• 대한의용생체공학회:의공학회지
• /
• 제30권6호
• /
• pp.503-509
• /
• 2009

The development of technology has led to ubiquitous health care service, which enables many patients to receive medical services anytime and anywhere. For the ubiquitous health care environment, real-time measurement of biomedical signals is very important, and the medical instruments must be small and portable or wearable. So, such devices have been developed to measure biomedical signals. In this study, we develop the biomedical monitoring device which is sensing the PPG signal, one of the useful signal in the field of ubiquitous healthcare. We design a watch-like biomedical signal monitoring system without a finger probe to prevent the user's inconvenience. This system obtains the PPG from the radial artery using a sensor in the wrist band. But, new device developed in this paper is easy to get the motion artifacts. So, we proposed new algorithm removing the motion artifacts from the PPG signal. The method detects motion artifacts by changing the degree of brightness of the light source. If the brightness of the light source is reduced, the PPG pulses will disappear. When the PPG pulses have disappeared completely, the remaining signal is not the signal that results from the changing blood flow. We believe that this signal is the motion artifact and call it the noise reference signal. The motion artifacts are removed by subtracting the noise reference signal from the input signal. We apply this algorithm to the system, so we can stabilize the biomedical monitoring system we designed.

• 조명전기설비학회논문지
• /
• 제28권12호
• /
• pp.84-89
• /
• 2014

This paper proposes the new multiple signal processing monitoring sensor for the marine installation. The recent marine technology is focused on underwater sensors and underwater sensor networks in order to measure, monitor, surveillance of and control of underwater environments. For these marine applications to be available, however, the provision of precise location information using monitoring sensor is essential. In this paper, the multiple signal processing circuit for obtaining the precise location information of marine installation sensor is developed and analyzed. The performance characteristics for obtaining the location information of marine installation sensor is analyzed. The theoretical and experimental studies have been carried out. The presented results from the above investigation show considerably excellent performance for the monitoring for the marine installation.

• 융합신호처리학회논문지
• /
• 제16권2호
• /
• pp.56-62
• /
• 2015

본 연구에서는 현대인들의 일상생활 중 대부분의 시간을 보내는 좌식생활 중에 무구속적으로 장시간 심장활동상태를 모니터링하기 위한 의자형 무구속 심전도 모니터링 시스템을 설계 및 구현하였다. 구현된 시스템은 옷을 입은 상태에서도 측정이 가능하며, 동잡음에도 비교적 강한 장점을 가진다. 이를 위하여 의자의 등받이 부분에 무구속 전극을 배치하였으며, 미세한 생체신호를 증폭하고, 측정 시 발생 할 수 있는 동잡음 및 기저선의 변화, 상용전원에 의한 전원잡음을 제거하기 위하여 증폭기 및 필터를 설계하였다. 또한 제어부와 무선전송부를 구현하여 아날로그 신호를 디지털 신호로 변환하고 생체신호를 PC와 스마트폰으로 전송함으로써 일상생활 중 지속적인 심장활동 상태의 모니터링이 가능하다. 구현된 시스템의 성능을 평가하기 위하여 Ag/AgCl 전극을 사용한 시스템과 비교 실험을 수행하였으며, 실험 결과 구현된 시스템의 무구속적으로 심장활동 상태 모니터링이 가능함을 확인하였다.

• Journal of information and communication convergence engineering
• /
• 제13권3호
• /
• pp.167-171
• /
• 2015

A radio over fiber (RoF) system is a kind of analog optical transmission system and considered as a strong candidate for the next-generation fronthaul link in the future mobile network. In RoF systems, nonlinearity compensation is essential to increase the link capacity. In this paper, we propose a nonlinearity detection and compensation scheme using a monitoring channel in RoF systems. A monitoring channel is added at the transmitter site and used for transmitting a reference signal in an RoF transmission. The nonlinearity in the RoF transmission is detected by comparing the received monitoring signal and the original reference signal at the receiver site. Finally, the nonlinearity is compensated at the receiver by giving the reverse function of the detected nonlinearity. Our results show that the proposed scheme can almost remove the error vector magnitude degradation induced by the nonlinearity in the RoF system.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1999년도 추계종합학술대회 논문집
• /
• pp.925-928
• /
• 1999

A multi-channel gas leakage monitoring system was designed and fabricated by using CPLD(complex Programmable Logic .Device) for monitoring and controlling the leakage of natural gas from supplying-pipes under the ground. Fabricated SnO$_2$thick film gas sensor elements were attached on safeguard steel plate of natural gas supplying pipes, and the local monitoring system in this study received the signal from the gas sensors. The monitoring system was implemented by using CPLD chip to reduce the development time and implement simple one chip system. The time division multi-channel system received the input signal from individual gas sensor at one of divided times by multiplexor and signal processed sequentially. The system reduced the size of peripheral circuit resulted in implementation of creditable simple system.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제55권1호
• /
• pp.20-25
• /
• 2006

We suggest a novel temperature detection method utilized in temperature monitoring system. Suggested method detects temperature variation by using $R_{ds(on)}$ characteristics of MOSFET, while conventional methods are using extra devices such as a temperature sensor or an over-temperature detection transistor. For voltage detection between drain and source, 10 bits resolution ADC is needed. Therefore possible measurement signal range is about ten mV. If detected temperature's voltage exceed protection temperature's voltage then controller generates OT (Over Temperature) signal to stop MOSFET's trigger signal. Whole process of measurement is controlled by software. Experimental results show that the developed temperature monitoring system can provide the suitable temperature monitoring method and difference between detected and data sheet value of the suggested system is about $3\%$.

• 한국생산제조학회지
• /
• 제7권1호
• /
• pp.69-74
• /
• 1998

In order to monitor the tool wear in milling operation, cutting force is measured as the tool wear increased. The digital signal processing methods are used to detect the tool wear . As AR parameter extract the feature of tool wear , it can be used as input parameter of pattern classifier. The FFT monitor the tool wear exactly , but it can not do real time signal processing. The band energy method can be used to real time monitoring of tool wear ,but int can degrade the exact monitoring.

• 대한기계학회논문집
• /
• 제16권1호
• /
• pp.156-161
• /
• 1992

본 연구에서는 이송축 직류 서보 모터의 전류신호와 NC정보를 이용해서 선삭 가공상태를 감시하는 시스템을 개발하였다. 모터 전류는 가공 부하의 상태를 잘 나 타내며, NC 장치에 내장되어 있기 때문에 신호 검출을 위한 별도의 센서가 필요 없어 서 공구가 수시로 바뀌는 NC작업 감시를 위한 유효한 신호이다. 또 NC 정보로부터 작업을 예측함으로써 감시 대상을 명확히 하고 신뢰성을 높이고자 하였다. 전체적인 감시 시스템의 프로그래밍 언어로는 C를 사용하여, 실시간 감시처리를 가능하게 하였 다.

• 한국항공운항학회지
• /
• 제18권1호
• /
• pp.11-18
• /
• 2010

GNSS(Global Navigation Satellite System) Ground Station performs GNSS signal acquisition and processing. This system generates error correction information and distributes them to GNSS users. GNSS Ground Station consists of sensor station which contains receiver and meteorological sensor, monitoring and control subsystem which monitors and controls sensor station, control center which generates error correction information, and uplink station which transmits correction information to navigation satellites. Monitoring and control subsystem acquires and processes navigation data from sensor station. The processed data is transmitted to GNSS control center. Monitoring and control subsystem consists of data acquisition module, data formatting and archiving module, data error correction module, navigation determination module, independent quality monitoring module, and system maintenance and management module. The independent quality monitoring module inspects navigation signal, data, and measurement. This paper introduces independent quality monitoring and performs the analysis using measurement data.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 춘계학술대회 논문집
• /
• pp.130-134
• /
• 1996

The characteristics of AE(Acoustic Emission) signal is related to cutting conditio, tool material, and tool geometry in metal cutting. The relation between AE signal and tool life was investigated experimentally. Experiment is carried out by gear shaping and SCM 420 workpiece. AE RMS voltage were increased according totool wear. It is suggested that maximum value of AE RMS voltage is an effective parameter to monitor tool life.