• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.2
• /
• pp.75-82
• /
• 2000

In this Paper, a new type of feedforward linearizer using a delay line which controls the phase characteristics of the correction amplifier block is proposed. The extra delay line provides the control-ability of IM signals so that the IM rejection is accomplished without the conventional pilot tone. The error signal loop consists of several key components such as phase shifter and attenuator, subtractor. These key components are replaced by new designs in order to obtain better linearization characteristics without the pilot tone generator which is indispensable in the conventional linearizer designs. The proposed linearizer was designed at Korean PCS band and combined with 35W HPA manufactured by KMW inc., and tested with two-tone signals separated 0.6MHz apart at the center frequency of 1855MHz. The experimental results show C/l improvement by 16.9 ~ 24.6 dB over 15 dB dynamic range(30 ~45 dBm) which gave IMD of 58.5~63.2 dBc for the designed LPA.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.37 no.4
• /
• pp.65-71
• /
• 2000

Finite wordlength effect of the recursive implementation of SDFT(sliding-DFT) is analytically derived in this paper. Representation errors of the twiddle coefficients and the data registers are the two major causes of the spectral errors in the recursive implementation. The noise-to-signal ratio is analytically derived in terms of the coefficients wordlength, the data registers wordlength, and the DFT's block-length used in the computation Error dynamic equation is obtained from the recursive DFT and the probabilistic models for the coefficients error and the round-off error are introduced for the NSR derivation, The result of the NSR derivation is verified with the simulation data.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.16 no.2
• /
• pp.161-170
• /
• 2017

The balise is a device for the railroad signal control systems, which is installed between both rail. The balise sends fixed or variable data, named telegram, to the train with wireless method. The telegram includes the position information, the movable distance under the signal status, the gradient, the speed, the temporary speed limit, etc. This research is on a design of the DBPL encoder for the balise. Normally the DBPL encoder for the balise is with the ASIC or FPGA technology. In this research, the DBPL encoder is designed with commercial low power operable micro-controller. The firmware(logic level encode) and the SPI Bus function block(physical level output) of the micro-controller are used for the DBPL encode. Under the european standard, the required working speed of the DBPL encoder is 564.48Kbps. The DBPL encoder of this research is tested under the speed of 564.48Kbps, and it worked properly.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.12
• /
• pp.1365-1372
• /
• 2014

In recent, the LTE(Long-Term Evolution) mobile communication system has been commercialized and a variety of service is being provided. Comparing to the old wireless access systems such as 3G mobile communications, in particular, the LTE system supports a service requiring a high transmission rate by providing broadband wireless access. In order to understand the possibility of successful support of a multimedia service such as IPTV(Internet Protocol Television) through the LTE system, it is necessary to understand the mechanism that decides the transmission rate supported by the LTE system. This paper, therefore, discusses on the relationship between a number of metrics such as CQI and BLER that affects the transmission rate with the measurement results from the field tests.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.05a
• /
• pp.947-950
• /
• 2015

In the cause of car accidents in Korea, drowsy driving has shown that it is larger fctors than drunk driving. Therefore, in order to prevent drowsy driving accidents, drowsiness detection and warning system for drivers has recently become a very important issue. Furthermore, Many researches have been published that measuring alpha wave of EEG signals is the effective way in order to be aware of drowsiness of drivers. In this study, we have developed EEG measuring device that applies a signal processing algorithm using the LabView program for detecting drowsiness. According to results of drowsiness inducement experiments for small test subjects, it was able to detect the pattern of EEG, which means drowsy state based on the changing of power spectrum, counterpart of alpha wave. After all, Comparing to the results of drowsiness pattern between commercial equipments and developed device, we could confirm acquiring similar pattern to drowsiness pattern. With this results, the driver's drowsiness prevention system expect that it will be able to contribute to lowering the death rate caused by drowsy driving accidents.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.42 no.2
• /
• pp.323-330
• /
• 2017

The millimeter wave band is in the extremely high frequency band whose frequency and wavelength are 30-300GHz and 10-1mm respectively. When the obstacles block the propagation path which is not Line-of-Sight (LoS), due to a high propagation loss, it is hard to receive a signal in the millimeter wave band. Therefore When the path loss is measured in the millimeter wave band, the signal which is not distinguished from the noise is observed. Consequently, the path loss data which is limited in certain value is observed in the high propagation loss environment. If the original least square is implemented without taking the limitation of certain value into account, the path loss exponent may be underestimated. In this paper, the performance of Tobit Maximum Likelihood Estimation, Heckman Two-stage Model and Truncation Regression Model which can estimate properly in the censoring or truncated environments are compared.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.11
• /
• pp.74-84
• /
• 2000

This paper deals with procedures for design and implementation of a DSP, which is compatible with TMS320C30 DSP. CBS(Cycle Based Simulator) is developed to study the architecture of the target DSP. The simulator gives us detailed information such as function block operation, control signal values, register condition, bus and memory values when a instruction is being carried out. RTL design is carried out by VHDL. Logic simulation and hardware emulation are employed to verify proper operation of the design. The DSP is fabricated with 0.6${\mu}m$ CMOS technology. The Chip has 450,000 gates complexity, $9{\times}9mm^2$ area, 20 MIPS operation speed. It is confirmed by running 109 instructions out of 114 instructions and 13 kinds of algorithm that the developed DSP has compatibility with TMS320C30.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.3
• /
• pp.51-59
• /
• 2009

This paper presents the design of continuous-time sigma-delta modulator for acoustic sensor. The feedforward structure without summing block is used to reduce power consumption of sigma-delta modulator. A high-linearity active-RC filter is used to improve resolution of sigma-delta modulator. Excess loop delay problem in conventional continuous-time sigma-delta modulators is solved by our proposed architecture. A low power, high resolution fourth-order continuous-time sigma-delta modulator with 1-bit quantization was realized in a 0.13-${\mu}m$ 1-Poly 8-metal CMOS technology, with a core area of $0.58\;mm^2$. Simulation results show that the modulator achieves 91.3-dB SNR over a 25-kHz signal bandwidth with an oversampling ratio of 64, while dissipating $290{\mu}W$ from a 3.3-V supply.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.1 s.343
• /
• pp.127-132
• /
• 2006

This paper presents a dual-mode amplifier which operates as amplifier or frequency multiplier according to the input frequency. It satisfies the 802.11a/b/g frequency band of wireless LAN standard. A conventional dual-band wireless LAN transmitter consists of the separating power amplifiers operating at each frequency band, but the proposed dual-mode amplifier operates as an amplifier for the 802.11b/g signal and as a frequency multiplier for the 802.11a signal according to each LAN bias condition. The amplifier mode shows the gain of 13dB, the PldB of 17dBm and second harmonic suppression of below -37dBc. And the frequency-doubler mode shows the gain of 3.3dB, the output power of 7.3dBm and third harmonic suppression of below -50dBr.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.43 no.6 s.312
• /
• pp.76-82
• /
• 2006

In this paper, the biomedical signal compression method, which is combined with the multi-stage vector quantization and wavelet lifting scheme, is proposed. It utilizes the property of wavelet coefficients that give emphasis on approximation coefficients. The transmitted codebook index consists of the code vectors obtained by wavelet lifting coefficients of ECG and error signals from the 1024 block length, respectively. Each codebook is adaptively updated by the method comparing to the distance of input codevectors with candidate codevectors by using an pre-defined threshold value. The proposed compression method showed blow 3% in term of PRD and 276.62 bits/sec in term of CDR.