• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 춘계학술대회 논문집
• /
• pp.50-55
• /
• 2003

Atomic force microscope(AFM) techniques are increasingly used for tribological studies of engineering surfaces at scales ranging from atomic and molecular to microscale. AFM with suitable tips is being used for nanofabrication nanomachining purposes. In this paper, machining characteristics of silicon have been investigated by nano indentation and nano scratch. Mechanisms of material removal on the microscale are studied and the Taguchi method is introduced to acquire optimum parameters for nanomachining. This work shows effectiveness of the Taguchi method in nanomachining. Also, Acoustic Emission(AE) is introduced for the monitoring of nanomachining.

• 한국정밀공학회지
• /
• 제17권6호
• /
• pp.185-191
• /
• 2000

Recently, a slightest influence to the circuit can be a great damage because the size of semiconductor smaller. It must be controlled the chippingless dicing process and the precision dicing without any damage to tile circuit. In this study, the relationship between chipping effect and the force of dicing was analysed. The rate of chipping was decreased as the farce of dicing decreased. It was also examined that the farce of dicing decreased according to the lower feed rate and higher blade speed. The lower feed rate and the higher blade speed must be controlled to achieve the chippingless process.

• 센서학회지
• /
• 제17권1호
• /
• pp.35-40
• /
• 2008

Low power bridge type micro gas sensors were fabricated by micro machining technology with TMAH (Tetra Methyl Ammonium Hydroxide) solution. The sensing devices with different heater materials such as metal and poly-silicon were obtained using CMOS (Complementary Metal Oxide Semiconductor) compatible process. The tellurium films as a sensing layer were deposited on the micro machined substrate using shadow silicon mask. The low power micro gas sensors showed high sensitivity to NO with high speed. The pure tellurium film used micro gas sensor showed good sensitivity than transition metal (Pt, Ti) used tellurium film.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.1482-1483
• /
• 2008

This report describes the design, fabrication and experimental results of an implantable micro pressure regulator. It consists of three silicon substrates, a glass substrate, and a PDMS layer. Silicon and glass substrates are fabricated by using bulk micro machining and sandblasting. The PDMS layer is used as a intermediate layer for Si-Si and Si-glass bonding processes. This micro regulator is a key component of the portable drug delivery systems for low power consumption. The device has some advantages, such as a passive type device, no power consumption, and simple structure.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1992년도 춘계학술대회 논문집
• /
• pp.60-65
• /
• 1992

A hypereutectic Aluminum-Silicon Alloyis widely used in the parts of automobile because of high-resistance and good strength. In this study, the cutting of a hypereutectic A1-Si alloy (A390) for extraction of Si particle was experimentally investigatec. By proper selection of cutting tool material and optimization of cutting conditions economical machining of this alloy is achieved. The surface roughness relate closely with the feed rate and cutting speed.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2006년도 제33회 KOSCO SYMPOSIUM 논문집
• /
• pp.235-241
• /
• 2006

Catalytic combustion is one of the suitable methods for micro power source due to high energy density and no flame quenching. Catalyst loading in the micro structured combustion chamber is one of the most important issues in the development of micro catalytic combustors. In this research, to coat catalyst on the chamber wall, two methods were investigated. First, $Al_2O_3$ was selected as a support of Pt and $Pt/Al_2O_3$ was synthesized through the alumina sol-gel procedure. To improve the coating thickness and adhesion between catalyst and substrate, heat resistant and water solvable organic-inorganic hybrid binder was used. Porous silicon was also investigated as a catalyst support for platinum. Through the parametric studies of current density and etching time, fabrication process of $1{\sim}2{\mu}m$ of diameter and about $25{\mu}m$ depth pores was confirmed. Coated substrates were test in the micro channel combustor which was fabricated by the wet etching and machining of SUS 304. Using $Pt/Al_2O_3$ coated substrate and Pt coated porous silicon substrate, conversion rate of fuel was over 95% for $H_2$/Air premixed gas.

• 한국재료학회지
• /
• 제9권2호
• /
• pp.199-204
• /
• 1999

As the engine design change to get high efficiency and performance of commercial diesel engine, surface wear of the cam follower becomes an important issues as applied load increasing at the contact face between cam follower and cam. Purpose of this study is the developing of the ceramic cam follower made of silicon nitride ceramic which is more wear resistant than the cast iron and sintered cam follower. Ceramic cam follower was made by direct brazing of thin ceramic disk to steel can follower body using active bracing alloy. Effect of joining condition on the interfacial phases and joining strength wer examined at bvarious joining temperatures, times, and cooling rates. Crowning resulted from the difference of thermal expansion coefficient after direct brazing without using any stress-relieving inter layer was measured. Interfacial phases are mainly titanium silicide and titanium nitride which are the products between active metal(Ti) in brazing alloy and silicon nitiride. Maximum joining strength of the ceramic metal joint, measured by DBS method, was 334MPa. Crowning(R) of the prototype ceramic cam follower was 1595mm. As machining for crowning is not necessary, production cost can be reduced.

• 한국연소학회지
• /
• 제11권2호
• /
• pp.7-14
• /
• 2006

Catalytic combustion is one of the suitable methods for micro power source due to high energy density and it can be applied to micro structured chamber without consideration of quenching since it is flameless combustion. Catalyst loading in the micro structured combustion chamber is one of the most important issues in the development of micro catalytic combustors. In this research, to coat catalyst on the chamber wall, two methods were investigated. First, $Al_2O_3$ was selected as a support of Pt and $Pt/Al_2O_3$ was synthesized through the alumina sol-gel procedure. To improve the coating thickness and adhesion between catalyst and substrate, heat resistant and water solvable organic-inorganic hybrid binder was used. Porous silicon was also investigated as a catalyst support for platinum. Through the parametric studies of current density and etching time, fabrication process of $1{\sim}2{\mu}m$ of diameter and about $25{\mu}m$ depth pores was confirmed. Coated substrates were test in the micro channel combustor which was fabricated by the wet etching and machining of SUS 304. Using $Pt/Al_2O_3$ coated substrate and Pt coated porous silicon substrate, conversion rate of fuel was over 95 % for $H_2/Air$ premixed gas.

• 한국세라믹학회지
• /
• 제40권8호
• /
• pp.770-776
• /
• 2003

(111) 및 (100) 단결정 실리콘 웨이퍼에 대하여 #140 mesh와 #600 mesh의 연삭숫돌을 사용하여 연삭가공을 행하고 가공에 의한 표면품위의 변화를 관찰하였다. 이를 위하여 Atomic Force Microscope(Am)을 사용하여 미세거칠기를 분석하고 라만 분광법(Raman spectroscopy)을 통하여 결정구조, 상변화 및 잔류응력을 분석하였다. 그 결과 연삭가공 후에 (111) 면에서 미세거칠기가 더 크게 나타났으며 실리콘이 다이아몬드구조의 Si-I에서 Si-III(body centered tetragonal) 및 Si-XII(rhombohedral)로 전이하는 현상을 라만스펙트럼 분석을 통해 확인하였다. 또한 연삭가공에 의하여 패인 구덩이에서는 일반적인 가공표면과 다른 라만스펙트럼이 관찰되어, 표면에 인가된 잔류응력이 새로운 표면생성으로 해소되었음을 알수 있었다. 또한 열처리에 의한 재료의 표면품위개선효과를 분석하기 위하여 대기 중에서 열처리를 시행한 결과 열처리는 잔류응력의 해소와 상전이의 회복에 효과적인 것으로 나타났다.

• 한국재료학회지
• /
• 제15권9호
• /
• pp.589-593
• /
• 2005

Nanoimprinting lithography (NIL) is known as a suitable technique for fabricating nano and micro structures of high definition. Hot embossing is one of NIL techniques and can imprint on thin films and bulk polymers. Key issues of hot embossing are time and expense needed to produce a stamp withstanding a high temperature and pressure. Fabrication of a metal stamp such as an electroplated nickel is cost intensive and time consuming. A ceramic stamp made by silicon is easy to break when the pressure is applied. In this paper, a plastic stamp using a high temperature epoxy was fabricated and tested. The plastic stamp was relatively inexpensive, rapid to produce and durable enough to withstanding multiple hot embossing cycles. The merits of low viscosity epoxy solutions were a fast degassing and a rapid filling the microstructures. The hot embossing process with plastic stamp was performed on PMMA substrates. The hot embossing was conducted at 12.6 bar, $120^{\circ}C$ and 10 minutes. An imprinted PMMA wafer was almost same value of the plastic stamp after 10 times embossing. Entire fabrication process from silicon master to plastic stamp was completed within 12 hours.