• The Journal of the Acoustical Society of Korea
• /
• v.14 no.4
• /
• pp.5-11
• /
• 1995

In this paper, we design the new high-speed seek algorithm which can access the data of disk (in 3.5-inch optical disk drive). When seek the target track on optical disk in high-speed using the ref-T. E(Reference Tracking Error) and sample pulse signal, it's always possible high-speed seek without re-check and compensation for error by the ref_T. E and sample pulse signal. The performance test result is represented as follow ; it is satify the average seek time of 28mses.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.12 no.9
• /
• pp.702-708
• /
• 2002

The spectrum of impulse response signal from an impulse hammer testing is widely used to obtain frequency response function(FRF). However the FRFs obtained from impact hammer testing have not only leakage errors but also finite record length errors when the record length for the signal processing is not sufficiently long. The errors cannot be removed with the conventional signal analyzer which treats the signals as if they are always steady and periodic. Since the response signals generated by the impact hammer are transient and have damping, they are undoubtedly non-periodic. It is inevitable that the signals be acquired for limited recording time, which causes the errors. This paper makes clear the relation between the errors of FRF and the length of recording time. A new method is suggested to reduce the errors of FRF in this paper. Several numerical examples for 1-dof model are carried out to show the property of the errors and the validity of the proposed method.

• Journal of the Institute of Convergence Signal Processing
• /
• v.9 no.1
• /
• pp.10-17
• /
• 2008

The purpose of this thesis is to reduce of error for source location through acoustic emission(AE) signal, generated elastic wave from crack growth to leak for facility diagnosis. Especially, in order to overcome noise from original signal, this paper proposed enhancement of source location by using noise reduction based on wavelet transform. To evaluate actual performance in experiments, Pencil Lead Break is used crack signal source on the aluminum plate and drain valve of air compressor is used as substitute pressure vessel to generate leak signal. In signal processing, wavelet shrinkage and soft threshold are used to discriminate signal source and then source location techniques have been effectively used with group velocity using material property and time difference between sensor using cross correlation. Source location for crack and leak test have some difference, but the result show that improved 30% with a average length within 10.46mm in crack test and improved 2% compare with average filter in leak test when we applied wavelet transform.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1854-1858
• /
• 2007

The reliability assurance with respect to the test procedure and results of the out-pile mechanical performance test for the nuclear fuel assembly is an essential task to assure the test quality and to get a permission for fuel loading into the commercial reactor core. For the case of vibration test, which is carried out to obtain basic dynamic characteristics of the fuel assembly, proper management and appropriate calibration of instruments and devices used in the test, various efforts to minimize the possible error during the test and signal acquisition process are needed. Additionally, the deep understanding both of the theoretical assumption and simplification cation for the signal processing/modal analysis and of the functions of the devices used in the test were highly required. Finally, to verify the test result to represent the accurate natural characteristics of the structure, the proper correlation analysis between the theoretical and experimental method has to be carried out. In this study, the overall procedure and result of lateral vibration test for the fuel assembly's mechanical characterization were briefly introduced. A series of measures to assure and improve the reliability of the vibration test were discussed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.71-77
• /
• 2002

The spectrum of impulse response signal which is obtained from an impulse hammer testing is used for frequency response function, nevertheless it has serious faults when the record length for the signal processing is not very long. The faults cannot be avoided with the conventional signal analyzer that is processing all the signals as if they are always periodic. The signals generated by the impact hammer are undoubtedly non-periodic because of the damping, and are acquired for limited recording time due to the memory as well as the computation performance of the signal analyzer. This paper will make clear the relation between the faults and the length of recording time, and propose the way for solving the faults.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.1
• /
• pp.14-19
• /
• 2016

Transmission error (TE) is the most important cause of gear noise and vibration because TEs affect the changes of the force and the speed of gears. TE is usually expressed as an angular deviation, or a linear deviation measured at the pitch point and calculated at successive positions of the pinion as it goes through the meshing cycle. Accurate measurement of TE for gear transmission will provide a reasonable basis for gear design, manufacturing processes and quality control. Therefore, in order to study the accuracy of the gear transmission, stability, TE, vibration and noise after gear micro-geometry modification, a gear transmission test rig is proposed in this paper, which is based on the existing technical conditions, by using reasonable testing methods, hardware and a signal processing method. All of the details and the experience can be taken into consideration in the next upgraded test rig.

• Journal of Positioning, Navigation, and Timing
• /
• v.2 no.1
• /
• pp.33-40
• /
• 2013

In this paper, GPS signal anomaly generation software is proposed which can be used for the analysis of GPS signal anomaly effect and the design, verification, and operation test of anomalous signal monitoring technique. For the implementation of anomalous signal generation technique, anomalous signals are generated using a commercial signal generation simulator, and their effects and characteristics are analyzed. An error model equation is proposed from the result of analysis, and the anomalous signal generation software is constructed based on this equation. The proposed anomalous signal generation software has high scalability so that users can easily utilize and apply, and is economical as the additional cost for purchasing equipment is not necessary. Also, it is capable of anomalous signal generation based on real-time signal by comparing with the commercial signal generation simulator.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.11
• /
• pp.1148-1156
• /
• 2009

ETRI has developed GNSS digitized IF signal generator for providing test and evaluation environment for various software level application and navigation algorithm in Global Navigation Satellite System(GNSS). GNSS digitized IF signal generator provides two main capabilities, GPS and Galileo raw data generation and digitized IF signal generation. GNSS digitized IF signal generator consists of five main modules which are GNSS Satellite Orbit Simulation Module, Navigation Message Generation Module, Error Generation Module, GNSS IF Signal Generation Module, and Message & Signal Steering Module. We verified the signal generated by the GNSS signal generation algorithm using software receiver for generation of signal brother to real GNSS signal.

• Journal of electromagnetic engineering and science
• /
• v.17 no.3
• /
• pp.120-125
• /
• 2017

A satellite communication (Satcom) antenna mounted on a moving platform provides a controlled heading that enables a geosynchronous satellite to communicate with the ground. A monopulse tracking method is effective for antenna control on a vehicle when it vibrates severely. However, this method has unexpected obstacles and its control performance is insufficient. To improve its control performance, the control command and monopulse error, the signal delay, and the radome effect are evaluated through tests. The authors then propose a method to transform the antenna error from 3D coordinates to 2D antenna coordinates. As a result, the antenna control performance is improved. As indicated in this study, examining antenna systems using the monopulse method on moving platforms is possible by understanding the antenna test process.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.30B no.9
• /
• pp.27-35
• /
• 1993

In this paper, a new algorithm for high level security and quality of speech is proposed. The algorithm is based on the rearrangement of the fast fourier transform (FFT) coefficients with pre and post filter process, hamming window and adaptive pseudo spectrum insertion. Then, the pre and post filters are used for the whitening of speech spectrum and the adaptive pseudo spectrum is inserted for the unclassification of silence/speech. Also, the hamming window technique is applied for the robustness to the syncronization error in the telephone line. According to the simulation results, it can be seen that the security of scrambled signal and the quality of descrambled signal have been improved fairly in both subjective and objective performance test and the new FFT scrambler is robust to the synchronization error.