 V, 변환효율 19.4 %).
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.