• 제어로봇시스템학회:학술대회논문집
• /
• 1988.10a
• /
• pp.620-626
• /
• 1988

GaAs solar cells may be the most attractive and efficient power source of a satellite. GaAs is more radiation tolerant and less temperature sensitive than widely used silicon. $Al_{x}$ Ga$_{1-x}$ As/GaAs solar cells have been designed and fabricated by Liquid Phase Epitaxial method. GaAs solar cells, of which structure is about 0.2 .mu.m p$^{+}$ - window layer, 0.6-1.O .mu.m Ge-doped p-layer. 3.mu.m n-GaAs layer and n$^{+}$ - buffer layer, have been characterized as a function of operating temperature from 25 .deg.C to 130 .deg.C. Open circuit voltage decreases linearly with increasing temperature by 1.4-1.51 mV/ .deg.C while degradation of silicon solar cells is about 2.2-2.5 mV/ .deg.C, short circuit current does not increase much with increasing temperature. Relative efficiency decreases with increasing of temperature by about 0.21-0.29 %/ .deg.C. Efficiency degradation of silicon solar cells with temperature is known to be about 0.5%/ .deg.C and our results show GaAs solar cells may be an excellent candidate for concentrated solar cells.ells.

• Advances in nano research
• /
• v.3 no.3
• /
• pp.133-141
• /
• 2015

Influence of Ag nanoparticles on optical and photovoltaic properties of, silicon substrates, silicon solar cells and glass have been investigated. Silver nanoparticles have been fabricated by evaporation of thin Ag layers followed by the thermal annealing. The surface plasmon resonance peak was observed in the absorbance spectrum at 470 nm of glass with deposited silver nanoparticles. It is demonstrated that deposition of silver nanoparticles on silicon substrates was accompanied with a significant decrease in reflectance at the wavelength 360-1100 nm and increase of the absorption at wavelengths close to the band gap for Si substrates. We studied influence of Ag nanoparticles on photovoltaic characteristics of silicon solar cells without and with common use antireflection coating (ARC). It is shown that silver nanoparticles deposited onto the front surface of the solar cells without ARC led to increase in the photocurrent density by 39% comparing to cells without Ag nanoparticles. Contrary to this, solar cells with Ag nanoparticles deposited on front surface with ARC discovered decrease in photocurrent density. The improved performance of investigated cells was attributed to Ag-plasmonic excitations that reduce the reflectance from the silicon surface and ultimately leads to the enhanced light absorption in the cell. This study showed possibility of application of Ag nanoparticles for the improvement of the conversion efficiency of waferbased silicon solar cells instead of usual ARC.

• Current Photovoltaic Research
• /
• v.6 no.1
• /
• pp.17-20
• /
• 2018

The dependency of the photovoltaic performance of p-/n-type silicon solar-cells on the metallic contaminant type (Fe, Cu, and Ni) and concentration was investigated. The minority-carrier recombination lifetime was degraded with increasing metallic contaminant concentration, however, the degradation sensitivity of recombination lifetime was lower at n-type than p-type silicon wafer, which means n-type silicon wafer have an immunity to the effect of metallic contamination. This is because heavy metal ions with positive charge have a much larger capture cross section of electron than hole, so that reaction with electrons occurs much more easily. The power conversion efficiency of n-type solar-cells was degraded by 9.73% when metallic impurities were introduced in the silicon bulk, which is lower degradation compared to p-type solar-cells (15.61% of efficiency degradation). Therefore, n-type silicon solar-cells have a potential to achieve high efficiency of the solar-cell in the future with a merit of immunity against metal contamination.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.192-195
• /
• 2005

The silicon thin film solar cells were fabricated by 13.56 MHz PECVD (Plasma-Enhanced Chemical-Vapor Deposition) and 60 MHz VHF PECVD (Very High-Frequency Plasma-Enhanced Chemical-Vapor Deposition). We focus on textured ZnO:Al films prepared by RF sputtering and post deposition wet chemical etching and studied the surface morphology and optical properties. These films were optimized the light scattering properties of the textured ZnO:Al after wet chemical etching. Finally, the textured ZnO:Al films were successfully applied as substrates for silicon thin films solar cells. The efficiency of tandem solar cells with $0.25 cm^2$ area was $11.8\%$ under $100mW/cm^2$ light intensity. The electrical properties of tandem solar cells were measured with solar simulator (AM 1.5, $100 mW/cm^2)$ and spectral response measurements.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.12
• /
• pp.565-569
• /
• 2006

Plasma enhanced chemical vapor deposition(PECVD) is a well established technique for the deposition of hydrogenated film of silicon nitride (SiNx:H), which is commonly used as an antireflection coating as well as passivating layer in crystalline silicon solar cell. PECVD-SiNx:H films were investigated by varying the deposition and annealing conditions to optimize for the application in silicon solar cells. By varying the gas ratio (ammonia to silane), the silicon nitride films of refractive indices 1.85 - 2.45 were obtained. The film deposited at $450^{\circ}C$ showed the best carrier lifetime through the film deposition rate was not encouraging. The film deposited with the gas ratio of 0.57 showed the best carrier lifetime after annealing at a temperature of $800^{\circ}C$. The single crystalline silicon solar cells fabricated in conventional industrial production line applying the optimized film deposition and annealing conditions on large area substrate of size $125mm{\times}125mm$ (pseudo square) was found to have the conversion efficiencies as high as 17.05 %. Low cost and high efficiency silicon solar cells fabrication sequence has also been explained in this paper.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.434-435
• /
• 2009

The crystalline silicon solar cell where the solar cell market grows rapidly is occupying of about 85% or more. high-efficiency and low cost endeavors many crystalline silicon solar cells. the fabrication processes of high-efficiency crystalline silicon solar cells necessitate complicated fabrication processes and Ti/Pd/Ag contact, however, this contact formation processed by expensive materials. Ni/Cu contact formation is good alternative. in this paper, according to temperature Ni silicide makes, produced Ni/Cu contact solar cell and measured conversion efficiency.

• Current Photovoltaic Research
• /
• v.10 no.3
• /
• pp.84-89
• /
• 2022

c-Si solar cells currently account for more than 90% of the solar energy market. Research on tandem junction solar cells to overcome efficiency limitations is drawing attention at a time when new technologies are being developed to secure the price competitiveness of silicon solar cells. Among several candidate materials for silicon-based tandem solar cells, perovskite has recently been studied as it is suitable for the ease of process as well as for its properties as a tandem solar cell material. In this study, we want to review the research trends and technology limitations of 2-T Perovskite/SHJ tandem junction solar cells.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.2
• /
• pp.55-62
• /
• 1992

Polycrystalline silicon ingots were manufactured using the casting method for polycrystalline silicon solar cells. These ingots were cut into wafers and ten n$^{+}$p type solar cells were made through the following simple process` surface etching, n$^{+}$p junction formation, metalization and annealing. For the grain boundary passivation, the samples were oxidized in O$_2$ for 5 min. at 80$0^{\circ}C$ prior to diffusion in Ar for 100 min. at 95$0^{\circ}C$. The conversion efficiency of polycrystalline silicon solar cells made from these wafers showed about 70-80% of those of the single crystalline silicon solar cell and superior conversion efficiency, compared to those of commercial polycrystalline wafers of Wacker Chemie. The maximum conversion efficiency of our wafers was indicated about 8%(without AR coating) in spite of such a simple fabrication method.

• Transactions on Electrical and Electronic Materials
• /
• v.4 no.4
• /
• pp.22-25
• /
• 2003

High series resistance due to the presence of glass frit is one of the major problems for screen printed silicon solar cells. Cells having electrical parameters below the prescribed values are usually rejected during solar module fabrication. Therefore, it is highly desirable to improve the electrical parameters of the silicon solar cells and thereby to increase the overall production yield. It was observed that, the performance of low quality mono-crystalline silicon solar cells made by standard screen printing technology could be improved remarkably by novel surface treatment. We have chemically treated the surface using sodium hydroxide (NaOH) and silver nitrate ($AgNO_3$) solutions. NaOH treatment helps to reduce the series resistance by decreasing the presence of excess glass frit on the top silver grid contact. The $AgNO_3$ treatment is used to reduce the series resistance comes from the deposition of silver on the grids by filling the holes present (if any) within the grid pattern.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.3
• /
• pp.119-123
• /
• 2013

Most of the world's solar cells in photovoltaic industry are currently fabricated using crystalline silicon. Czochralski-grown silicon crystals are more expensive than multicrystalline silicon crystals. The future of solar-grade Czochralski-grown silicon crystals crucially depends on whether it is usable for the mass-production of high-efficiency solar cells or not. It is generally believed that the main obstacle for making solar-grade Czochralski-grown silicon crystals a perfect high-efficiency solar cell material is presently light-induced degradation problem. In this work, the substitution of boron with gallium in p-type silicon single crystal is studied as an alternative to reduce the extent of lifetime degradation. The diamond-wire sawing technology is employed to slice the silicon ingot. In this paper, the quality of the diamond wire-sawn gallium-doped silicon wafers is studied from the chemical, electrical and structural points of view. It is found that the characteristic of gallium-doped silicon wafers including texturing behavior and surface metallic impurities are same as that of conventional boron-doped Czochralski crystals.