• Journal of Positioning, Navigation, and Timing
• /
• v.10 no.1
• /
• pp.21-28
• /
• 2021

In order to develop a Korea Positioning System (KPS) as part of key national infrastructure, independent navigation signal design is essential. The designed signal candidates must coexist with existing or planned GNSS signals within the limited frequency band. This requires a RF compatibility assessment, which can be performed using the Spectral Separation Coefficient (SSC) and Effective Carrier to Noise Density Ratio (Effective C/N0), for navigation signals. Thus, in this paper, the analysis of RF compatibility between the designed signal candidates and the existing GNSS signals is carried out based on analytical and numerical techniques.

• Proceedings of the KIEE Conference
• /
• 1988.07a
• /
• pp.179-182
• /
• 1988

Since the bits in any encoded PCM word are of different importance to the bit positions, in order to improve the signal to noise ratio the technique that the encoded signal bits are weighted for the QPSK transmission system, is presented. Also the erasure zone is established at the detector, such that if the output falls into the erasure zone, the regenerated sample is replaced by interpolation. Two weighting methods are shown here. One is the method that the same weighting profile is used to Q and I dimension in QPSK signal constellations. The other is diferent weighting to Q and I dimension. The gains of this new technique in overall signal s/n compared to conventional QPSK transmission system were 5 db and 2db, respectively.

• Journal of Biomedical Engineering Research
• /
• v.15 no.1
• /
• pp.71-76
• /
• 1994

In the source localization using single dipole model, the influence of the number of electrodes, the position and direction of a single dipole on the relation between S/W ratio and dipole parameter estimation errors is important. Monte Carlo simulation was used to investigate this influence. The forward problem was calculated using three spherical shell model, and dipole parameters were optimized by means of simplex method. As the number of electrodes became large, as the dipole went from midbrain to cortex, and as the direction of dipole changed from radial to tangential, the average and standard deviation of estimation errors became small.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.907-910
• /
• 1995

Though SLA(Stereolithography Apparatus) is being recognized as an innovative technology, it still can not be used to fully practical applications since it lacks of dimensional accuracy compared to conventional processes. In SLA, the accuracy of cured part depends upon the set of process parmeters. In order to improve the accuracy of SLA, this paper quantitatively evaluates how largely each process parameter of SLA contributes to the part accuracy and estimates the optimal set of process parameter which minimizes the dimensional errors of the test part, "letter-H" part. For this purpose, we use ANOVA(analysis of variance) and S/N(signal-to-noise)ratio of Taguchi method.hi method.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.2
• /
• pp.83-91
• /
• 2003

Pantograph design Process must be considered in terms of stability of aerodynamics and reduction of aeroacoustics. Furthermore pantograph needs to be insensible to severe circumstance condition like typhoon, tunnel, a change of season. In this paper, robust design of panhead sections is conducted based on the Taguchi's design of experiment method. In the aeroacoustic noise analysis, an acoustic analogy using the Ffowcs Williams and Hawkings(FW-H) equation is used to calculate the flow induced sound pressure level in aeroacoustics. From the near-field CFD analysis data, the far-field noise is predicted at the positions of 25 m away from Pantograph. Based on aerodynamic(CFD) and aeroacoustic(FW-H) analysis data, the optimal sizing and Positioning of panhead elements are determined using robust design optimization method. Design parameters such as thickness, length and radius are controllable factors, while outdoor air temperature and atmospheric pressure are considered as uncontrollable factors in the context of Taguchi's approach. A number of CFD simulation and aeroacoustic analysis are performed based on orthogonal arrays. In this paper, two-step optimization method is used as a parameter design procedure. It is executed using signal to noise(S/N) ratio and analysis of means(ANOM) method. So Thus, an optimal level of design parameters Is extracted to minimize the disconnection ration between contact strips and catenary system, and reduce the far-field aeroacoustic noise.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.1C
• /
• pp.131-137
• /
• 2009

Binary offset carrier (BOC) signal synchronization is one of the most important steps to recover the transmitted information in global navigation satellite systems (GNSS) including Galileo and global positioning system (GPS). Generally, BOC signal synchronization is based on the correlation between the received and locally generated BOC signals. Thus, the multiple side-peaks in BOC autocorrelation are one of the main error sources in synchronizing BOC signals. Recently, a novel correlation function with reduced side-peaks was proposed for BOC signal synchronization by Julien [8]; however, Julien's correlation function not only still has the side-peaks, but also is only applicable to sine phased BOC(n, n), where n is the ratio of the pseudo random noise (PRN) code rate to 1.023 MHz. In this paper, we propose a new correlation function for BOC signal synchronization, which does not have any side-peaks and is applicable to general types of BOC signals, sine/cosine phased BOC(kn, n), where k is the ratio of a PRN chip duration to the period of a square wave sub-carrier used in BOC modulation. In addition, an efficient correlator structure is presented for generating the proposed correlation function.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.10
• /
• pp.148-158
• /
• 2012

This paper presents the design of the incremental delta-sigma ADC. The proposed circuit consists of pre-amplifier, S & H circuit, MUX, delta-sigma modulator, and decimation filter. Third-order discrete-time delta-sigma modulator with 1-bit quantization were fabricated by a $0.18{\mu}m$ CMOS technology. The designed circuit show that the modulator achieves 87.8 dB signal-to-noise and distortion ratio (SNDR) over a 5 kHz signal bandwidth and differential nonlinearity (DNL) of ${\pm}0.25$ LSB, integral nonlinearity (INL) of ${\pm}0.2$ LSB. Power consumption of delta-sigma modulator is $941.6{\mu}W$. It was decided that N cycles are 200 clock for 16-bits output.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.5
• /
• pp.733-739
• /
• 1987

In this paper, variable threshold detection with weighted pulse code modulation-encoded signals transmitted over Gaussian channels has been investigated. Each bit in the \ulcornerlaw PCM word is weighted according to its significance in the transmitter. It the output falls into the erasure zone, the regenerated sample replaced by interpolation or prediction. To overall system signal to noise ratio for BPSK/PCM speech signals of this technique has been found. When the input signal level was -17 db, the gains in overall signal s/n compared to weighted PCM and variable threshold detection were 5 db and 3 db, respectively. Computer simulation was performed generating signals by computer. The simulation was in resonable agreement with our theoretical prediction.

• Bulletin of the Korean Chemical Society
• /
• v.24 no.7
• /
• pp.971-974
• /
• 2003

By utilizing singular value decomposition (SVD) and shift averaged Harr wavelet transform (WT) with a set of Daubechies wavelet coefficients (1/2, -1/2), a method that can simultaneously eliminate an unwanted large solvent peak and noise peaks from NMR data has been developed. Noise elimination was accomplished by shift-averaging the time domain NMR data after a large solvent peak was suppressed by SVD. The algorithms took advantage of the WT, giving excellent results for the noise elimination in the Gaussian type NMR spectral lines of NMR data pretreated with SVD, providing superb results in the adjustment of phase and magnitude of the spectrum. SVD and shift averaged Haar wavelet methods were quantitatively evaluated in terms of threshold values and signal to noise (S/N) ratio values.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.2
• /
• pp.79-84
• /
• 2017

This paper outlines the Taguchi optimization methodology, which is applied to optimize cutting parameters in end milling when machining STS304 with TiAlN coated SKH59 tool under up and down end milling conditions. The end milling parameters evaluated are depth of cut, spindle speed and feed rate. An orthogonal array, signal-to-noise (S/N) ratio and analysis of variance (ANOVA) are employed to analyze the effect of these end milling parameters. The Taguchi design is an efficient and effective experimental method in which a response variable can be optimized, given various control and noise factors, using fewer resources than a factorial design. An orthogonal array of $L_9(33)$ was used. The most important input parameter for cutting force, however, is the feed rate, and depending on the cutter rotation direction. Finally, confirmation tests verified that the Taguchi design was successful in optimizing end milling parameters for cutting force.