• 센서학회지
• /
• 제24권3호
• /
• pp.208-213
• /
• 2015

The purpose of this study is to optimize the design of a capacitive pressure sensor element using the simulation of electrical characteristics. The simulation of the ceramic sensor diaphragm ($Al_2O_3$) was performed by permitting pressure to change the curvature of the diaphragm. The pressure capacitance ($C_P$) was increased from 19.63 pF to 15.26 pF by applying pressure because the distance between the electrodes has been changed from $30{\mu}m$ to $15{\mu}m$. When the thickness of the diaphragm was changed to 0.46~0.52 mm, a larger capacitance change showed in accordance with the reduced thickness, which means an increase of sensitivity. However, considering the viewpoint of the signal linearity, it was selected for the optimum thickness of the diaphragm to 0.50 mm. The designed sensor element based on simulated results was tested to measure the output characteristics. Comparing of simulated and measured results, there was a margin of error of approximately 2%.

• Journal of Power Electronics
• /
• 제18권6호
• /
• pp.1830-1843
• /
• 2018

In this paper, the generation of a reference current and voltage signal based on a Kalman filter is offered for a 3-phase 4wire UPQC (Unified Power Quality Conditioner). The performance of the UPQC is improved with source voltages that are distorted due to harmonic components. Despite harmonic and frequency variations, the Kalman filter is capable enough to determine the amplitude and the phase angle of load currents and source voltages. The calculation of the first state is sufficient to identify the fundamental components of the current, voltage and angle. Therefore, the Kalman state estimator is fast and simple. A Kalman based control strategy is proposed and implemented for a UPQC in a distribution system. The performance of the proposed control strategy is assessed for all possible source conditions with varying nonlinear and linear loads. The functioning of the proposed control algorithm with a UPQC is scrutinized and validated through simulations employing MATLAB/Simulink software. Using a FPGA SPATRAN 3A DSP board, the proposed algorithm is developed and implemented. A small-scale laboratory prototype is built to verify the simulation results. The stated control scheme for the UPQC reduces the following issues, voltage sags, voltage swells, harmonic distortions (voltage and current), unbalanced supply voltage and unbalanced power factor under dynamic and steady-state operating conditions.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2010년도 춘계학술대회 논문집
• /
• pp.1861-1867
• /
• 2010

This paper described the positioning algorithm of partial discharge in insulation oil by acoustic method for the application of an on-line diagnosis in oil-immersed transformers. In the experiment, five AE sensors having the resonant frequency of 150 kHz were used, and a signal conditioner was fabricated. A needle-plane electrode system which is composed of a needle with a curvature radius of $10{\mu}m$ and a plane electrode with a diameter of 60 mm was installed to simulate partial discharges in insulation oil. From the time difference of arrival (TOA) of acoustic signal, we calculated the location of partial discharge in insulation oil. In the experiment, an algorithm of positioning of PD occurrence by the time difference of arrival was proposed. From the experimental results, the positioning error of PD calculated by three AE sensors was within 4%.

• 한국정밀공학회지
• /
• 제11권5호
• /
• pp.180-188
• /
• 1994

Error assessment and evaluation for machine for machine tool slides have been considered as essential tools for improving accuracy. In this paper, a computer aided measurement technique is proposed using photo pin diodes of quadrant type and laser source. In thedeveloped system, three photo diodes are mounted on a sensor mounting table, and the sensored signal is processed by specially designed signal conditioner to give fine resolution with minimum noise. A micro computer inputs the processed signal, and the geometric errors of five degree of freedoms are successfully evaluated. Pitch, roll, yaw, vertical and horizontal straightness errors are thus assessed simultaneously for a machine tool slide. Calibration techniques such as optics calibration, photo diode calibration are proposed and implemented, giving precise calibration for the measurement system. The developed system has been applied to a practical machine tool slide, and has been found as one of efficient and precise technique for machine tool slide.

• 전자공학회논문지
• /
• 제53권5호
• /
• pp.152-159
• /
• 2016

본 논문은 CMOS 자기센서(hall Sensor)의 오프셋 및 1/f 잡음 제거기술 기반 고선형 자기센서 신호처리장치를 제안한다. 제안하는 자기센서는 자계(magnetic Field)를 감지하여 자계의 변화량에 따른 홀 전압(hall Voltage)을 출력하는 홀 플레이트(hall Plate)와 홀 플레이트 출력 신호의 오프셋과 1/f 잡음 제거 및 디지털화를 위한 자기센서 신호처리시스템으로 구성된다. 자기센서 신호처리 시스템은 스피닝 전류 바이어싱(spinning current biasing)을 통해 자기신호로부터 오프셋과 1/f잡음 성분을 분리하고, 초퍼 및 증폭기를 통해 자기신호를 100 kHz 주파수 대역으로 변조한다. 60 kHz 차단주파수를 갖는 고역통과필터(highpass filter)를 사용하여 오프셋 및 1/f 잡음을 제거한뒤 ADC(analog to digital converter)를 통해 자기신호만을 디지털 변조한다. 증폭기 및 고역통과필터 출력은 자기신호 -53.9 dBm @ 100 kHz, 잡음성부은 -101.3 dBm @ 10 kHz이다. 최종적으로 ADC를 통과한 자기센서 출력은 -5.0 dBm @ 100 kHz이고, 오프셋 및 1/f 잡음은 -55.0 dBm @ 10 kHz이다.

• Journal of Electrical Engineering and Technology
• /
• 제9권6호
• /
• pp.2004-2012
• /
• 2014

Energy storage devices are necessary to obtain stable utilization of renewable energy sources. When black-out occurs, distributed renewable power sources with energy storage devices can operate under standalone mode as uninterruptable power supply. This paper proposes a dynamic response analysis with small-signal modeling for the standalone operation of a photovoltaic power generation system that includes a bidirectional charger/discharger with a battery. Furthermore, it proposes a DC-link voltage controller design of the entire power conditioning system, using the storage current under standalone operation. The purpose of this controller is to guarantee the stable operation of the renewable source and the storage subsystem, with the power conversion of a very efficient bypass-type PCS. This paper presents the operating principle and design guidelines of the proposed scheme, along with performance analysis and simulation. Finally, a hardware prototype of 1-kW power conditioning system with an energy storage device is implemented, for experimental verification of the proposed converter system.

• 제어로봇시스템학회논문지
• /
• 제10권2호
• /
• pp.171-177
• /
• 2004

Many instrumentations have been used to acquire the performance data of military systems fer many years. But they could not satisfy environmental specifications(vibration, shock, temperature) and processing speed to apply for the performance test of military systems because of having developed as common vehicles/fixed installation equipments. Thus a new rugged embedded measurement system is required to process large data in high processing speed(Maximum sample rate:1.25Mhz/ch) with rugged environmental specifications. We have developed embedded measurement systems by using PXI(PCI extension for Instrumentation)bus interface composed of a stand alone controller and versatile data acquisition boards(analog, digital, vision, temperature and small signal conditioner) on PC-based environment to solve these problems. Operation programs have been developed using Lab_View and the performances have been validated experimentally.

• 한국소음진동공학회논문집
• /
• 제21권3호
• /
• pp.206-211
• /
• 2011

In this paper, we report a high-precision wireless gap sensor based on a surface acoustic wave (SAW) device. The sensing element is a parallel-plate capacitor whose dimensions are $3{\times}3\;mm^2$, and is attached to the SAW device as an external load. The SAW device, equipped with an RF antenna, serves simultaneously as a signal conditioner and an RF transponder. The center frequency of the SAW device is 450 MHz. The wireless gap sensor prototype exhibits a resolution of 100 nm and a sensing range of $50{\mu}m$. The proposed sensor system can be used for remote, high-precision gap measurement in hard-to-reach environments.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1998년도 춘계학술대회논문집; 용평리조트 타워콘도, 21-22 May 1998
• /
• pp.542-547
• /
• 1998

As the concern for a global energy conservation and environmental protection are increasing, it has been more important thing to correspond with CFC depletion. Alternate refrigerants have merit such as lower global warming effect, but also have demerits such as lower efficiency, miscibility, increasing noise and poor reliability problems. Then we have to develop more efficient, silent and robust compressors to satisfying world-wide demand. In this paper, parametric study on rotary compressor muffler for a room air-conditioner was carried out to investigate the effect of important design variables on noise by using Taguchi robust design method with signal-to-noise(S/N) ratio. Taguchi method seems to be helpful for finding optimum value of design variables for noise level. We also applied neural network to find optimal value of design variables.

• Transactions on Electrical and Electronic Materials
• /
• 제8권1호
• /
• pp.11-14
• /
• 2007

Consumables used in Chemical Mechanical Polishing (CMP) have been played important role to improve quality and productivity. Since the properties of consumables constantly change with various reasons, such as shelf time, manufactured time, lot to lot variation from supplier and so on, CMP results are not constant during the process. Also, CMP process results are affected by multiple sources from wafer, conditioner, pad and slurry. Therefore, multiple sensing systems are required to monitor CMP process variation. In this paper, the authors focus on development of monitoring system for CMP process which consist of force, temperature and displacement sensor to measure the signal from CMP process. With monitoring systems mentioned above, complex CMP phenomena can be investigated more clearly.